Listar por autor UPNA "Fuertes Bonel, Juan Pablo"
Mostrando ítems 1-17 de 17
-
Análisis y modelización del daño en elementos mecánicos obtenidos a partir de material nanoestructurado
En la presente tesis doctoral se aborda el diseño de un componente mecánico con estructura submicrométrica, obtenido a partir de material previamente procesado mediante Deformación Plástica Severa (SPD) por Extrusión en ... -
Analysis of fatigue and wear behaviour in ultrafine grained connecting rods
Over the last few years there has been an increasing interest in the study and development of processes that make it possible to obtain ultra-fine grained materials. Although there exists a large number of published works ... -
Analysis of tribological properties in disks of AA-5754 and AA-5083 aluminium alloys previously processed by equal channel angular pressing and isothermally forged
In the present study, the wear behaviour of two aluminium alloys (AA‐5754 and AA‐5083) is analysed where these have been previously processed by severe plastic deformation (SPD) with equal channel angular pressing (ECAP). ... -
Analysis on the manufacturing of an AA5083 straight blade previously ECAE processed
Over these past few years, there have been a large number of technical papers published related to the problem of improving the mechanical properties of materials obtained through severe plastic deformation. Nevertheless, ... -
Comparative study of the damage attained with different specimens by FEM
This present research work deals with the analysis of the design of different specimen geometries so that by finite volume simulations, the appearance of cracks may be predicted in the case of forging processes. To this ... -
Design and mechanical properties analysis of AA5083 ultrafine grained cams
This present research work deals with the development of ultrafine grained cams obtained from previously ECAP (Equal Channel Angular Pressing)-processed material and manufactured by isothermal forging. The design and the ... -
Design and optimization of the dies for the isothermal forging of a cam
In the present study, the design of the dies required for the isothermal forging of a cam is analysed by finite volume method. Specifically, cams are of great importance in automotive industry, where a lower weight and ... -
Design, optimization, and mechanical property analysis of a submicrometric aluminium alloy connecting rod
Ultrafine grained materials have a great deal of both scientific and technological interest because they allow outstanding properties to be obtained. An improvement in the mechanical strength and in the ductility and a ... -
Design, simulation and manufacturing of a connecting rod from ultra-fine grained material and isothermal forging
In this research work, a study on the mechanical properties of isothermal forging for connecting rods is made from previously ECAP (Equal Channel Angular Pressing)-processed AA1050 and AA5083 aluminium alloys. This severe ... -
Designing multifunctional protective PVC electrospun fibers with tunable properties
In this work, the electrospinning technique is used for the fabrication of electrospun functional fibers with desired properties in order to show a superhydrophobic behavior. With the aim to obtain a coating with the best ... -
Experimental and FEM analysis of wear behaviour in AA5083 ultrafine-grained cams
Severe plastic deformation (SPD) processes have attracted a great deal of both scientific and technological interest over the last few years as a consequence of the improvements that are possible to obtain in the microstructure ... -
Experimental measurement of the thermal conductivity of fused deposition modeling materials with a DTC-25 conductivity meter
The expansion and low cost of additive manufacturing technologies have led to a revolution in the development of materials used by these technologies. There are several varieties of materials that can be used in additive ... -
Experimental modelling of critical damage obtained in Al-Mg and Al-Mn alloys for both annealed state and previously deformed by ECAP
Assessing the damage produced in plastic deformation processes permits the optimum manner to shape a material that could avoid any cracks from appearing. In this present research work, the absolute critical damage in ... -
Manufacturing of nanostructured rings from previously ECAE-processed AA5083 alloy by isothermal forging
The manufacturing of a functional hollow mechanical element or ring of the AA5083 alloy previously equal channel angular extrusion (ECAE) processed, which presents a submicrometric microstructure, is dealt with. For this ... -
Mechanical properties analysis of an Al-Mg alloy connecting rod with submicrometric structure
Over these last few years, there has been a growing interest in developing mechanical components from submicrometric materials due to the significant improvement that these materials present compared to their original ... -
Modeling experimental parameters for the fabrication of multifunctional surfaces composed of electrospun pcl/zno-nps nanofibers
In this work, a one-step electrospinning technique has been implemented for the design and development of functional surfaces with a desired morphology in terms of wettability and corrosion resistance by using polycaprolactone ... -
A proposal of a constitutive description for aluminium alloys in both cold and hot working
The most important difficulties when the behaviour of a part that is subjected to external mechanical forces is simulated deal with the determination of both the material thermo-mechanical properties and its boundary ...