Browsing by Author "Urrutia Azcona, Aitor"
Now showing 1 - 20 of 35
Results Per Page
Sort Options
Publication Open Access Advances in fiber optic DNA-based sensors: a review(IEEE, 2021) Santano Rivero, Desiree; Urrutia Azcona, Aitor; Ruiz Zamarreño, Carlos; Del Villar, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate PublikoaDNA is becoming increasingly important in the domain of optical fiber sensors, either as a tool for biosensing, or as a target to detect. In this review the main contributions of the last years are presented both in the domain of wavelength and intensity based configurations. This review comprises the use of natural single strand DNA (ssDNA) sequences as receptors for the detection of ssDNA sequences through hybridization, synthetic nucleic acids receptors for detection of complementary ssDNA sequences, and sensors based on natural and synthetic ssDNA receptors used for the detection of non-DNA targets. Parameters such as sensitivity, detection range and limit of detection are analyzed and discussed in detail to the purpose of comparing the different technologies and knowing the future lines to follow in the domain of fiber optic DNA-based sensors.Publication Open Access An antibacterial coating based on a polymer/sol-gel hybrid matrix loaded with silver nanoparticles(Springer, 2011) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta ElektronikoaIn this work a novel antibacterial surface composed of an organic-inorganic hybrid matrix of tetraorthosilicate and a polyelectrolyte is presented. A precursor solution of tetraethoxysilane (TEOS) and poly(acrylic acid sodium salt) (PAA) was prepared and subsequently thin films were fabricated by the dip-coating technique using glass slides as substrates. This hybrid matrix coating is further loaded with silver nanoparticles using an in situ synthesis route. The morphology and composition of the coatings have been studied using UV-VIS spectroscopy and atomic force microscopy (AFM). Energy dispersive X-ray (EDX) was also used to confirm the presence of the resulting silver nanoparticles within the thin films. Finally the coatings have been tested in bacterial cultures of genus Lactobacillus plantarum to observe their antibacterial properties. It has been experimentally demonstrated that these silver loaded organic-inorganic hybrid films have a very good antimicrobial behavior against this type of bacteria.Publication Open Access An antibacterial submicron fiber mat with in situ synthesized silver nanoparticles(Wiley, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rodríguez, Yoany; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2This work presents an alternative approachfor fabricating electrospun submicron highly hydrophilicfiber mats loaded with silver nanoparticles. These fiber matsshow a high efficient antibacterial behavior, very attractivefor applications like wound healing and skin regenerationprocesses. The fabrication method is divided in two steps.First, poly(acrylic acid) (PAA) and b-cyclodextrin (b-CD)submicron fibers were electrospun and further stabilizedusing a thermal treatment, yielding stable hydrogel-likefibers with diameters ranging from 100 nm up to severalmicrons. In the second step, silver ions were loaded into thefibers and then reduced to silver nanoparticles in-situ. Theelectrospinning parameters were adjusted to achieve thedesired properties of the fiber mat (density, size) and after-wards, the characteristics of the silver nanoparticles(amount, size, aggregation) were tuned by controlling thesilver ion loading mechanism. Highly biocide surfaces wereachieved showing more than 99.99% of killing efficiency.The two-step process improves the reproducibility and tun-ability of the fiber mats. To our knowledge, this is the firsttime that stable hydrogel fibers with a highly biocide behav-ior have been fabricated using electrospinning.Publication Open Access An antibacterial surface coating composed of PAH/SiO2 nanostructurated films by layer by layer(Wiley, 2010) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Ruete Ibarrola, Leyre; Goicoechea Fernández, Javier; Fernández Valdivielso, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISCIn this work we propose a novel antibacterial coating composed of SiO2 and the polymer Poly(allylamine hydrochloride) (PAH). The coating was fabricated by the technique Layer-by-Layer (LbL). This technique has already been used in previous works, and it has the advantage that it allows to control the construction of nanosized and well organized multilayer films. Here, the new nanotexturized LbL SiO2 surface acts as antibacterial agent. The fabricated coatings have been tested in bacterial cultures of genus Lactobacillus to observe their antibacterial properties. It has been demonstrated these PAH/SiO2 coating films have a very good antimicrobial behaviour against this type of bacteria.Publication Open Access An antibacterial surface coating composed of PAH/SiO2 nanostructurated films by Layer by Layer(2009) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Ruete Ibarrola, Leyre; Goicoechea Fernández, Javier; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako GobernuaIn this article we propose a novel antibacterial coating composed of SiO2 and the polymer Poly(allylamine hydrochloride) (PAH) on glass slides by the technique Layer-by- Layer (LbL)1. This technique has already used in previous works, and it has the advantage that it allows to control the construction of nanosized and well organized multilayer films. In this work, the new nanotexturized LbL SiO2 surface acts as antibacterial agent. The fabricated coatings have been tested in bacterial cultures of genus Lactobacillus to observe their antibacterial properties.Publication Open Access A comprehensive review of optical fiber refractometers: toward a standard comparative criterion(Wiley, 2019) Urrutia Azcona, Aitor; Del Villar, Ignacio; Zubiate Orzanco, Pablo; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISCThanks to the peculiarities of optical fiber and its ability to be combined with nanotechnology, precise and accurate measurements of the changes in optical properties (i.e., refractive index) of the medium surrounding the fiber are becoming possible with a high degree of performance. Thus, optical fiber sensors (OFSs) are increasingly finding applications in biochemistry and biomedicine. Here, all types of optical fiber refractometers are covered, and they are classified into three main groups: interferometers, grating-based structures, and resonance-based structures (the resonance is induced by coating the optical fiber sensor with a thin film). The performance of these different structures is compared by means of the most common parameters: sensitivity, full width at half minimum or maximum, figure of merit, and quality factor. The aim here is to provide a reliable and easy-to-use tool to compare the performance of the most recent developments on fiber optic refractometers.Publication Open Access Continuous liquid-level sensor based on a long-period grating and microwave photonics filtering techniques(IEEE, 2016) Ricchiuti, Amelia L.; Barrera, D.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate PublikoaA fiber optic liquid-level sensor based on a long period grating (LPG) is proposed and experimentally validated. The principle of operation is based on a technique used to analyze microwave photonics filters. A 4-cm-long LPG cascaded with a high-reflectivity fiber Bragg grating is employed to achieve a continuous liquid-level sensor. The measurements have been performed using a modulator and a photo-detector with a modest bandwidth of less than 500 MHz, showing a sensitivity of -12.71 dB/cm and a standard deviation of 0.52 dB. One of the significant advantages of such sensing structure is that it is based on low-bandwidth radio frequency and off-the-shelf photonic components. In addition, the simple proposed scheme presents good repeatable performance and proves to be intrinsically robust against environmental changes, stable, and easy to reconfigure.Publication Open Access Development of optical fiber humidity sensor based on silver nanoparticles-embedded coatings(2015) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua: IIQ14064.RI1; Universidad Pública de Navarra / Nafarroako Unibertsitate PublikoaEl desarrollo de nuevos materiales y métodos de deposición a escala nanométrica ha supuesto una auténtica revolución en muchas disciplinas de la investigación. En particular, en el campo de los sensores de fibra óptica, los recubrimientos nanoestructurados permiten generar efectos ópticos que no son apreciables mediante la utilización de materiales convencionales. El principal objetivo de esta tesis es la fabricación de nuevos sensores de humedad de fibra óptica basados en nanofibras y películas nanoestructuradas que posean propiedades antibacterianas para aplicaciones que operan en entornos de alta humedad y probacterianos. Para ello, el estudio y síntesis de nanopartículas de plata, y su posterior inclusión en los procesos de fabricación de recubrimientos como electrospinning y Layer-by-Layer han sido analizados para la fabricación de películas antibacterianas sobre fibra óptica. De esta forma, se han estudiado y desarrollado en este trabajo diferentes arquitecturas sensoras basadas en campo evanescente, resonancias basadas en plasmones superficiales localizados y modos de pérdidas, y fibras tipo Long period gratings.Publication Embargo Diseño e implementación de prototipo de dispositivo portable para apoyo a personas con disfunción olfativa(2021) Castaño de Egüés, Lorena Yveth; Urrutia Azcona, Aitor; Socorro Leránoz, Abián Bentor; Escuela Técnica Superior de Ingeniería Industrial, Informática y de Telecomunicación; Industria, Informatika eta Telekomunikazio Ingeniaritzako Goi Mailako Eskola TeknikoaLa anosmia es una de las consecuencias del COVID-19 con la que tienen que aprender a vivir algunas de las personas que han sobrevivido a éste y con el que viven muchas personas desde siempre. En aras de aprovechar las plataformas electrónicas existentes y ayudar al bienestar físico, mental y social de las personas con diversidad funcional olfativa surge la inquietud por desarrollar un dispositivo portable que ayude a protegerse de los gases dañinos para la salud. Este proyecto propone el diseño, implementación y caracterización de un prototipo de experimentación, que permita demostrar la viabilidad de una pulsera de uso personal, mediante la adquisición y discriminación de distintos odorantes que representan alto riesgo para la salud. Para la realización del dispositivo ha sido necesario un estudio previo de los gases tóxicos para la salud y las distintas técnicas de detección de gases tanto a nivel sanitario como a nivel industrial y comercial, así como los sensores existentes. En este documento se han descrito los conceptos para entender que es y cómo funciona el dispositivo portable. El desarrollo del prototipo consta de la elaboración de software, implementación hardware, comunicación inalámbrica con el móvil, comunicación por puerto USB con el ordenador y diseño de PCB. Una vez implementado se realizaron en laboratorio las pruebas de caracterización con un panel de gases. Luego de finalizar las pruebas se realizó la tarjeta PCB y caja contenedora del prototipo. Se ha demostrado que utilizando la plataforma libre de Arduino se puede implementar un sistema funcional, estable y económico para su uso frente a gases nocivos para la salud.Publication Open Access Effect of both protective and reducing agents in the synthesis of multicolor silver nanoparticles(Springer, 2013) Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Urrutia Azcona, Aitor; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta ElektronikoaIn this paper, the influence of variable molar ratios between reducing and loading agents (1:100, 1:50, 1:20, 1:10, 1:5, 1:2, 1:1, 2:1) and between protective and loading agents (0.3:1, 0.75:1, 1.5:1, 3:1, 7.5:1, 30:1, 75:1) in the synthesis of silver nanoparticles by chemical reduction has been evaluated to obtain multicolor nanoparticles with a high stability in time. The protective agent poly(acrylic acid, sodium salt) (PAA) and reducing agent dimethylaminoborane (DMAB) play a key role in the formation of the resultant color. Evolution of the optical absorption bands of the silver nanoparticles as a function of PAA and DMAB molar ratios made it possible to confirm the presence of silver nanoparticles or clusters with a specific shape. The results reveal that a wide range of colors (violet, blue, green, brown, yellow, red, orange), sizes (from nanometer to micrometer), and shapes (cubic, rod, triangle, hexagonal, spherical) can be perfectly tuned by means of a fine control of the PAA and DMAB molar concentrations.Publication Open Access Electrospun nanofiber mats for evanescent optical fiber sensors(Elsevier, 2013) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rivero Fuente, Pedro J.; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate PublikoaIn this work, a study about the optical response of electrospun nanofiber (ENF) coatings for their use in evanescent optical fiber sensors is presented. Several types of ENF mats composed of poly(acrylic acid) (PAA) were developed with different ENF diameters and densities. These ENF mats were deposited onto an optical fiber core in order to fabricate humidity evanescent optical fiber sensors. The devices were exposed to relative humidity (RH) variations from 30% RH to 95%RH. The transfer functions of the devices (transmitted optical power versus relative humidity) presented two well-differenced behaviors depending on the ENF diameter and the ENF mat density. The devices with lower ENF diameters and higher mat density showed an increase in the transmitted optical power when RH increased. On the contrary, the devices with higher ENF diameters and lower mat density showed a decrease in the transmitted optical power when RH increased. In addition to this, sensors with thinner ENF overlays, showed a higher sensitivity. In order to study the response time of these devices, the ENFs sensors were submitted to human breathing cycles and presented a response time around 340 ms (exhalation). In spite of the high RH conditions of this experiment, the devices showed a recovery time around 210 ms and a negligible hysteresis or drift with respect to the initial condition (inhalation).Publication Open Access Estudio de la fabricación de recubrimientos parciales y su influencia en la respuesta óptica de dispositivos LPG(2016) Gordillo Valencia, Juan; Goicoechea Fernández, Javier; Urrutia Azcona, Aitor; Escuela Técnica Superior de Ingenieros Industriales y de Telecomunicación; Telekomunikazio eta Industria Ingeniarien Goi Mailako Eskola TeknikoaEn los últimos tiempos se ha observado un aumento de las aplicaciones relacionadas o basadas en fibra óptica. Este crecimiento se debe a la popularización del uso de este material en muchos ámbitos de la vida cotidiana promovido por la explosión tecnológica actual. Este proyecto persigue varios objetivos que a pesar de estar íntimamente ligados se pueden diferenciar claramente. En primer lugar, buscamos comprobar la viabilidad de un sensor dual temperatura/humedad relativa, este sensor estará construido sobre dos componentes esenciales, una fibra óptica sometida a un tratamiento que comúnmente se conoce como Long-period fiber grating y un recubrimiento polimérico. Las sumas de las propiedades físicas de estos dos componentes configuran la posible respuesta del sensor que buscamos, para comprobar que esta respuesta física es correlativa a los resultados que estamos buscando existe la necesidad de generar una serie de algoritmos de análisis matemáticos para dicha comprobación, esta necesidad configura el segundo objetivo de este proyecto.Publication Embargo Estudio de materiales basados en nanoestructuras para la detección de radiación ionizante(2022) Hernández Castro, Frank; Urrutia Azcona, Aitor; Socorro Leránoz, Abián Bentor; Escuela Técnica Superior de Ingeniería Industrial, Informática y de Telecomunicación; Industria, Informatika eta Telekomunikazio Ingeniaritzako Goi Mailako Eskola TeknikoaEl siguiente trabajo realiza un estudio del comportamiento de una solución de PAA y AgNO3 con 3 concentraciones molares diferentes y 3 volúmenes de agente reductor añadido frente a radiación ionizante. Las muestras fueron expuestas a dosis entre 20 Gy y 160 Gy de fotones de rayos X en un acelerador lineal (LINAC) TrueBeam de la empresa Varian Medical Systems a una tasa de dosis de 10 Gy/min. Los resultados fueron analizados a partir de los datos de absorbancia recopilados de las muestras empleando un espectrómetro UV-Vis de doble haz Jasco V-630. Los resultados obtenidos arrojan que las muestras variaron su absorbancia en todos los casos, excepto para concentraciones más bajas de AgNO3 y ningún agente reductor añadido. Se aprecia una disminución de los valores de absorbancia en las muestras que contenían altos volúmenes de agente reductor y bajas concentraciones de AgNO3 y un aumento de la respuesta lineal de las muestras verificado mediante el cálculo del R-cuadrado de la curva de ajuste lineal por mínimos cuadrados de la serie de muestras.Publication Open Access Fiber-based early diagnosis of venous thromboembolic disease by label-free D-dimer detection(Elsevier, 2019) Zubiate Orzanco, Pablo; Urrutia Azcona, Aitor; Ruiz Zamarreño, Carlos; Egea Urra, Josune; Fernández Irigoyen, Joaquín; Giannetti, Ambra; Baldini, Francesco; Díaz Lucas, Silvia; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Santamaría Martínez, Enrique; Chiavaioli, Francesco; Del Villar, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako GobernuaD-dimer is a useful diagnostic biomarker for deep vein thrombosis or pulmonary embolism, collectively referred to as venous thromboembolism (VTE). The ability to detect in real-time the amount of D-dimer with a fast and reliable method is a key step to anticipate the appearance of these diseases. Here, the results of a highly specific and sensitive biosensor for the detection of D-dimer based on lossy mode resonance in fiber optics are presented. The unique features of specialty fibers in light management integrated with microfluidics allow detecting D-dimer in human serum with a detection limit of 100 ng/mL, a value 5-fold below the clinical cutoff value. Comparison of the results achieved with mass-spectrometry-based proteomics, which allows for the identification of beta- and gamma-chains of fibrinogen, demonstrates the ability of our platform to specifically (>90%) recognize D-dimer. Therefore, this technology potentially represents a paradigm shift in the development of a simple, high-specificity and label-free biosensing platform, which can be applied to speed up diagnostic healthcare processes of venous thromboembolism toward an early diagnostic and personalized treatment system.Publication Open Access Fiber-based label-free D-dimer detection for early diagnosis of venous thromboembolism(SPIE, 2020) Zubiate Orzanco, Pablo; Urrutia Azcona, Aitor; Ruiz Zamarreño, Carlos; Fernández Irigoyen, Joaquín; Giannetti, Ambra; Baldini, Francesco; Díaz Lucas, Silvia; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Santamaría Martínez, Enrique; Del Villar, Ignacio; Chiavaioli, Francesco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónD-dimer is a useful diagnostic biomarker for deep vein thrombosis or pulmonary embolism, collectively referred to as venous thromboembolism (VTE). The ability to detect in real-time the amount of D-dimer with a fast and reliable method is a key step to anticipate the appearance of these diseases. The combination of fiber-optic-based platforms for biosensing with the nanotechnologies is opening up the chance for the development of in situ, portable, lightweight, versatile, reliable and high-performance optical sensing devices towards lab-on-fiber technology. The generation of lossy mode resonances (LMRs) by means of the deposition of nm-thick absorbing metal-oxide films on special geometric-modified fibers allows measuring precisely and accurately surface refractive index changes, which are due to the binding interaction between a biological recognition element and the analyte under investigation. This approach enhances the light-matter interaction in a strong way, thus turning out to be more sensitive compared to other optical technology platforms, such as fiber gratings or surface plasmon resonance. Here, the results of a highly specific and sensitive biosensor for the detection of D-dimer based on LMR in fiber-optics are presented by monitoring in real-time the shift of the LMR related to the biomolecule interactions thanks to a conventional wavelength-interrogation system and an ad-hoc developed microfluidics. A detection limit of 100 ng/mL, a value 5-fold below the clinical cutoff value, has been attained for D-dimer spiked in human serum. The comparison of the results achieved with proteomics-based methodologies, which allows for the identification of betaand gamma-chains of fibrinogen, demonstrates the ability of our platform to specifically (>90%) recognize D-dimer.Publication Open Access Fiber-optic lossy mode resonance sensors(Elsevier, 2014) Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Corres Sanz, Jesús María; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Elosúa Aguado, César; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako GobernuaIn the last 4 years, experimental evidences about the potential use of optical sensors based on Lossy Mode Resonances (LMR) have been presented in the literature. These LMR sensors have some similarities with Surface Plasmon Resonance (SPR) sensors, the gold standard in label-free, real-time biomolecular interaction analysis. In these new LMR sensors, if the non-metallic nanocladding of an optical waveguide fulfills the conditions explained in this work, coupling of light to the cladding modes happens at certain resonance wavelengths, which enables the use of LMR devices as refractometers and opens the door to diverse applications such as in biology and proteomics research. These highly sensitive refractometers have already shown sensitivities higher than 20,000 nm/RIU or 5x10-7 RIU and, given the youth of this field, it is expected to achieve even better values.Publication Open Access Humidity sensor based on a long-period fiber grating coated with a hydrophobic thin film(2010) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y ElectrónicaIn this work it is proposed a novel fiber optic humidity sensor based on a functionally coated long-period fiber grating (LPG). The coating is composed of tetraorthosilicate matrix functionalized with perfluorooctyltriethoxysilane and its fabrication was performed by the sol-gel technique using a dip coating process using the LPG as substrate. This technique allows to fabricate sensitive films in a fast and simple way compared to other overlay fabrication techniques. The fabricated sensor was tested in a programmable temperature and climatic chamber. Relative humidity (RH) was varied in range from 20%RH to 80%RH at room temperature. The results showed a smooth exponential-like wavelength shift of the LPG attenuation band.Publication Open Access Humidity sensor based on silver nanopartlcles embedded in a polymeric coating(Sciendo, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISCIn this work, it is presented a novel optical fiber humidity sensor based on silver nanoparticle-loaded polymeric coatings built onto an optical fiber core. The polymeric film was fabricated using the Layer-by-Layer assembly technique. The silver nanoparticles (Ag NPs) were characterized using transmission electron microscopy (TEM and UV-VIS spectroscopy. A Localized Surface Plasmon Resonance (LSPR) attenuation band is observed when the thickness of the coating increases, and showed a very good sensitivity to Relative Humidity (RH) variations, suitable for high performance applications such as human breathing monitoring.Publication Restricted Implementación de nanorecubrimientos especiales para distintas aplicaciones(2009) Urrutia Azcona, Aitor; Matías Maestro, Ignacio; Escuela Técnica Superior de Ingenieros Industriales y de Telecomunicación; Telekomunikazio eta Industria Ingeniarien Goi Mailako Eskola Teknikoa; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta ElektronikoaPublication Open Access Labyrinth metasurface absorber for ultra-high-sensitivity terahertz thin film sensing(Wiley, 2018) Jáuregui López, Irati; Rodríguez Ulibarri, Pablo; Urrutia Azcona, Aitor; Kuznetsov, Sergei A.; Beruete Díaz, Miguel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónIn this work, a labyrinth metasurface sensor operating at the low‐frequency edge of the THz band is presented. Its intricate shape leads to a high electric field confinement on the surface of the structure, resulting in ultrasensitive performance, able to detect samples of the order of tens of nanometers at a wavelength of the order of millimeters (i.e., five orders of magnitude larger). The sensing capabilities of the labyrinth metasurface are evaluated numerically and experimentally by covering the metallic face with tin dioxide (SnO2) thin films with thicknesses ranging from 24 to 345 nm. A redshift of the resonant frequency is observed as the analyte thickness increases, until reaching a thickness of 20 μm, where the response saturates. A maximum sensitivity of more than 800 and a figure of merit near 4500 nm−1 are achieved, allowing discriminating differences in the SnO2 thickness of less than 25 nm, and improving previous works by a factor of 35. This result can open a new paradigm of ultrasensitive devices based on intricate metageometries overcoming the limitations of classical metasurface sensor designs based on periodic metaatoms.