Artículos de revista DIEC - IEKS Aldizkari artikuluak

Permanent URI for this collection

http://hdl.handle.net/2454/29500

Browse

Now showing 1 - 20 of 45

Open Access
0.6-V CMOS bulk-driven instrumentation amplifier for IoMT bioimpedance analysis
(Wiley, 2024) Carrillo, Juan M.; Ocampo-Hidalgo, Juan J.; Corbacho, Israel; Cruz Blas, Carlos Aristóteles de la; Domínguez, Miguel Á.; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
An instrumentation amplifier (IA), aimed at wideband bioimpedance analysisin the low-voltage low-power scenario of internet of medical things (IoMT), ispresented. The operation principle is based on the indirect current feedbacktechnique, where an input and a feedback transconductor determine thevoltage gain of the preamplifier. The required transconductors consist of twobulk-driven flipped-voltage-follower cells and an active pseudo-resistor, thusleading to a linear and compact implementation. The circuit has been designedand fabricated in 180 nm CMOS technology to operate with a 0.6-V supply.Experimental results obtained from measurements on eight samples of thesilicon prototype show that when the IA is programmed to have a nominalvoltage gain of 11 V/V, the bandwidth is 316.2 kHz, the CMRR exceeds63 dB, and the maximum output voltage that can be processed with a THDbelow –40 dB is 555 mVpp.
Open Access
An acceleration approach for channel deterministic approaches based on quasi-stationary regions in V2X communications
(Institute of Electrical and Electronics Engineers, 2024) Rodríguez Corbo, Fidel Alejandro; Celaya Echarri, Mikel; Shubair, Raed M.; Falcone Lanas, Francisco; Azpilicueta Fernández de las Heras, Leyre; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Institute of Smart Cities - ISC
Vehicular environments are characterized by a high mobility, which alongside with the presence of abundant dynamic scatterers, lead to vehicular communication channels to be intrinsically non-stationary. In this sense, the quasi-stationary regions (QSRs) can assess the degree of non-stationarity within a determined scenario, and ultimately assist geometrical models to increase channel sampling intervals or to develop more efficient hybrid stochastic-geometric channel models. In this work, the channel QSRs in a vehicular communication (V2X) generic highdense urban environment at millimeter wave (mmWave) frequencies (28 GHz) have been analyzed using different approaches, such as the extended channel response into a Doppler-delay domain or the shadow fading spatial auto-correlation function (SF ACF) methodology. Then, the QSRs have been used as sampling distance in an in-house developed three-dimensional ray-launching (3D-RL) algorithm as an acceleration approach. The time variant channel features have been extracted and compared with the full resolution approach, obtaining consistent results when considering the QSR sampling distances, while decreasing by 83.30% the simulation computational time for the Doppler-delay approach, and 92.86% for the SF ACF method.
Open Access
Analyzing implicit gender bias in Optics and Photonics at the predoctoral stage in Spain
(Sociedad Española de Óptica, 2023) Tomás, María-Baralida; Heras, Alba de las; Santamaría Fernández, Beatriz; Gómez Varela, Ana Isabel; Benedi García, Clara; Delgado Pinar, Martina; González Fernández, Verónica; Pérez Herrera, Rosa Ana; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza
Los prejuicios de género desempeñan un papel muy importante en áreas relacionadas con la ciencia, la tecnología, la ingeniería y las matemáticas (STEM). La asociación del género con determinados atributos, comportamientos o profesiones conduce a una menor proporción de mujeres en STEM. En el campo de la Óptica y la Fotónica, podemos identificar una disparidad de género entre enfoques técnicos o bioclínicos dentro de la misma área al examinar la autoría de la tesis defendida. En este trabajo, cuantificamos el impacto del sesgo implícito de género en los programas de doctorado relacionados con la Óptica y Fotónica en España. Aquí presentamos un estudio exhaustivo sobre los descriptores UNESCO de las tesis defendidas en el periodo 2015-2020 a través del repositorio de acceso abierto TESEO, donde se recopilan todas las tesis doctorales de las universidades españolas. Se considera el programa de doctorado de cada tesis y se clasifica en una categoría técnica o bioclínica. Con esta clasificación, cuantificamos el número de autores y autoras dentro de cada categoría, y los resultados muestran un claro desequilibrio en la mayoría de los descriptores evaluados: los hombres son más propensos a elegir programas de doctorado técnicos, mientras que las mujeres están mayoritariamente presentes en programas clínicos o biológicos. Esta diferencia se observa incluso en los descriptores en los que ambos sexos están representados por igual. Por un lado, la infrarrepresentación femenina es mayor en "Física", "Astronomía y Astrofísica", "Ciencias de la Tierra y del Espacio" y "Ciencias Tecnológicas". Por el contrario, las áreas de "Química", "Ciencias de la Vida" y "Ciencias Médicas" muestran una distribución más equilibrada entre hombres y mujeres en la mayoría de los descriptores.
Open Access
An antibacterial submicron fiber mat with in situ synthesized silver nanoparticles
(Wiley, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rodríguez, Yoany; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
This work presents an alternative approachfor fabricating electrospun submicron highly hydrophilicfiber mats loaded with silver nanoparticles. These fiber matsshow a high efficient antibacterial behavior, very attractivefor applications like wound healing and skin regenerationprocesses. The fabrication method is divided in two steps.First, poly(acrylic acid) (PAA) and b-cyclodextrin (b-CD)submicron fibers were electrospun and further stabilizedusing a thermal treatment, yielding stable hydrogel-likefibers with diameters ranging from 100 nm up to severalmicrons. In the second step, silver ions were loaded into thefibers and then reduced to silver nanoparticles in-situ. Theelectrospinning parameters were adjusted to achieve thedesired properties of the fiber mat (density, size) and after-wards, the characteristics of the silver nanoparticles(amount, size, aggregation) were tuned by controlling thesilver ion loading mechanism. Highly biocide surfaces wereachieved showing more than 99.99% of killing efficiency.The two-step process improves the reproducibility and tun-ability of the fiber mats. To our knowledge, this is the firsttime that stable hydrogel fibers with a highly biocide behav-ior have been fabricated using electrospinning.
Open Access
An antibacterial surface coating composed of PAH/SiO2 nanostructurated films by layer by layer
(Wiley, 2010) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Ruete Ibarrola, Leyre; Goicoechea Fernández, Javier; Fernández Valdivielso, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
In this work we propose a novel antibacterial coating composed of SiO2 and the polymer Poly(allylamine hydrochloride) (PAH). The coating was fabricated by the technique Layer-by-Layer (LbL). This technique has already been used in previous works, and it has the advantage that it allows to control the construction of nanosized and well organized multilayer films. Here, the new nanotexturized LbL SiO2 surface acts as antibacterial agent. The fabricated coatings have been tested in bacterial cultures of genus Lactobacillus to observe their antibacterial properties. It has been demonstrated these PAH/SiO2 coating films have a very good antimicrobial behaviour against this type of bacteria.
Open Access
Application of coherently radiating periodic structures for feeding subarrays in limited-scan arrays
(IEEE, 2023) Juárez, Elizvan; Panduro, Marco A.; Covarrubias, David H.; Reyna, Alberto; Río Bocio, Carlos del; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza
This paper presents a new design technique to improve the reduction of phase shifters using sub-arrays and CORPS (coherently radiating periodic structures) technology. The CORPS network generates the values of cophasal excitation with reduced input ports. These values feed an optimal sub-arrays structure. Furthermore, fixed and variable amplifiers allow a low SLL (side lobe level) by using a raised cosine amplitude distribution along sub-arrays inputs. The theoretical model of CORPS-Subarrays, numerical and experimental results of several design cases are presented. The proposed design achieves a ±14° scanning range with a higher reduction of phase shifters than other techniques presented previously in the state of art. This paper illustrates, as a contribution, the complete antenna system based on the fabrication of a prototype and experimental results to analyze the reduction capacity of phase shifters and scanning possibilities of the proposed methodology in antenna arrays. The experimental results of the BFN (beam-forming networks) prototype at 6 GHz for 11 antenna elements and 3 phase shifters are provided. The proposed design achieves a reduction of 72% of phased shifters with ±14° beam scanning and −15 dB of SLL.
Open Access
Assessment of performance of one-turn inductors in series configuration through a transmission-line modeling approach
(IEEE , 2024) Álvarez Botero, Germán Andrés; Moctezuma-Pascual, Eduardo; Gómez Laso, Miguel Ángel; Torres-Torres, Reydezel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza
In this paper, transmission-line theory is applied to implement a physical model for compact one-turn inductors, which simultaneously incorporates the frequency-dependent effects introduced by the conductor skin effect and the loss originated by the coupling with the ground plane. For this purpose, S-parameter measurements are processed to extract the associated parameters, which exhibit scalability with the turn radius. This allows the model to be used for interpolation and extrapolation analyses. In this regard, the device performance is assessed for one-turn inductors in series connection, for different load impedances, and when the turn is narrowed. To validate the proposal, agreement between the model and the experimental transmission line RLGC parameters, the return loss, and the Q-factor is obtained up to 20 GHz.
Open Access
Automatic segmentation and quantification of Nigrosome-1 neuromelanin and iron in MRI: A candidate biomarker for parkinson's disease
(Wiley, 2023) Ariz Galilea, Mikel; Martínez, Martín; Álvarez, Ignacio; Fernández Seara, María A.; Castellanos, Gabriel; Catalonian Neuroimaging Parkinson's Disease Consortium; Pastor, Pau; Pastor, María A.; Ortiz de Solórzano, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Background: There is a lack of automated tools for the segmentation and quantification of neuromelanin (NM) and iron in the nigrosome-1 (N1). Existing tools evaluate the N1 sign, i.e., the presence or absence of the ‘swallow-tail’ in iron-sensitive MRI, or globally analyze the MRI signal in an area containing the N1, without providing a volumetric delineation. Purpose: Present an automated method to segment the N1 and quantify differences in N1's NM and iron content between Parkinson's disease (PD) patients and healthy controls (HCs). Study whether N1 degeneration is clinically related to PD and could be used as a biomarker of the disease. Study Type: Prospective. Subjects: Seventy-one PD (65.3 ± 10.3 years old, 34 female/37 male); 30 HC (62.7 ± 7.8 years old, 17 female/13 male). Field Strength/Sequence: 3 T Anatomical T1-weighted MPRAGE, NM-MRI T1-weighted gradient with magnetization transfer, susceptibility-weighted imaging (SWI). Assessment: N1 was automatically segmented in SWI images using a multi-image atlas, populated with healthy N1 structures manually annotated by a neurologist. Relative NM and iron content were quantified and their diagnostic performance assessed and compared with the substantia nigra pars compacta (SNc). The association between image parameters and clinically relevant variables was studied. Statistical Tests: Nonparametric tests were used (Mann-Whitney's U, chi-square, and Friedman tests) at P = 0.05. Results: N1's relative NM content decreased and relative iron content increased in PD patients compared with HCs (NM-CRHC = 22.55 ± 1.49; NM-CRPD = 19.79 ± 1.92; NM-nVolHC = 2.69 × 10-5 ± 1.02 × 10-5; NM-nVolPD = 1.18 × 10-5 ± 0.96 × 10−5; Iron-CRHC = 10.51 ± 2.64; Iron-CRPD = 19.35 ± 7.88; Iron-nVolHC = 0.72 × 10-5 ± 0.81 × 10-5; Iron-nVolPD = 2.82 × 10−5 ± 2.04 × 10−5). Binary logistic regression analyses combining N1 and SNc image parameters yielded a top AUC = 0.955. Significant correlation was found between most N1 parameters and both disease duration (ρNM-CR = -0.31; ρiron-CR = 0.43; ρiron-nVol = 0.46) and the motor status ρNM-nVol = -0.27; ρiron-CR = 0.33; ρiron-nVol = 0.28), suggesting NM reduction along with iron accumulation in N1 as the disease progresses. Data Conclusion: This method provides a fully automatic N1 segmentation, and the analyses performed reveal that N1 relative NM and iron quantification improves diagnostic performance and suggest a relative NM reduction along with a relative iron accumulation in N1 as the disease progresses. Evidence Level: 1. Technical Efficacy: Stage 1.
Embargo
Biosensing based on lossy mode resonances
(Elsevier, 2024) Matías Maestro, Ignacio; Imas González, José Javier; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Lossy mode resonance (LMR)-based sensors have experienced an important development in the last decade. Among the different domains in which LMR-based sensors have been used, biosensing is one of the fields that has attracted more interest in recent years. Here, LMR properties and some biosensing concepts are reviewed in the first place. Then, the progress of LMR-based biosensors is described, starting with cladding-removed multimode fibers (CRMMF), and evolving towards the employment of D-shaped single mode fibers, which have led to better biosensors in terms of performance and limit of detection (LOD). More recent advances, such as the development of biosensors that combine the optical and electrochemical domains, or the introduction of planar waveguides as the biosensor substrate, are also discussed. In all the cases, examples of biosensors are included, indicating the detected biomarker, biofunctionalization protocol, dynamic range, LOD, and specificity assays. Finally, some conclusions about LMR-based biosensors are presented, as well as future perspectives and some ideas to advance in this field.
Open Access
Comprehensive characterisation of a low-frequency-vibration energy harvester
(MDPI, 2024) Plaza Puértolas, Aitor; Iriarte Goñi, Xabier; Castellano Aldave, Jesús Carlos; Carlosena García, Alfonso; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
In this paper, we describe a measurement procedure to fully characterise a novel vibration energy harvester operating in the ultra-low-frequency range. The procedure, which is more thorough than those usually found in the literature, comprises three main stages: modelling, experimental characterisation and parameter identification. Modelling is accomplished in two alternative ways, a physical model (white box) and a mixed one (black box), which model the magnetic interaction via Fourier series. The experimental measurements include not only the input (acceleration)–output (energy) response but also the (internal) dynamic behaviour of the system, making use of a synchronised image processing and signal acquisition system. The identification procedure, based on maximum likelihood, estimates all the relevant parameters to characterise the system to simulate its behaviour and helps to optimise its performance. While the method is custom-designed for a particular harvester, the comprehensive approach and most of its procedures can be applied to similar harvesters.
Open Access
A comprehensive review of optical fiber refractometers: toward a standard comparative criterion
(Wiley, 2019) Urrutia Azcona, Aitor; Del Villar, Ignacio; Zubiate Orzanco, Pablo; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Thanks to the peculiarities of optical fiber and its ability to be combined with nanotechnology, precise and accurate measurements of the changes in optical properties (i.e., refractive index) of the medium surrounding the fiber are becoming possible with a high degree of performance. Thus, optical fiber sensors (OFSs) are increasingly finding applications in biochemistry and biomedicine. Here, all types of optical fiber refractometers are covered, and they are classified into three main groups: interferometers, grating-based structures, and resonance-based structures (the resonance is induced by coating the optical fiber sensor with a thin film). The performance of these different structures is compared by means of the most common parameters: sensitivity, full width at half minimum or maximum, figure of merit, and quality factor. The aim here is to provide a reliable and easy-to-use tool to compare the performance of the most recent developments on fiber optic refractometers.
Open Access
Data augmentation techniques for machine learning applied to optical spectroscopy datasets in agrifood applications: a comprehensive review
(MDPI, 2023) Gracia Moisés, Ander; Vitoria Pascual, Ignacio; Imas González, José Javier; Ruiz Zamarreño, Carlos; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Machine learning (ML) and deep learning (DL) have achieved great success in different tasks. These include computer vision, image segmentation, natural language processing, predicting classification, evaluating time series, and predicting values based on a series of variables. As artificial intelligence progresses, new techniques are being applied to areas like optical spectroscopy and its uses in specific fields, such as the agrifood industry. The performance of ML and DL techniques generally improves with the amount of data available. However, it is not always possible to obtain all the necessary data for creating a robust dataset. In the particular case of agrifood applications, dataset collection is generally constrained to specific periods. Weather conditions can also reduce the possibility to cover the entire range of classifications with the consequent generation of imbalanced datasets. To address this issue, data augmentation (DA) techniques are employed to expand the dataset by adding slightly modified copies of existing data. This leads to a dataset that includes values from laboratory tests, as well as a collection of synthetic data based on the real data. This review work will present the application of DA techniques to optical spectroscopy datasets obtained from real agrifood industry applications. The reviewed methods will describe the use of simple DA techniques, such as duplicating samples with slight changes, as well as the utilization of more complex algorithms based on deep learning generative adversarial networks (GANs), and semi-supervised generative adversarial networks (SGANs).
Open Access
Design and analysis of a low profile millimeter-wave band Vivaldi MIMO antenna for wearable WBAN applications
(IEEE Xplore Digital Library, 2024) Ahmad, Jawad; Hashmi, Mohammad; Bakytbekov, Azamat; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
The development of a reliable Wireless Body Area Network (WBAN) relies significantly on the quality of wearable antennas. Therefore, this paper proposes a low-profile four-element Multi-Input- Multi-Output (MIMO) antenna for wearable millimeter-wave (mm-wave) WBAN applications. The MIMO antenna structure incorporates a standardVivaldi antenna and a frequency-selective surface that encompasses the 28 GHz and 30 GHz of the mm-wave band with a 36.44% fractional bandwidth. It offers inter-element isolation of less than -20 dB in a compact space of 16 x 20 mm2. Conformability analysis, along with testing on Gustav’s model chest, hand, and leg, was evaluated in terms of the antenna impedance bandwidth, gain, efficiency, and radiation pattern. The simulated characteristics of the MIMO antenna were tested through measurements in free space and on the human body using a prototype of the antenna. Furthermore, the MIMO antenna exhibits a low envelope correlation coefficient of less than 0.24, high diversity gain of greater than 9.95 dB, and an acceptable total active reflection coefficient of less than -10 dB. To ensure safety, the Specific Absorption Rate (SAR) analysis revealed acceptable levels of 0.397 and 0.267 (W/kg) at 28 GHz and 30 GHz, respectively. The proposed MIMO design is suitable for wearable WBAN applications owing to its small size, consistent gain, and compatibility with the human body in terms of a constant impedance bandwidth and end-fire radiation pattern.
Open Access
Design of an additively-manufactured self-supported all-metal coaxial-line X-band bandpass filter
(IEEE, 2024) Pons Abenza, Alejandro; Arregui Padilla, Iván; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Martín Iglesias, Petronilo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
In this contribution, the design and manufacturing of an all-metal coaxial-line X-band bandpass filter is discussed. The device is 3D-printed as a self-supported structure without any dielectric inside the coaxial. The mechanical support between the inner and outer coaxial-line conductors is provided by means of λ/4 short-circuited stubs, which are also used in the bandpass filter design. The real transmission zeros (TZs) produced by the short-circuited stubs are responsible for a high filter selectivity. In order to enhance the filter performance, a second stage consisting in a coaxial-line stepped-impedance low-pass filter is integrated in the design to provide the rejection level required for the out-of-band behaviour. Following our design method, the bandpass and low-pass filters are designed separately, and a final matching step is performed to connect both and to achieve the aimed frequency specifications. In this way, a monoblock coaxial filter with very good in-band and out-of-band performance can by obtained by using an additive manufacturing (AM) procedure. Only the input/output (I/O) coaxial connectors will need to be assembled to the filter to perform the frequency measurements. The filters in this work can be seen as a first proposal towards more complex multi-functional monoblock structures using additively-manufactured coaxial technology, for highly-integrated RF chains. Other expected benefits beyond the compactness or lightweight are an increased RF shielding, electrostatic discharge risk reduction, and Passive Intermodulation (PIM) protection. In the paper, a prototype with a passband between 8 and 12 GHz is designed and manufactured, using a bandpass filter with three stubs and an integrated 15th-order low-pass filter, providing rejection for spurious frequencies up to 30 GHz. The filter is manufactured using Selective Laser Melting (SLM) and measurements show an excellent agreement with the simulations.
Open Access
Determination of hazardous vapors from the thermal decomposition of organochlorinated silica xerogels with adsorptive properties
(Elsevier, 2024) Rosales Reina, María Beatriz; Cruz Quesada, Guillermo; Pujol, Pablo; Reinoso, Santiago; Elosúa Aguado, César; Arzamendi Manterola, María Cruz; López Ramón, María Victoria; Garrido Segovia, Julián José; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
The incorporation of organic groups into sol-gel silica materials is known to have a noticeable impact on the properties and structure of the resulting xerogels due to the combination of the properties inherent to the organic fragments (functionality and flexibility) with the mechanical and structural stability of the inorganic matrix. However, the reduction of the inorganic content in the materials could be detrimental to their thermal stability properties, limiting the range of their potential applications. Therefore, this work aims to evaluate the thermal stability of hybrid inorganic-organic silica xerogels prepared from mixtures of tetraethoxysilane and organochlorinated triethoxysilane precursors. To this end, a series of four materials with a molar percentage of organochlorinated precursor fixed at 10%, but differing in the type of organic group (chloroalkyls varying in the alkyl-chain length and chlorophenyl), has been selected as model case study. The gases and vapors released during the thermal decomposition of the samples under N2 atmosphere have been analyzed and their components determined and quantified using a thermogravimetric analyzer coupled to a Fourier-transform infrared spectrophotometer and to a gas chromatography-mass spectrometry unit. These analyses have allowed to identify up to three different thermal events for the pyrolysis of the organochlorinated xerogel materials and to elucidate the reaction pathways associated with such processes. These mechanisms have been found to be strongly dependent on the specific nature of the organic group.
Open Access
Digital twin modelling of open category UAV radio communications: a case study
(Elsevier, 2024) Aláez Gómez, Daniel; López Iturri, Peio; Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; Falcone Lanas, Francisco; Villadangos Alonso, Jesús; Astrain Escola, José Javier; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The modeling of radio links plays a crucial role in achieving mission success of unmanned aerial vehicles (UAVs). By simulating and analyzing communication performance, operators can anticipate and address potential challenges. In this paper, we propose a full-featured UAV software-in-the-loop digital twin (SITL-DT) for a heavy-lifting hexacopter that integrates a radio link module based on an experimental path loss model for ‘Open’ category Visual Line of Sight (VLOS) conditions and drone-antenna radiation diagrams obtained via electromagnetic simulation. The main purpose of integrating and simulating a radio link is to characterize when the communication link can be conflicting due to distance, the attitude of the aircraft relative to the pilot, and other phenomena. The system architecture, including the communications module, is implemented and validated based upon experimental flight data.
Open Access
Electrospun nanofiber mats for evanescent optical fiber sensors
(Elsevier, 2013) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rivero Fuente, Pedro J.; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, a study about the optical response of electrospun nanofiber (ENF) coatings for their use in evanescent optical fiber sensors is presented. Several types of ENF mats composed of poly(acrylic acid) (PAA) were developed with different ENF diameters and densities. These ENF mats were deposited onto an optical fiber core in order to fabricate humidity evanescent optical fiber sensors. The devices were exposed to relative humidity (RH) variations from 30% RH to 95%RH. The transfer functions of the devices (transmitted optical power versus relative humidity) presented two well-differenced behaviors depending on the ENF diameter and the ENF mat density. The devices with lower ENF diameters and higher mat density showed an increase in the transmitted optical power when RH increased. On the contrary, the devices with higher ENF diameters and lower mat density showed a decrease in the transmitted optical power when RH increased. In addition to this, sensors with thinner ENF overlays, showed a higher sensitivity. In order to study the response time of these devices, the ENFs sensors were submitted to human breathing cycles and presented a response time around 340 ms (exhalation). In spite of the high RH conditions of this experiment, the devices showed a recovery time around 210 ms and a negligible hysteresis or drift with respect to the initial condition (inhalation).
Embargo
The first and second phases of the muscle compound action potential in the thumb are differently affected by electrical stimulation trains
(American Physiological Society, 2024) Lanfranchi, Clément; Rodríguez Falces, Javier; Place, Nicolas; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Sarcolemmal membrane excitability is often evaluated by considering the peak-to-peak amplitude of the compound muscle action potential (M wave). However, the first and second M-wave phases represent distinct properties of the muscle action potential, which are differentially affected by sarcolemma properties and other factors such as muscle architecture. Contrasting with previous studies in which voluntary contractions have been used to induce muscle fatigue, we used repeated electrically induced tetanic contractions of the adductor pollicis muscle and assessed the kinetics of M-wave properties during the course of the contractions. Eighteen participants (24 ± 6 yr; means ± SD) underwent 30 electrically evoked tetanic contractions delivered at 30 Hz, each lasting 3 s with 1 s intervals. We recorded the amplitudes of the first and second M-wave phases for each stimulation. During the initial stimulation train, the first and second M-wave phases exhibited distinct kinetics. The first phase amplitude showed a rapid decrease to reach ~59% of its initial value (P < 0.001), whereas the second phase amplitude displayed an initial transient increase of ~19% (P ¼ 0.007). Within subsequent trains, both the first and second phase amplitudes consistently decreased as fatigue developed with a reduction during the last train reaching ~47% of its initial value (P < 0.001). Analyzing the first M wave of each stimulation train unveiled different kinetics for the first and second phases during the initial trains, but these distinctions disappeared as fatigue progressed. These findings underscore the interplay of factors affecting the M wave and emphasize the significance of separately scrutinizing its first and second phases when assessing membrane excitability adjustments during muscle contractions.
Open Access
High frequency vibration sensor using a fiber laser with a multicore fiber interferometer
(IEEE, 2024) Correa Serrano, Ángel Ignacio; Galarza Galarza, Marko; Dauliat, Romain; Jamier, Raphael; Roy, Philippe; López-Amo Sáinz, Manuel; Pérez Herrera, Rosa Ana; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
We present an interferometric vibration sensor that uses three-core fibers. The transducer is constructed by splicing a segment 20 mm long of a multicore optical fiber (MCF) to a single-mode optical fiber (SMF). The end of the MCF segment is cut off and painted using silver metallic paint. The sensor head is operated in reflection mode. The structure is placed on a polyvinyl chloride (PVC) plate, which is excited with a wide range of frequency signals. The vibrations induce cyclic bending in the MCF segment, resulting in periodic oscillations of the reflected interference spectrum. This device is demonstrated to be suitable to measure vibrations in a frequency range of the order of 300 kHz detecting deformations as small as 0.40μm .
Open Access
Humidity sensor based on silver nanopartlcles embedded in a polymeric coating
(Sciendo, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
In this work, it is presented a novel optical fiber humidity sensor based on silver nanoparticle-loaded polymeric coatings built onto an optical fiber core. The polymeric film was fabricated using the Layer-by-Layer assembly technique. The silver nanoparticles (Ag NPs) were characterized using transmission electron microscopy (TEM and UV-VIS spectroscopy. A Localized Surface Plasmon Resonance (LSPR) attenuation band is observed when the thickness of the coating increases, and showed a very good sensitivity to Relative Humidity (RH) variations, suitable for high performance applications such as human breathing monitoring.

Browse

Browsing Artículos de revista DIEC - IEKS Aldizkari artikuluak by Department/Institute "Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza"

Results Per Page

Sort Options