INAMAT2 - Institute for Advanced Materials and Mathematics
Permanent URI for this community
Browse
Browsing INAMAT2 - Institute for Advanced Materials and Mathematics by Department/Institute "Ingeniería Mecánica, Energética y de Materiales"
Now showing 1 - 2 of 2
Results Per Page
Sort Options
Publication Open Access Characterization of two iron bullets from the royal ammunition factory of Eugi (Spain)(Technical Faculty, University of Belgrade, 2018) Zalakain Iriazabal, Iñaki; Berlanga Labari, Carlos; Álvarez Vega, Lucas; Rivero Fuente, Pedro J.; Valencia Monreal, Javier; Rodríguez Trías, Rafael; Mekanika, Energetika eta Materialen Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Mecánica, Energética y de MaterialesIn this work, a comparative analysis of two iron bullets found in The Royal Ammunition Factory of Eugi in Navarra (Spain) was performed. Both bullets presented a spherical shape with a relatively good state of preservation, belonging to the last years of the factory production (1766-1850). Several techniques such as microhardness, X-ray fluorescence (XRF), light (LM) and scanning electron microscopy (SEM), optical mission spectroscopy (OES) and energy dispersive X-ray spectroscopy (EDX) analysis were used in order to identify the manufacturing process of the two bullets. The analyses of the microstructures carried out by LM and SEM showed that one bullet was composed of white cast iron with a pearlitic matrix, steadite and graphite; while the other was composed of grey cast iron with a pearlitic matrix, graphite and a low amount of steadite. The chemical analysis of the bullets carried out by OES indicated significant differences in the amount of silicon and phosphorous. The variation in silicon content could suggest that the foundry temperature under oxidizing environment varied during the casting. The SEM and EDX analyses showed both bullets had manganese sulphide inclusions but only one of the bullets exhibited titanium and vanadium inclusions. The microhardness analyses carried out revealed Vickers hardness differences along the diameter. This variation could be explained by the differences in cooling rate along the diameter. Based on the physical characteristics of the bullets and on the obtained results, it can be concluded that one of the bullets could have been used as a grapeshot projectile and the other one as a bullet for ribauldequins. In addition, calcined ore and slag found in this factory were also analysed. The variation found in their chemical composition corroborated that the foundry temperature employed during the manufacturing process was low, the slag being enriched in Si, Al and Mn elements.Publication Open Access Effect of the temperature in the mechanical properties of austenite, ferrite and sigma phases of duplex stainless steels using hardness, microhardness and nanoindentation techniques(MDPI, 2017) Argandoña Salinas, Gorka; Palacio, José F.; Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Rivero Fuente, Pedro J.; Peña, Julio; Rodríguez Trías, Rafael; Mekanika, Energetika eta Materialen Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Mecánica, Energética y de MaterialesThe aim of this work is to study the hardness of the ferrite, austenite and sigma phases of a UNS S32760 superduplex stainless steel submitted to different thermal treatments, thus leading to different percentages of the mentioned phases. A comparative study has been performed in order to evaluate the resulting mechanical properties of these phases by using hardness, microhardness and nanoindentation techniques. In addition, optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD) have been also used to identify their presence and distribution. Finally, the experimental results have shown that the resulting hardness values were increased as a function of a longer heat treatment duration which it is associated to the formation of a higher percentage of the sigma phase. However, nanoindentation hardness measurements of this sigma phase showed lower values than expected, being a combination of two main factors, namely the complexity of the sigma phase structure as well as the surface finish (roughness).