Artículos de revista ISC - ISC aldizkari artikuluak
Permanent URI for this collection
Browse
Browsing Artículos de revista ISC - ISC aldizkari artikuluak by Subject "5G"
Now showing 1 - 9 of 9
Results Per Page
Sort Options
Publication Open Access 5G spatial modeling of personal RF-EMF assessment within aircrafts cabin environments(IEEE, 2022) Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; Rodríguez Corbo, Fidel Alejandro; López Iturri, Peio; Shubair, Raed M.; Ramos González, Victoria; Falcone Lanas, Francisco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónRecently, new wireless communication systems within aircrafts cabins have drawn higher attention due to the growing demand of passenger services and applications and their corresponding requirements and constraints. In this regard, the fifth generation (5G) of wireless communication becomes an attractive and promising alternative to enable aircraft passengers' comfort and entertainment along the flight, considering its potential benefits in term of high data transfers and low latencies. Nevertheless, general population concern about radio frequency electromagnetic fields (RF-EMF) safety in general and, in particular to the environmental exposure at which we are all exposed in these flights, increases at the same time. Thus, in this work, we present an experimental campaign of measurements for current passengers' environmental exposure assessment, performed in different real generalizable type of flights and aircrafts' cabins, in order to provide current RF-EMF exposure insight within these complex heterogeneous environments. In addition, worst-case uplink 5G scenarios, where all 5G cellular handsets of the passengers operate at the same time, have been simulated by means of an in-house developed 3D Ray Launching (3D-RL) deterministic technique. Before takeoff and after landing, critical scenarios with the aircrafts' doors closed have been selected and assessed considering different types of modeled aircrafts full of passengers, considering 5G frequency range 2 (5G-FR2) operating links. The obtained results show that the operation frequency and the morphology and topology of the aircraft cabin have a great influence in the environmental RF-EMF passengers' spatial distribution and overall exposure, but not exceeding, even in worst case conditions, the international established regulatory limits. © 2022 IEEE.Publication Open Access Broadband 3-D shared aperture high isolation nine-element antenna array for on-demand millimeter-wave 5G applications(Elsevier, 2022) Alibakhshikenari, Mohammad; Virdee, Bal S.; Vadalà, Valeria; Dalarsson, Mariana; Cos Gómez, María Elena de; Alharbi, Abdullah G.; Burokur, Shah Nawaz; Aïssa, Sonia; Dayoub, Iyad; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónThe paper presents the results of a novel 3-D shared aperture 3 × 3 matrix antenna-array for 26 GHz band 5 G wireless networks. Radiation elements constituting the array are hexagonal-shaped patches that are elevated above the common dielectric substrate by 3.35 mm and excited through a metallic rod of 0.4 mm diameter. The rod protrudes through the substrate of 0.8 mm thickness. It is shown that by isolating each radiating element in the array with a wall suppresses unwanted electromagnetic (EM) wave interactions, resulting in improvement in the antenna’s impedance matching and radiation characteristics. Moreover, the results show that by embedding hexagonalshaped slots in the patches improve the antenna’s gain and radiation efficiency performance. The subwavelength length slots in the patches essentially transform the radiating elements to exhibit metasurface characteristics when the array is illuminated by EM-waves. The proposed array structure has an average gain and radiation efficiency of 20 dBi and 93%, respectively, across 24.0–28.4 GHz. The isolation between its radiation elements is greater than 22 dB. Compared to the unslotted array the improvement in isolation between radiating elements is greater than 11dB, and the gain and efficiency are better than 10.5 dBi, and 25%, respectively. The compact array has a fractional bandwidth of 16% and a form factor of 20 × 20 × 3.35 mm3.Publication Open Access Fifth-generation (5G) mmwave spatial channel characterization for urban environments’ system analysis(MDPI, 2020) Azpilicueta Fernández de las Heras, Leyre; López Iturri, Peio; Zuñiga Mejia, Jaime; Aguirre Gallego, Erik; Falcone Lanas, Francisco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónIn this work, the channel characterization in terms of large-scale propagation, small-scale propagation, statistical and interference analysis of Fifth-Generation (5G) Millimeter Wave (mmWave) bands for wireless networks for 28, 30 and 60 GHz is presented in both an outdoor urban complex scenario and an indoor scenario, in order to consider a multi-functional, large node-density 5G network operation. An in-house deterministic Three-Dimensional Ray-Launching (3D-RL) code has been used for that purpose, considering all the material properties of the obstacles within the scenario at the frequency under analysis, with the aid of purpose-specific implemented mmWave simulation modules. Different beamforming radiation patterns of the transmitter antenna have been considered, emulating a 5G system operation. Spatial interference analysis as well as time domain characteristics have been retrieved as a function of node location and configuration.Publication Open Access From 2G to 5G spatial modeling of personal RF-EMF exposure within urban public trams(IEEE, 2020) Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; Karpowicz, Jolanta; López Iturri, Peio; Falcone Lanas, Francisco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónThe upcoming design and implementation of the new generation of 5G cellular systems, jointly with the multiple wireless communication systems that nowadays coexist within vehicular environments, leads to Heterogeneous Network challenging urban scenarios. In this framework, user's Radiofrequency Electromagnetic Fields (RF-EMF) radiation exposure assessment is pivotal, to verify compliance with current legislation thresholds. In this work, an in-depth study of the E-field characterization of the personal mobile communications within urban public trams is presented, considering different cellular technologies (from 2G to 5G). Specifically, frequency bands in the range of 5G NR frequency range 1 (FR1) and millimeter wave (mm-wave) bands within frequency range 2 (FR2) have been analyzed for 5G scenarios, considering their dispersive material properties. A simulation approach is presented to assess user mobile phone base station up-link radiation exposure, considering all the significant features of urban transportation trams in terms of structure morphology and topology or the materials employed. In addition, different user densities have been considered at different frequency bands, from 2G to 5G (FR1 and FR2), by means of an in-house developed deterministic 3D Ray-Launching (3D-RL) technique in order to provide clear insight spatial E-field distribution, including the impact in the use of directive antennas and beamforming techniques, within realistic operation conditions. Discussion in relation with current exposure limits have been presented, showing that for all cases, E-Field results are far below the maximum reference levels established by the ICNIRP guidelines. By means of a complete E-field campaign of measurements, performed with both, a personal exposimeter (PEM) and a spectrum analyzer within a real tram wagon car, the proposed methodology has been validated showing good agreement with the experimental measurements. In consequence, a simulation-based analysis methodology for dosimetry estimation is provided, aiding in the assessment of current and future cellular deployments in complex heterogeneous vehicular environments.Publication Open Access Metamaterials and their application in the performance enhancement of reconfigurable antennas: a review(MDPI, 2023) Hussain, Musa; Awan, Wahaj Abbas; Alzaidi, Mohammed S.; Hussain, Niamat; Ali, Esraa Mousa; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio IngeniaritzarenMetamaterials exhibit properties in terms of subwavelength operation or phase manipulation, among others, that can be used in a variety of applications in 5G communication systems. The future and current 5G devices demand high efficiency, high data rate, computational capabilities, cost-effectiveness, compact size, and low power consumption. This variation and advancement are possible when the antenna design is revised to operate over wideband, high gain, and multiband and has characteristics of compact size, reconfiguration, absorption, and simple ease of fabrication. The materials loaded with antennas or, in the same cases, without antennas, offer the aforementioned characteristics to bring advancement in order to facilitate users. A number of works on designing metasurfaces capable of improving bandwidth, gain efficiency, and reducing the size and cost of antennas are available in the literature for this purpose. Not only are these applications possible, but the intelligent metasurfaces are also designed to obtain reconfiguration in terms of frequency and polarization. The number of absorbers loaded with metamaterials is also designed to improve the absorption percentage used for radar applications. Thus, in this paper, the general overview of different types of metamaterials and their role in performance enhancement and application in 5G and 6G communication systems is discussed.Publication Open Access Metasurface-based wideband MIMO antenna for 5G millimeter-wave systems(IEEE, 2021) Sehrai, Daniyal Ali; Asif, Muhammad; Shah, Wahab Ali; Khan, Jalal; Ullah, Ibrar; Ibrar, Muhammad; Jan, Saeedullah; Alibakhshikenari, Mohammad; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónThis paper presents a metasurface based multiple-input multiple-output (MIMO) antenna with a wideband operation for millimeter-wave 5G communication systems. The antenna system consists of four elements placed with a 90 degree shift in order to achieve a compact MIMO system while a 2× 2 non-uniform metasurface (total four elements) is placed at the back of the MIMO configuration to improve the radiation characteristics of it. The overall size of the MIMO antenna is 24× 24 mm2 while the operational bandwidth of the proposed antenna system ranges from 23.5-29.4 GHz. The peak gain achieved by the proposed MIMO antenna is almost 7dB which is further improved up to 10.44 dB by employing a 2× 2 metasurface. The total efficiency is also observed more than 80% across the operating band. Apart from this, the MIMO performance metrics such as envelope correlation coefficient (ECC), diversity gain (DG), and channel capacity loss (CCL) are analyzed which demonstrate good characteristics. All the simulations of the proposed design are carried out in computer simulation technology (CST) software, and measured results reveal good agreement with the simulated one which make it a potential contender for the upcoming 5G communication systems.Publication Open Access A radio channel model for D2D communications blocked by single trees in forest environments(MDPI, 2019) Picallo Guembe, Imanol; Klaina, Hicham; López Iturri, Peio; Aguirre Gallego, Erik; Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; Eguizábal Garrido, Alejandro; Falcone Lanas, Francisco; Alejos, Ana V.; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónIn this paper we consider the D2D (Device-to-Device) communication taking place between Wireless Sensor Networks (WSN) elements operating in vegetation environments in order to achieve the radio channel characterization at 2.4 GHz, focusing on the radio links blocked by oak and pine trees modelled from specimens found in a real recreation area located within forest environments. In order to fit and validate a radio channel model for this type of scenarios, both measurements and simulations by means of an in-house developed 3D Ray Launching algorithm have been performed, offering as outcomes the path loss and multipath information of the scenarios under study for forest immersed isolated trees and non-isolated trees. The specific forests, composed of thick in-leaf trees, are called Orgi Forest and Chandebrito, located respectively in Navarre and Galicia, Spain. A geometrical and dielectric model of the trees were created and introduced in the simulation software. We concluded that the scattering produced by the tree can be divided into two zones with different dominant propagation mechanisms: an obstructed line of sight (OLoS) zone far from the tree fitting a log-distance model, and a diffraction zone around the edge of the tree. 2D planes of delay spread value are also presented which similarly reflects the proposed two-zone model.Publication Open Access Towards environmental RF-EMF assessment of mmwave high-node density complex heterogeneous environments(MDPI, 2021) Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; Rodríguez Corbo, Fidel Alejandro; López Iturri, Peio; Ramos González, Victoria; Alibakhshikenari, Mohammad; Shubair, Raed M.; Falcone Lanas, Francisco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónThe densification of multiple wireless communication systems that coexist nowadays, as well as the 5G new generation cellular systems advent towards the millimeter wave (mmWave) frequency range, give rise to complex context-aware scenarios with high-node density heterogeneous networks. In this work, a radiofrequency electromagnetic field (RF-EMF) exposure assessment from an empirical and modeling approach for a large, complex indoor setting with high node density and traffic is presented. For that purpose, an intensive and comprehensive in-depth RF-EMF E-field characterization study is provided in a public library study case, considering dense personal mobile communications (5G FR2 @28 GHz) and wireless 802.11ay (@60 GHz) data access services on the mmWave frequency range. By means of an enhanced in-house deterministic 3D ray launching (3D-RL) simulation tool for RF-EMF exposure assessment, different complex heterogenous scenarios of high complexity are assessed in realistic operation conditions, considering different user distributions and densities. The use of directive antennas and MIMO beamforming techniques, as well as all the corresponding features in terms of radio wave propagation, such as the body shielding effect, dispersive material properties of obstacles, the impact of the distribution of scatterers and the associated electromagnetic propagation phenomena, are considered for simulation. Discussion regarding the contribution and impact of the coexistence of multiple heterogeneous networks and services is presented, verifying compliance with the current established international regulation limits with exposure levels far below the aforementioned limits. Finally, the proposed simulation technique is validated with a complete empirical campaign of measurements, showing good agreement. In consequence, the obtained datasets and simulation estimations, along with the proposed RF-EMF simulation tool, could be a reference approach for the design, deployment and exposure assessment of the current and future wireless communication technologies on the mmWave spectrum, where massive high-node density heterogeneous networks are expected.Publication Open Access Validation of 3D simulation tool for radio channel modeling at 60 GHz: a meeting point for empirical and simulation-based models(Elsevier, 2020) Celaya Echarri, Mikel; Azpilicueta Fernández de las Heras, Leyre; López Iturri, Peio; Falcone Lanas, Francisco; García Sánchez, Manuel; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio IngeniaritzarenThe radio channel modelling of the millimeter wave bands for the fifth generation of wireless mobile communications, appears as a challenge for both empirical and simulation approaches. In this paper we discuss the use of experimental datasets for validation of a simulation tool based on deterministic 3D ray-launching technique. The goal it twofold: validating the simulation tool and achieving more consistent results considering the restrictions and performance limits of hardware elements. A microcell canyon street scenario has been chosen for interleaving ray launching prediction and empirical analysis. Simulation results such as received power or angular distribution of path loss, as well as channel dispersion parameters such as root-mean-square delay spread have been presented. In addition, the line-of-sight to non-line-of-sight transition has been modeled as a result of the empirical-simulation interaction. Comparison of simulation and measurement results for the proposed microcellular urban scenario exhibit good agreement, validating the proposed methodology. (C) 2020 Elsevier Ltd. All rights reserved.