Person:
Gómez Laso, Miguel Ángel

Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Gómez Laso

First Name

Miguel Ángel

person.page.departamento

ORCID

0000-0003-1371-0610

person.page.upna

2553

Name

Filters

2020 - 202420
Reset filters

Settings

Start date: 2020 ×

Search Results

Now showing 1 - 10 of 20
  • Thumbnail Image
    PublicationOpen Access
    Integración de múltiples stubs en filtros de saltos de impedancias de alta selectividad
    (URSI, 2023) Gómez Laso, Miguel Ángel; Sami, Abdul; Lopetegui Beregaña, José María; Martin Iglesias, Petronilo; Álvarez Botero, Germán Andrés; Pons Abenza, Alejandro; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    Rectangular waveguide commensurate-line stepped-impedance bandpass filters have been shown to have an increased fabrication robustness using conventional CNC milling. In this paper, their frequency response is improved by adding multiple transmission zeros at fully-controlled positions around the passband. The technique starts with the design of the filter without transmission zeros and only requires that one of the filter sections is slightly redesigned, while the rest keep unaltered, when lambda_g/¿¿ and 3*lambda_g/¿¿ stubs are included in the section to increase the overall filter selectivity around the passband. The design example is a 7th-order Chebyshev bandpass filter in Ku-band.
  • Thumbnail Image
    PublicationOpen Access
    The Canfranc Axion Detection Experiment (CADEx): search for axions at 90 GHz with Kinetic Inductance Detectors
    (IOP Publishing, 2022) Aja, Beatriz; Arguedas Cuendis, Sergio; Arregui Padilla, Iván; Artal, Eduardo; Barreiro, R. Belén; Casas, Francisco J.; Ory, Marina C. de; Díaz-Morcillo, Alejandro; Fuente, Luisa de la; Gallego, Juan Daniel; García-Barceló, José María; Gimeno, Benito; Gómez, Alicia; Granados, Daniel; Kavanagh, Bradley J.; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Lozano-Guerrero, Antonio José; Magaz, María T.; Martín-Pintado, Jesús; Martínez-González, Enrique; Miralda-Escudé, Jordi; Monzó-Cabrera, Juan; Najarro de la Parra, Francisco; Navarro-Madrid, José R.; Nuñez Chico, Ana B.; Pascual, Juan Pablo; Pelegrin, Jorge; Peña Garay, Carlos; Rodríguez, David; Socuéllamos, Juan M.; Teberio Berdún, Fernando; Teniente Vallinas, Jorge; Vielva, Patricio; Vila, Iván; Vilar, Rocío; Villa, Enrique; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    We propose a novel experiment, the Canfranc Axion Detection Experiment (CADEx), to probe dark matter axions with masses in the range 330–460 μeV, within the W-band (80–110 GHz), an unexplored parameter space in the well-motivated dark matter window of Quantum ChromoDynamics (QCD) axions. The experimental design consists of a microwave resonant cavity haloscope in a high static magnetic field coupled to a highly sensitive detecting system based on Kinetic Inductance Detectors via optimized quasi-optics (horns and mirrors). The experiment is in preparation and will be installed in the dilution refrigerator of the Canfranc Underground Laboratory. Sensitivity forecasts for axion detection with CADEx, together with the potential of the experiment to search for dark photons, are presented.
  • Thumbnail Image
    PublicationOpen Access
    Integrating multiple stubs in stepped-impedance filter aiming for high selectivity
    (IET, 2022) Sami, Abdul; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arnedo Gil, Israel; Calero Fernández, Ibai; Teberio Berdún, Fernando; Martín Iglesias, Petronilo; Benito Pertusa, David; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband.
  • Thumbnail Image
    PublicationOpen Access
    Assessment of performance of one-turn inductors in series configuration through a transmission-line modeling approach
    (IEEE , 2024) Álvarez Botero, Germán Andrés; Moctezuma-Pascual, Eduardo; Gómez Laso, Miguel Ángel; Torres-Torres, Reydezel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza
    In this paper, transmission-line theory is applied to implement a physical model for compact one-turn inductors, which simultaneously incorporates the frequency-dependent effects introduced by the conductor skin effect and the loss originated by the coupling with the ground plane. For this purpose, S-parameter measurements are processed to extract the associated parameters, which exhibit scalability with the turn radius. This allows the model to be used for interpolation and extrapolation analyses. In this regard, the device performance is assessed for one-turn inductors in series connection, for different load impedances, and when the turn is narrowed. To validate the proposal, agreement between the model and the experimental transmission line RLGC parameters, the return loss, and the Q-factor is obtained up to 20 GHz.
  • Thumbnail Image
    PublicationOpen Access
    Multipactor breakdown analysis of Ku-band meandered low-pass filter
    (2022) Sami, Abdul; Teberio Berdún, Fernando; Arnedo Gil, Israel; Martín Iglesias, Petronilo; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    In this work, a very compact rectangular waveguide low-pass filter with meandered topology based on commensurate lines for Ku-band satellite applications is analysed for high-power handling capabilities. The device consists of rectangular waveguide sections properly cascaded to form a meandered topology to obtain the desired value of the local reflection coefficients. which are essential to achieve the target frequency response and also to keep large mechanical gaps. Hence, this technique allows us not only to design a filter with compact size but a filter geometry which is suitable for high power applications. In the paper, the low-pass filter based on commensurate lines is first designed by cascading E-plane mitered bends (±90° EMBs) in CST Microwave Studio (MWS) and then the values of the electromagnetic fields at the passband frequencies are exported to Spark3D to perform a multipactor analysis. The critical areas inside the device where the multipactor discharge occurs will also be identified in the high-power analysis. https://doi.org/10.5281/zenodo.7343236
  • Thumbnail Image
    PublicationOpen Access
    Filtro paso banda en tecnología groove gap waveguide con altura de pines reducida para facilitar su fabricación
    (Universidad de Málaga, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    In this work, a novel topology of groove gap waveguide (GGW) technology is presented to facilitate the fabrication process by Computer Numerical Control (CNC) milling. GGW has been proposed as an interesting alternative to the rectangular waveguide for the design of microwave and millimeter-wave components. This technology consists of two parallel metal plates, where one of them has a (lambda)/4-height pin bed that provides a high impedance condition at the plane over the pins, avoiding electrical contact requirement with the upper plate and hence facilitating the fabrication requirements. However, the manufacture by CNC milling of the pins may be troublesome, especially for devices operating at high frequency. A way to facilitate this process is achieved by using pins with reduced height. Moreover, the proposed configuration allows us to maintain the standard dimension ports of the equivalent rectangular waveguide and the operation in its corresponding bandwidth. A comparison with other GGW topologies has been presented and a bandpass filter has been fabricated to validate its usefulness.
  • Thumbnail Image
    PublicationOpen Access
    Gap waveguide topology with reduced height pins for millimeter-wave components
    (URSI Publications, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    A new topology for groove gap waveguide (GGW) technology is proposed to ease its manufacturing process by computer numerical control (CNC) milling. GGW technology consists of two metal plates, where one of them presents a λ/4 height pin bed that avoids contact with the other plate, making it an ideal alternative to other waveguides for millimeterwave applications. However, the manufacture of the pins by CNC milling may be troublesome due to the large pin height required. A GGW with reduced height pins will be proposed, maintaining the standard dimensions of the equivalent rectangular waveguide ports and the operation bandwidth. The performance of this new topology will be compared with other proposals by means of simulations and measurements, and a bandpass filter will be also implemented and manufactured in this technology to validate its usefulness.
  • Thumbnail Image
    PublicationOpen Access
    W-band filtering antenna based on a slot array and stacked coupled resonators using gap waveguide technology
    (IEEE, 2024) Santiago Arriazu, David; Fang, Mu; Zaman, Ashraf Uz; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
    This letter proposes a new design approach for filtering antennas. The novel matching reflection coefficient based method allows the integration of filters and antennas without compromising the frequency behavior of either of these components. Moreover, this integration is done avoiding the need of lengthy optimization processes and provides a high degree of flexibility in the types of antennas that can be used. In order to validate it, two examples are provided. In both cases, a 4 th -order Chebyshev bandpass filter at 101.5 GHz implemented in stacked groove gap waveguide (GGW) configuration is used, firstly along with a single aperture antenna and, subsequently, with a slotted ridge gap waveguide (RGW) array. This second example has been manufactured to demonstrate the usefulness of the new design methodology. Excellent measured performance has been obtained for a filtering antenna at W-band for the first time.
  • Thumbnail Image
    PublicationOpen Access
    High-power filter design in waveguide technology: future generation of waveguide satellite filters in payloads handling increasing bit rates and numbers of channels
    (IEEE, 2020) Arregui Padilla, Iván; Teberio Berdún, Fernando; Arnedo Gil, Israel; Percaz Ciriza, Jon Mikel; Martín Iglesias, Petronilo; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    To design a filter for a particular application, many issues must first be considered. Which technology will be the most convenient? What design technique will provide better results for a particular set of frequency specifications? Once the device has been designed, will it fulfill all of the (not only electrical) requirements? It is not always easy to answer such questions in advance. In this article, we try to shed some light on these questions when our aim is the design of filters for high-power operation.
  • Thumbnail Image
    PublicationOpen Access
    Metal 3D printing for RF/microwave high-frequency parts
    (Springer, 2022) Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Teberio Berdún, Fernando; Arregui Padilla, Iván; Marechal, M.; Calves, P.; Hazard, M.; Pambaguian, L.; Brandao, A.; Rodríguez Castillo, S.; Martin, T.; Percaz Ciriza, Jon Mikel; Iza, V.; Martín-Iglesias, Santiago; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    Space Systems have been historically characterised by high performance, high reliability and high cost. Every new generation of space systems tends to improve performance, keep as much as possible reliability, speeding the lead time and lower the cost. Aggressive approach is nowadays followed by some of the players of the new space ecosystem where, for instance, reli- ability can be relaxed thanks for the in-orbit redundancy or robustness to failures by having a constellation with a high number of satellites. This push towards the technology and system limit requires to investigate new methods for the manufacturing of RF/Microwave parts. RF devices such as those based on waveguide structures, benefit from an additive manufacturing approach in terms of radio frequency (RF) performance and compactness. However each manufacturing approach comes with specific features and limitations which need to be well understood and, in some cases, even taking advantage of them. This paper provides a short review of some of the RF/Microwave parts already manufactured using this technology. The paper will focus mainly on metal 3D printing parts since this technology is, at the moment, well accepted by the space community.