Person:
Gómez Laso, Miguel Ángel

Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Gómez Laso

First Name

Miguel Ángel

person.page.departamento

ORCID

0000-0003-1371-0610

person.page.upna

2553

Name

Filters

2019 - 201912020 - 20222
Reset filters

Settings

Subject: Waveguide ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    PublicationOpen Access
    Metal 3D printing for RF/microwave high-frequency parts
    (Springer, 2022) Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Teberio Berdún, Fernando; Arregui Padilla, Iván; Marechal, M.; Calves, P.; Hazard, M.; Pambaguian, L.; Brandao, A.; Rodríguez Castillo, S.; Martin, T.; Percaz Ciriza, Jon Mikel; Iza, V.; Martín-Iglesias, Santiago; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    Space Systems have been historically characterised by high performance, high reliability and high cost. Every new generation of space systems tends to improve performance, keep as much as possible reliability, speeding the lead time and lower the cost. Aggressive approach is nowadays followed by some of the players of the new space ecosystem where, for instance, reli- ability can be relaxed thanks for the in-orbit redundancy or robustness to failures by having a constellation with a high number of satellites. This push towards the technology and system limit requires to investigate new methods for the manufacturing of RF/Microwave parts. RF devices such as those based on waveguide structures, benefit from an additive manufacturing approach in terms of radio frequency (RF) performance and compactness. However each manufacturing approach comes with specific features and limitations which need to be well understood and, in some cases, even taking advantage of them. This paper provides a short review of some of the RF/Microwave parts already manufactured using this technology. The paper will focus mainly on metal 3D printing parts since this technology is, at the moment, well accepted by the space community.
  • Thumbnail Image
    PublicationOpen Access
    General synthesis of tapered matching sections for single mode operation using the coupled-mode theory
    (IEEE, 2019) Percaz Ciriza, Jon Mikel; Arnedo Gil, Israel; Arregui Padilla, Iván; Teberio Berdún, Fernando; Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    In this paper, a novel and general method to synthetize microwave waveguide tapers intended for single mode operation is proposed. The technique is based on the use of an exact series solution of the inverse scattering synthesis problem. An additional strategy necessary for dealing with waveguides where the propagation constant varies with the position is included. The coupled-mode theory is employed to model the electromagnetic behavior of the taper with the inherent mismatch caused by the connection of the waveguides with different cross-sections. The novel method allows us to synthesize the (classical) transmission line taper functions of Klopfenstein and Hecken, making them suitable for general waveguide tapers with single mode operation. Additionally, a new type of taper functions, also suitable for general waveguide tapers, is presented. The novel functions are obtained by partially employing the frequency response of multisection transformers, resulting in fully smooth tapers that can offer shorter lengths than the classical proposals. The taper synthesis procedure is demonstrated in rectangular waveguide technology, by requiring realistic and challenging specifications for different cases with different waveguide cross-sections to be matched: height mismatch, width mismatch, and simultaneous height and width mismatch. Several prototypes of Klopfenstein, Hecken and novel function tapers have been fabricated in an aluminum alloy by means of an Additive Manufacturing technique (Direct Metal Laser Sintering). The simulation and measurement results obtained for the rectangular waveguide taper prototypes confirm the accuracy of the novel synthesis technique proposed.
  • Thumbnail Image
    PublicationOpen Access
    High-yield waveguide diplexer for low-cost E-band 5G point-to-point radio links
    (IEEE, 2022) Teberio Berdún, Fernando; Calero Fernández, Ibai; Arregui Padilla, Iván; Martín Iglesias, Petronilo; Teniente Vallinas, Jorge; Gómez Laso, Miguel Ángel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    This paper presents the design and realization of a high-yield tuning-less waveguide diplexer and a high-gain lens horn antenna for 5G point-to-point fixed-beam communications at the frequency ranges of 71/76 GHz and 81/86 GHz (E-band). The diplexer is composed of two bandpass filters based on the combination of a low-pass filtering function and a high-pass structure. The diplexer provides very relaxed fabrication tolerances. A prototype has been fabricated and measured showing return loss better than 20 dB and attenuation levels higher than 60 dB. The insertion loss is better than 1 dB. A lens horn antenna which provides more than 38 dBi gain is utilized to provide high directivity at the same frequencies. The proposed sub-system combines the advantages of high-performance and simple mechanical assembly finding, it especially attractive for 5G applications due to the reduced fabrication cost.