Open Access
Aluminum coated fiber optic sensor for enhancing flow rate measurement
(SPIE, 2023) Rodríguez Rodríguez, Armando; Urroz Unzueta, José Carlos; Diéguez Elizondo, Pedro; Bravo Acha, Mikel; López-Amo Sáinz, Manuel; López Rodríguez, José Javier; Ingeniería; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A water flow and velocity aluminum-coated Fiber Bragg Grating sensor system for open channels was designed, simulated and tested. The sensing head was designed, ruggedized and customized to measure velocities at different depths, in order to calculate the discharge in open channels. This paper shows, for the first time to our knowledge, the simulation of such kind of fiber sensors in open channels.
Open Access
Low noise dual-wavelength erbium fiber laser in single-longitudinal-mode operation
(Springer, 2012) Rota Rodrigo, Sergio; Pérez Herrera, Rosa Ana; Fernández Vallejo, Montserrat; López-Amo Sáinz, Manuel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
A new stable dual-wavelength fiber-ring laser based on erbium-doped fiber amplification is reported. The laser is based on ring resonators and employs fiber Bragg gratings to select the operation wavelengths. The topology of the laser has a significant influence in its performance: allowing an independent control of the losses for both lasing wavelengths and achieving a low noise configuration. As a result, it is experimentally demonstrated that both emission lines work in single-longitudinal-mode operation and the topology offers a better stability and higher optical signalto-noise ratios than similar configurations.
Open Access
Concrete beam bending test monitorization using a high strain fiber optic sensor
(IEEE / OSA, 2012) Bravo Acha, Mikel; Sáenz, J.; Bravo Navas, M.; López-Amo Sáinz, Manuel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this work the development of an 'eight-shape' fiber optic sensor for high strain measurement is experimentally demonstrated. This strain sensor is interrogated using a commercial optical time domain reflectometer through a dual configuration that is able to measure backscattering and the transmission of an intensity pulse while reducing unwanted cladding-mode coupling effects. An 'in field' concrete beam bending test was also performed in order to compare the proposed low-cost intensity bending sensor with the mature fiber Bragg grating technology.
Open Access
One-year analysis of road condition using FBG arrays
(SPIE, 2023) Corera Orzanco, Íñigo; Pradas Martínez, Javier; Leandro González, Daniel; Bravo Acha, Mikel; López-Amo Sáinz, Manuel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA06-2022
In this work, it is presented an analysis of FBG arrays installed in a public road. The arrays were installed in a newly paved urban road and were monitored for more than one year. The study evidences the permanent deformation of the wearing course and the degradation of the reflected spectra of the sensors.
Open Access
Micro-drilled optical fiber for enhanced laser strain sensors
(SPIE, 2019) Pérez Herrera, Rosa Ana; Bravo Acha, Mikel; Roldán Varona, Pablo; Leandro González, Daniel; Rodríguez Cobo, Luis; López Higuera, José Miguel; López-Amo Sáinz, Manuel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, we present an experimental measurement of temperature and strain sensitivities of a micro-drilled optical fiber (MDOF). The MDOF consisted of a quasi-randomly distributed reflector along a single mode fiber (SMF). A fiber cavity laser based on MDOF was experimentally studied, attaining a single-wavelength laser emission centered at 1568.6nm. The output power level obtained from this single-laser oscillation when pumped at 140mW was around - 9.6dBm, and an optical signal to noise ratio (OSNR) of around 45dB was measured. Although temperature sensitivities of fiber Bragg gratings used as sensors are similar to our MDOF, strain sensitivity is enhanced around one order of magnitude when the MDOF was used.
Open Access
Design of optical fiber Bragg grating-based sensors for flow measurement in pipes
(Taylor & Francis, 2023) Diéguez Elizondo, Pedro; Rodríguez Rodríguez, Armando; Urroz Unzueta, José Carlos; López Rodríguez, José Javier; López-Amo Sáinz, Manuel; Ingeniería; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work, optical Fiber Bragg grating (FBG) sensors were used to measure water flow in pipes. Several types of coatings were incorporated into the design of the sensors to examine their effects on the elastic strain that the fiber underwent as a result of the water flow. ANSYS-CFX V2020 R2 software was used to model the elastic strain encountered by the fiber under various flow rates in order to assess the performance of the FBG sensors. The calculations and experimental data exhibited good convergence, demonstrating the accuracy of the FBG sensors in determining water flow. These calculations and procedures can be extrapolated to any other fluid.
Open Access
Optical power-based interrogation of plasmonic tilted fiber Bragg grating biosensors
(SPIE, 2017) González Vila, Á.; López Aldaba, Aitor; Kinet, D.; Mégret, P.; López-Amo Sáinz, Manuel; Caucheteur, C.; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Two interrogation techniques for plasmonic tilted fiber Bragg grating sensors are reported and experimentally tested. Typical interrogation methods are usually based on tracking the wavelength shift of the most sensitive cladding mode, but for biosensing applications, spectrometer-based methods can be replaced by more efficient solutions. The proposed techniques thus rely on the measurement of the induced changes in optical power. The first one consists of a properly polarized tunable laser source set to emit at the wavelength of the sensor most sensitive mode and an optical power meter to measure the transmitted response. For the second method, a uniform fiber Bragg grating is photo-inscribed beyond the sensor in such a way that its central wavelength matches the sensor most sensitive mode, acting as an optical filter. Using a LED source, light reflected backwards by this grating is partially attenuated when passing through the sensor due to plasmon wave excitation and the power changes are quantified once again with an optical power meter. A performance analysis of the techniques is carried out and they both result competitive interrogation solutions. The work thus focuses on the development of cost-effective alternatives for monitoring this kind of biosensors in practical situations.
Open Access
Dual-wavelength single-longitudinal-mode erbium fiber laser for temperature measurements
(SPIE, 2014) Díaz Lucas, Silvia; López-Amo Sáinz, Manuel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
A dual-wavelength erbium fiber laser with single-longitudinal-mode characteristic is proposed and demonstrated. The system uses a 7-m-long highly doped erbium-doped fiber as the primary gain medium while two fiber Bragg gratings (FBGs) act as a wavelength selection mechanism. The sensing capability of the FBGs gives this source the possibility to be also used in a dual-sensor multiplexing scheme. The system is very stable and suitable for sensor multiplexing.
Open Access
Polyaniline deposition on tilted fiber Bragg grating for pH sensing
(SPIE, 2017) López Aldaba, Aitor; González Vila, Á.; Debliquy, M.; López-Amo Sáinz, Manuel; Caucheteur, C.; Lahem, D.; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, we present the results of a new pH sensor based on a polyaniline (PAni) coating on the surface of a tilted fiber Bragg grating. The pH-sensitive PAni was deposited by in situ chemical oxidative polymerization. The performance of the fabricated pH sensor was tested and the obtained pH values were compared with the results obtained using a pH meter device. It was found that the sensor exhibits response to pH changes in the range of 2-12, achieving a sensitivity of 46 pm/pH with a maximum error due to the hysteresis effect of ±1.14 pH. The main advantages of this PAni-TFBG pH sensor are biochemical compatibility, temperature independence, long-term stability and remote real-time multipoint sensing features. This type of sensor could be used for biochemical applications, pipeline corrosion monitoring or remote-multipoint measurements.
Open Access
Power over fiber system for heterogeneous sensors multiplexing
(IEEE, 2024-06-12) Rodríguez Rodríguez, Armando; Vanegas Tenezaca, Evelyn Dayanara; Vento Álvarez, José Raúl; López-Amo Sáinz, Manuel; Bravo Acha, Mikel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Uniertsitate Publikoa
This paper presents a Power-over-Fiber based remote electronic and optical fiber sensors multiplexing scheme. The system architecture consists of a 50-km linear cavity Raman-fiber laser that is used for interrogation of FBG optical fiber sensors. Simultaneously, electronic sensors information is modulated in amplitude while the optical sensors' data are encoded in the spectral information. In order to bias the electronic sensors, the residual power of the Raman pump laser is collected in an energy harvesting unit. This electric power is used for biasing an ATTiny85 control unit and two electro-optical modulators. A proof-of-concept is presented where a couple of optical fiber-Bragg-gratings sensors collect strain information that is self-compensated in temperature according to the digital data achieved from the electronic sensors. A 9.6 kbit/s data rate was achieved using Mach-Zehnder amplitude modulators and a maximum 35 ksample/s was retrieved using a high-speed C-band spectrometer and performing spectral analysis via a software developed in Python. Authors