García Fuentes, Gonzalo
Loading...
Email Address
person.page.identifierURI
Birth Date
Job Title
Last Name
García Fuentes
First Name
Gonzalo
person.page.departamento
Ingeniería
person.page.instituteName
ORCID
person.page.observainves
person.page.upna
Name
- Publications
- item.page.relationships.isAdvisorOfPublication
- item.page.relationships.isAdvisorTFEOfPublication
- item.page.relationships.isAuthorMDOfPublication
2 results
Search Results
Now showing 1 - 2 of 2
Publication Open Access Chemical and mechanical stability of air annealed cathodic arc evaporated CrAlON coatings(Elsevier, 2018) Almandoz Sánchez, Eluxka; García Fuentes, Gonzalo; Martínez de Bujanda Carasusán, Javier; Rodríguez Trías, Rafael; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; IngenieríaThis study reports the synthesis and characterization of ternary Cr-Al-O and quaternary Cr-Al-O-N coatings deposited by cathodic arc physical vapour deposition, for various nitrogen and oxygen mass flow ratios during the growth process. The composition, microstructure, indentation hardness and modulus of the films have been characterized by scanning electron microscopy, electron probe micro-analysis, X-ray diffraction, and nanoindentation techniques. The evolution of the microstructure and mechanical properties of the coatings after ambient air annealing from 800 °C up to 1100 °C have been investigated. As the oxygen to nitrogen mass flow increases, the as-deposited coatings exhibit lower hardness, higher roughness, lower crystallinity and a more marked columnar structure. At oxygen to nitrogen mass flow ratios bigger than 10/90, the coatings exhibit a stoichiometry of the type (CrAl)2+εO3−ε. Only the coatings with an oxygen to nitrogen mass flow ratio smaller than 10/90 retained nitrogen in their compositions. In all cases, the coatings developed a cubic fcc lattice structure. After annealing at 1100 °C the resulting microstructure showed a clear dependency upon the initial composition of the films. The evolution of the microstructure during the high temperature tests, as well as the analysis of the nanoindentation hardness, composition and thickness also provided valuable information about the combined effects of the thermal stability and the oxidation of the deposited coatings.Publication Open Access Corrosion and tribological performance of diamond-like carbon-coated ZK 60 magnesium alloy(MDPI, 2023) Claver Alba, Adrián; Fernández, Iván; Santiago, José A.; Díaz-Rodríguez, Pablo; Panizo-Laiz, Miguel; Esparza Gorráiz, Joseba; García Fuentes, Gonzalo; Zalakain Iriazabal, Iñaki; García Lorente, José Antonio; Institute for Advanced Materials and Mathematics - INAMAT2In this work, hydrogenated and hydrogen-free Diamond-Like Carbon (DLC) coatings were deposited into ZK60 magnesium alloy using the promising coating method High-Power Impulse Magnetron Sputtering (HiPIMS). CrC and WC were used as interlayers of the thin films, and their influence was studied. The structure and composition of the coatings were characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and Raman spectroscopy. Tribological tests, scratch tests, and nanoindentation were performed to obtain information about the mechanical and tribological properties of the coatings. Finally, immersion and electrochemical tests were performed to evaluate the corrosion behavior of the samples. The results showed a homogeneous layer with improved wear resistance, toughness, and hardness in addition to good adhesion to the substrate of the ZK60 magnesium alloy. The hydrogenated DLC coating showed better results that the hydrogen-free thin layer, and relevant differences were observed depending on the interlayer. In this work, the improvement in the tribological and corrosive properties of Mg alloys was studied by using thin layers of DLC and different intermediate layers, achieving similar or even better wear and adhesion values than with thicker layers.