Open Access
Phasorial DPP-BOTDA sensor tolerant to non-local effects
(SPIE, 2014) Urricelqui Polvorinos, Javier; Mariñelarena Ollacarizqueta, Jon; Sagüés García, Mikel; Loayssa Lara, Alayn; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
We introduce a modification of the differential pulse width pair technique in a BOTDA sensor based on a phase modulated probe wave and RF demodulation. This provides a differential Brillouin phasorial signal with high spatial and spectral resolution in both components (magnitude and phase shift). Moreover, the use of a phase modulated probe wave provides RF phase shift measurements tolerant to the emergence of non local effects. The combination of both techniques can lead to the development of long range BOTDA sensors. Proof of concept experiments demonstrate RF phase shift measurements with 1m spatial resolution over 50km and an uncertainty of 1.3ºC at the worst contrast position.
Open Access
Structural health monitoring of solar trackers using distributed fiber optic sensors
(SPIE, 2019) Mariñelarena Ollacarizqueta, Jon; Mompó Roselló, Juan José; Zurita Gabasa, Jesús; Urricelqui Polvorinos, Javier; Júdez Colorado, Aitor; López-Amo Sáinz, Manuel; Jiménez Romero, Sergio; Achaerandio, Álvaro; Loayssa Lara, Alayn; Institute of Smart Cities - ISC; Gobierno de Navarra / Nafarroako Gobernua, 0011-1365-2017-000122; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
We demonstrate the application of a novel type of distributed fiber optic sensors (DFOSs) to dynamically monitor the effects of wind on solar tracker structures used in photovoltaic power stations. This DFOS is based on the stimulated Brillouin scattering nonlinear optical effect in optical fiber, which can be used to measure the distribution of strain and temperature along a given structure. However, contrary to existing solutions, the sensor provides dynamic real-time measurements with hundreds or even thousands of full simultaneous measurements for all positions in the fiber each second. Moreover, high-precision and high spatial resolution are obtained. This so-called dynamic Brillouin optical time-domain analysis (D-BOTDA) sensor provides real-time monitoring of the bending and torsion of the structure of solar trackers in response to wind load. This helps the solar tracker manufacturer asses and improve the mechanical designs so as to introduce corrective measures and develop cost-effective components that properly withstand the effects of wind at any given location. We experimentally demonstrate the application of a D-BOTDA sensing system to measure distributed bending and, for the first time to our knowledge, also distributed torsion along the stressed beam of the solar tracker. For this purpose, we have developed a procedure to instrument the torsion beam with two optical sensing fibers that are fixed helically wound along the beam in opposite directions, so that any common-mode thermal or bending effects are removed. We initially performed tests in a laboratory facility in which sections of the torsion beam could be subjected to controlled moments. Static and dynamic loads were applied and the measured deformations were compared to those obtained with fiber Bragg gratings, which just provide point measurements of strain. In both cases, full agreement was demonstrated. Finally, the system was installed in an operational solar park.
Open Access
Gain dependence of measured spectra in coherent Brillouin optical time-domain analysis sensors
(SPIE, 2016) Mariñelarena Ollacarizqueta, Jon; Urricelqui Polvorinos, Javier; Loayssa Lara, Alayn; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
We report on the effects of large pump pulse powers on Brillouin optical time-domain analysis (BOTDA) sensors based on phase-modulated probe wave and coherent detection. It is found that the large Brillouin gain that comes from the use of high power pulses induces a narrowing of the RF phase-shift spectrum that is measured in these sensors. This narrowing leads to a Brillouin frequency shift measurement error when the sensor is configured for dynamic measurements. However, the effect has been found to be less significant than that observed in dynamic slope-assisted BOTDA sensors based on amplitude.
Open Access
Simplified Brillouin sensor for structural health monitoring applications based on passive optical filtering
(SPIE, 2015) Iribas Pardo, Haritz; Urricelqui Polvorinos, Javier; Mariñelarena Ollacarizqueta, Jon; Sagüés García, Mikel; Loayssa Lara, Alayn; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
We present a simplified configuration for distributed Brillouin optical time domain analysis sensors. The technique is based on passive optical filtering of the spectral components generated in an RF-pulse-modulated optical source. The aim of this configuration is to reduce the cost of the sensor by simplifying the generation of the optical waves involved in the sensing process. Proof-of-concept experiments demonstrate distributed temperature measurement with 1 m resolution over a 20 km sensing fiber.
Open Access
Latest research on long-range Brillouin distributed sensing
(SPIE, 2019) Loayssa Lara, Alayn; Urricelqui Polvorinos, Javier; Iribas Pardo, Haritz; Mariñelarena Ollacarizqueta, Jon; Mompó Roselló, Juan José; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa; Gobierno de Navarra / Nafarroako Gobernua projecto 0011-1365-2017-000122
We review the latest developments in long-range Brillouin optical time-domain analysis sensors. The factors that impair the performance of these sensors, particularly in terms of their distance range, are discussed together with the latest methods to overcome them. We focus on our recent contributions based on the application of the probe dithering method, which is based on introducing a wavelength modulation to the probe wave. This technique is shown to effectively compensate nonlocal effects originated in the depletion of the pump pulse as well as of its pedestal. In addition, it can provide amplification to the pump wave with a slight modification of the setup. Furthermore, this method can be combined with pump pulse coding and a new technique for coding linearization that we have devised to further extend the sensing length into the hundreds of kilometers range.