Open Access
Optical-microwave sensor for real-time measurement of water contamination in oil derivatives
(Elsevier, 2023) Abdulsattar, Rusul K.; Alibakhshikenari, Mohammad; Virdee, Bal S.; Sharma, Richa; Elwi, Taha A.; Kouhalvandi, Lida; Hassain, Zaid Abdul; Ali, Syed Mansoor; Türker Tokan, Nurhan; Livreri, Patrizia; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents a novel microwave sensor using optical activation for measuring in real-time the water contamination in crude oil or its derivatives. The sensor is constructed from an end-coupled microstrip resonator that is interconnected to two pairs of identical fractal structures based on Moore curves. Electromagnetic (EM) interaction between the fractal curves is mitigated using a T-shaped microstrip-stub to enhance the performance of the sensor. The gap in one pair of fractal curves is loaded with light dependent resistors (LDR) and the other pair with microwave chip capacitors. The chip capacitors were used to increase the EM coupling between the fractal gaps to realize a high Q-factor resonator that determines the sensitivity of the sensor. Empirical results presented here show that the insertion-loss of the sensor is affected by the change in LDR impedance when illuminated by light. This property is used to determine the amount of water contaminated oil. The sensitivity of the sensor was optimized using commercial 3D EM solver. The measurements were made by placing a 30 mm diameter petri dish holding the sample on top of the sensor. The petri dish was filled up to a height of 10 mm with the sample of water contaminated crude oil, and the measurements were done in the range between 0.76 GHz and 1.2 GHz. The Q-factor of the oil sample with no water contamination was 70 and the Q-factor declined to 20 for 100% contamination. The error in the measurements was less than 0.024%. The sensor has dimensions of 0.127λo × 0.127λo × 0.004 λo and represents a new modality. Compared to existing techniques, the proposed sensor is simple to use, readily portable and is more sensitive.
Open Access
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
(Elsevier, 2023) Muqdad, Zainab S.; Alibakhshikenari, Mohammad; Elwi, Taha A.; Hassain, Zaid Abdul; Virdee, Bal S.; Sharma, Richa; Khan, Salahuddin; Türker Tokan, Nurhan; Livreri, Patrizia; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. The antenna is shown to exhibit a large impedance bandwidth and is capable of radiating energy in a specified direction. The proposed antenna consists of a standard rectangular patch on which is embedded an H-tree shaped fractal slot of order 3. The fractal slot is used to effectively reduce the physical size of the patch by 75 % and to enhance its impedance bandwidth. A metasurface layer is strategically placed above the patch radiator with a narrow air gap between the two. The metasurface layer is a lattice pattern of square framed rhombus ring shaped unit-cells that are interconnected by PIN photodiodes. The metasurface layer essentially acts like a superstrate when exposed to RF/microwave radiation. Placed below the patch antenna is a conductive layer that acts like a reflector to enhance the front-toback ratio by blocking radiation from the backside of the patch radiator. The patch’s main beam can be precisely controlled by photonically illuminating the metasurface layer. The antenna’s performance was modelled and analyzed with a commercial 3D electromagnetic solver. The antenna was fabricated on a standard dielectric substrate FR4 and has dimensions of 0.778λo × 0.778λo × 0.25λo mm3 , where λo is the wavelength of free space centered at 1.35 GHz. Measured results confirm the antenna’s performance. The antenna exhibits a wide fractional band of 55.5 % from 0.978 to 1.73 GHz for reflection-coefficient (S11) better than − 10 dB. It has a maximum gain of 9 dBi at 1.35 GHz with a maximum front-to-back ratio (F/B) of 21 dBi. The main beam can be steered in the elevation plane from − 24◦ to +24◦. The advantage of the proposed antenna is it does not require any mechanical movements or complicated electronic systems.

Falcone Lanas, Francisco

Email Address

person.page.identifierURI

Birth Date

Job Title

Last Name

First Name

person.page.departamento

person.page.instituteName

ORCID

person.page.observainves

person.page.upna

Name

Filters

Author

Subject

Date

Has files

Item Type

Type

Settings

Sort By

Results per page

Search Results