Open Access
Multimode HMSIW-based bandpass filter with improved selectivity for fifth-generation (5G) RF front-ends
(MDPI, 2020) Iqbal, Amjad; Tiang, Jun Jiat; Wong, Sew Kin; Alibakhshikenari, Mohammad; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This article presents the detailed theoretical, simulation, and experimental analysis of a half-mode substrate integrated waveguide (HMSIW)-based multimode wideband filter. A third-order, semicircular HMSIW filter is developed in this paper. A semicircular HMSIW cavity resonator is adopted to achieve wide band characteristics. A U-shaped slot (acts as a lambda/4 stub) in the center of a semicircular HMSIW cavity resonator and L-shaped open-circuited stubs are used to improve the out-of-band response by generating multiple transmission zeros (TZs) in the stop-band region of the filter. The TZs on either side of the passband can be controlled by adjusting dimensions of a U-shaped slot and L-shaped open-circuited stubs. The proposed filter covers a wide fractional bandwidth, has a lower insertion loss value, and has multiple TZs (which improves the selectivity). The simulated response of filter agrees well with the measured data. The proposed HMSIW bandpass filter can be integrated with any planar wideband communication system circuit, thanks to its planar structure.
Open Access
Miniaturization trends in substrate integrated waveguide (SIW) filters: a review
(IEEE, 2020) Iqbal, Amjad; Tiang, Jun Jiat; Wong, Sew Kin; Alibakhshikenari, Mohammad; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This review provides an overview of the technological advancements and miniaturization trends in Substrate Integrated Waveguide (SIW) filters. SIW is an emerging planar waveguide structure for the transmission of electromagnetic (EM) waves. SIW structure consists of two parallel copper plates which are connected by a series of vias or continuous perfect electric conductor (PEC) channels. SIW is a suitable choice for designing and developing the microwave and millimetre-wave (mm-Wave) radio frequency (RF) components: because it has compact dimensions, low insertion loss, high-quality factor (QF), and can easily integrate with planar RF components. SIW technology enjoys the advantages of the classical bulky waveguides in a planar structure; thus is a promising choice for microwave and mm-Wave RF components. © 2013 IEEE.
Open Access
Isolation improvement in UWB-MIMO antenna system using slotted stub
(MDPI, 2020) Altaf, Ahsan; Iqbal, Amjad; Smida, Amor; Smida, Jamel; Falcone Lanas, Francisco; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Multiple-input multiple-output (MIMO) scheme refers to the technology where more than one antenna is used for transmitting and receiving the information packets. It enhances the channel capacity without more power. The available space in the modern compact devices is limited and MIMO antenna elements need to be placed closely. The closely spaced antennas undergo an undesirable coupling, which deteriorates the antenna parameters. In this paper, an ultra wide-band (UWB) MIMO antenna system with an improved isolation is presented. The system has a wide bandwidth range from 2–13.7 GHz. The antenna elements are closely placed with an edge to edge distance of 3 mm. In addition to the UWB attribute of the system, the mutual coupling between the antennas is reduced by using slotted stub. The isolation is improved and is below −20 dB within the whole operating range. By introducing the decoupling network, the key performance parameters of the antenna are not affected. The system is designed on an inexpensive and easily available FR-4 substrate. To better understand the working of the proposed system, the equivalent circuit model is also presented. To model the proposed system accurately, different radiating modes and inter-mode coupling is considered and modeled. The EM model, circuit model, and the measured results are in good agreement. Different key performance parameters of the system and the antenna element such as envelope correlation coefficient (ECC), diversity gain, channel capcity loss (CCL) gain, radiation patterns, surface currents, and scattering parameters are presented. State-of-the-art comparison with the recent literature shows that the proposed antenna has minimal dimensions, a large bandwidth, an adequate gain value and a high isolation. It is worth noticeable that the proposed antenna has high isolation even the patches has low edge-to-edge gap (3 mm). Based on its good performance and compact dimensions, the proposed antenna is a suitable choice for high throughput compact UWB transceivers.
Open Access
High performance antenna-on-chip inspired by SIW and metasurface technologies for THz band operation
(Springer, 2023) Alibakhshikenari, Mohammad; Virdee, Bal S.; Rajaguru, Renu Karthick; Iqbal, Amjad; Al-Hasan, Muath; See, Chan H.; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a high-performance antenna-on-chip (AoC) is implemented on gallium arsenide (GaAs) wafer based on the substrate integrated waveguide (SIW) and metasurface (MTS) technologies for terahertz band applications. The proposed antenna is constructed using fve stacked layers comprising metal-GaAs-metal-GaAs-metal. The conductive electromagnetic radiators are implemented on the upper side of the top GaAs layer, which has a metallic ground-plane at its underside. The metallic feedline is implemented at the underside of the bottom GaAs layer. Dual wrench-shaped radiators are framed by metallic vias connected to the ground-plane to create SIW cavity. This technique mitigates the surface waves and the substrate losses, thereby improving the antenna’s radiation characteristics. The antenna is excited by a T-shaped feedline implemented on the underside of the bottom GaAs substrate layer. Electromagnetic (EM) energy from the feedline is coupled to the radiating elements through the circular and linear slots etched in the middle ground-plane layer. To mitigate the surfacewave interactions and the substrate losses in the bottom GaAs layer, the feedline is contained inside a SIW cavity. To enhance the antenna’s performance, the radiators are transformed into a metamaterialinspired surface (i.e., metasurface), by engraving periodic arrangement of circular slots of subwavelength diameter and periodicity. Essentially, the slots act as resonant scatterers, which control the EM response of the surface. The antenna of dimensions of 400× 400 × 8 μm3 is demonstrated to operate over a wide frequency range from 0.445 to 0.470THz having a bandwidth of 25GHz with an average return-loss of− 27 dB. The measured average gain and radiation efciency are 4.6 dBi and 74%, respectively. These results make the proposed antenna suitable for AoC terahertz applications.
Open Access
Metamaterial inspired electromagnetic bandgap filter for ultra-wide stopband screening devices of electromagnetic interference
(Springer, 2023) Al-Hasan, Muath; Alibakhshikenari, Mohammad; Virdee, Bal S.; Sharma, Richa; Iqbal, Amjad; Althuwayb, Ayman Abdulhadi; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Presented here is a reactively loaded microstrip transmission line that exhibit an ultra-wide bandgap. The reactive loading is periodically distributed along the transmission line, which is electromagnetically coupled. The reactive load consists of a circular shaped patch which is converted to a metamaterial structure by embedded on it two concentric slit-rings. The patch is connected to the ground plane with a via-hole. The resulting structure exhibits electromagnetic bandgap (EBG) properties. The size and gap between the slit-rings dictate the magnitude of the reactive loading. The structure was frst theoretically modelled to gain insight of the characterizing parameters. The equivalent circuit was verifed using a full-wave 3D electromagnetic (EM) solver. The measured results show the proposed EBG structure has a highly sharp 3-dB skirt and a very wide bandgap, which is substantially larger than any EBG structure reported to date. The bandgap rejection of the single EBG unit-cell is better than − 30 dB, and the fve element EBG unit-cell is better than − 90 dB. The innovation can be used in various applications such as biomedical applications that are requiring sharp roll-of rates and high stopband rejection thus enabling efcient use of the EM spectrum. This can reduce guard band and thereby increase the channel capacity of wireless systems.