Open Access
Inertia transfer concept based general method for the determination of the base inertial parameters
(Springer, 2015) Ros Ganuza, Javier; Plaza Puértolas, Aitor; Iriarte Goñi, Xabier; Aginaga García, Jokin; Ingeniería; Ingeniaritza; Institute of Smart Cities - ISC
This paper presents a new algorithm to obtain the symbolic expressions of any of the possible base inertial parameter sets of a multibody system. Based on the ¿inertia transfer concept¿, a procedure is proposed to write a system of equations from which the base parameters are obtained. This leads to an automatizable and general method to obtain these parameters symbolically. The method can also be used to determine base inertial parameters numerically, and it can be even more straightforward to implement and use than the standard numerical methods. An example is presented to illustrate in detail the application of the algorithm, and to compare its results with those of a standard numerical procedure. The symbolic base inertial parameters can be of interest in symbolic simplification of the dynamic equations for real-time applications, design optimization, dynamic parameter identification, model reduction, and in other fields.
Open Access
Determination of the symbolic base inertial parameters of planar mechanisms
(Elsevier, 2017) Iriarte Goñi, Xabier; Ros Ganuza, Javier; Mata, Vicente; Aginaga García, Jokin; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
The inertial information of a planar mechanical system is characterised using 4 inertial parameters per solid. Due to the kinematic constraints, this parametrisation turns out be redundant. In order to reduce the computational cost of the model and make it possible to estimate its inertial parameters, the model is usually written in terms of a minimum set of inertial parameters called base inertial parameters. These parameters completely determine the dynamics of motion (kinetics) of a mechanism and, since their contributions are independent to each other, their actual values can be estimated experimentally. The base inertial parameters expressions can be written as a linear combination of the inertial parameters and determining their symbolic expressions provides a deeper insight into their physical meaning. This paper presents a new algorithm to determine the symbolic expressions of the base inertial parameters of planar mechanisms. The approach is based on a very well known numerical method to obtain the base inertial parameters and on the fact that these parameters belong to a class of functions that lets us search for symbolic expressions matching with them. Since the symbolic expressions are a function of the geometric constants of the system, the presented algorithm constitutes a very valuable tool in design optimisation and it is also very interesting in dynamic parameter estimation, model reduction and other fields.
Open Access
Optimal strain-gauge placement for mechanical load estimation in circular cross-section shafts
(Elsevier, 2021) Iriarte Goñi, Xabier; Aginaga García, Jokin; Gainza González, Gorka; Ros Ganuza, Javier; Bacaicoa Díaz, Julen; Institute of Smart Cities - ISC
The customary electrical circuit configuration for estimating mechanical loads with strain gauges uses Wheatstone full- or half-bridges. For each mechanical load to be estimated, a dedicated bridge with two or four gauges has to be mounted, placing the strain gauges in specific configurations along the measured part. In this paper the strain of individual gauges is measured by means of quarter-bridges and all the mechanical loads exerted on a shaft are estimated jointly as different linear combinations of the strains of the gauges. The location of the gauges on the shaft are determined optimally and the influence of apparent strain related to temperature variations is avoided. Results show several configurations of reduced sets of gauges capable of optimally estimating the six components of the mechanical loads exerted on a circular cross-section shaft. The validation of the approach in a dedicated rig has shown the complexity of its experimental implementation.
Open Access
Optimal strain gauge configurations for the estimation of mechanical loads in the main shaft of HAWT
(IOP Publishing, 2020) Iriarte Goñi, Xabier; Aginaga García, Jokin; Lerga Valencia, Francisco Javier; Gainza González, Gorka; Ros Ganuza, Javier; Bacaicoa Díaz, Julen; Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería
In Structural Health Monitoring of wind turbines, measuring the mechanical loads is a key issue. The customary techniques for this task use a full-bridge strain gauge configuration to measure each of the six load components exerted on the shaft. However, using only six strain gauges should be sufficient to estimate the six load components if a one-to-one correspondence was achieved. In this paper a different approach to mechanical loads estimation is presented where, measuring the strain of individual gauges in quarter-bridge configurations, it is possible to estimate all the load components from a single set of gauges. The configurations are optimally determined making use of the D-optimality criterion, which maximises the observability of the estimated components. The approach also provides configurations where the apparent strain related to temperature variations is automatically compensated. Results show several optimal configurations for different measuring conditions and shows that six strain gauges are enough to estimate all the load components. The new approach also opens the possibility to obtain configurations with more strain gauges as well as configurations that have to meet other requirements.

Aginaga García, Jokin

Email Address

person.page.identifierURI

Birth Date

Job Title

Last Name

First Name

person.page.departamento

person.page.instituteName

ORCID

person.page.observainves

person.page.upna

Name

Filters

Author

Subject

Date

Has files

Item Type

Type

Settings

Sort By

Results per page

Search Results