Person:
Teniente Vallinas, Jorge

Loading...
Profile Picture

Email Address

Birth Date

Job Title

Last Name

Teniente Vallinas

First Name

Jorge

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

person.page.instituteName

ISC. Institute of Smart Cities

person.page.observainves

person.page.upna

Name

Search Results

Now showing 1 - 10 of 14
  • PublicationOpen Access
    Advanced feeds for mm-wave antenna systems
    (Springer, 2018) Teniente Vallinas, Jorge; Iriarte Galarregui, Juan Carlos; Ederra Urzainqui, Íñigo; Gonzalo García, Ramón; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    Millimeter-wave antenna systems have traditionally required high performance feeds in order to fulfill its stringent requirements. Therefore, this goal has been achieved by corrugated horns. However, in the last years new applications mainly in the communication systems have driven the use of other types of antenna feed with slightly reduced performance but simpler manufacturing at mm-wave and submm-wave frequencies with improvements in cost reduction. These advanced profiles are usually based in smooth waveguide advanced profiles. Besides, the chapter describes different feed configurations based on metamaterial structures and several examples of metamaterial based or inspired antennas are considered. Then, this chapter covers the different alternatives currently used for mm-wave antenna feed: corrugated horns, spline horns, and metamaterial horns. At the end of each section, it includes some research successful results.
  • PublicationOpen Access
    All-metallic ε-near-zero (ENZ) lens based on ultra-narrow hollow rectangular waveguides: experimental results
    (IEEE, 2014) Orazbayev, Bakhtiyar; Torres Landívar, Víctor; Pacheco-Peña, Víctor; Falcone Lanas, Francisco; Teniente Vallinas, Jorge; Beruete Díaz, Miguel; Sorolla Ayza, Mario; Navarro Cía, Miguel; Engheta, Nader; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    Here we perform numerical and experimental investigation of plano-concave all-metallic ε-near-zero (ENZ) lens with operational frequency f = 144 GHz. The ENZ lens is achieved by stacking an array of narrow hollow rectangular waveguides working near cut-off frequency. Focusing and radiation properties are numerically analyzed and measured. The enhancement of 5.61 dB and directivity of 17.6 dBi are shown. Good agreement between experimental and numerical results is demonstrated.
  • PublicationOpen Access
    Suberb gaussian beam efficiency corrugated horn antennas
    (2010) Teniente Vallinas, Jorge; Gonzalo García, Ramón; Río Bocio, Carlos del; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
    In this paper we are presenting the possibilities of corrugated horn antennas that combine horizontal and vertical corrugations.
  • PublicationOpen Access
    Instalaciones para la medida de antenas en la UPNA
    (2018) Teniente Vallinas, Jorge; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
  • PublicationEmbargo
    Experimental validation of a Ku-band dual circularly polarized metasurface antenna
    (IEEE, 2018) Tellechea Pereda, Amagoia; Caminita, Francesco; Martini, Enrica; Ederra Urzainqui, Íñigo; Teniente Vallinas, Jorge; Iriarte Galarregui, Juan Carlos; Gonzalo García, Ramón; Maci, Stefano; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
    The experimental validation of a Ku-band dual circularly polarized (CP) broadside-beam metasurface (MTS) antenna is presented. A radially modulated anisotropic single layer MTS has been synthesised employing sub-wavelength elliptical slotted metallic patches printed on top of a thin Arlon grounded substrate. In the structure, two decoupled phasematched transverse magnetic and transverse electric surface waves (SWs) are excited, which interact with the modulated surface leading to a CP broadside radiation. Two different orthomode transducers have been designed to excite the SWs with orthogonal polarization and equal amplitude. The first feeding system is composed of a metallic stepped septum inside an airfilled square waveguide. A conical section is included to match the output port of the square waveguide with the terminal, dielectric filled circular waveguide. The second feed is much more compact and efficient and it is composed of a circular waveguide completely filled by a dielectric. Depending on the input port excited on the feeds, two TE11 modes are excited with ±90° phase shift, which determine the right-hand or left-hand sense of the broadside beam generated by the MTS. Manufacturing details of the MTS and excitations are given and the measurements are compared with the simulation results. Finally, conclusions are drawn.
  • PublicationOpen Access
    Corrugated horn antenna noise temperature characterisation for the NRL water vapor millimeter-wave spectrometer project
    (2011) Teniente Vallinas, Jorge; Gómez, R.M.; Maestrojuán Biurrun, Itziar; Rebollo Mugueta, Ainara; Gonzalo García, Ramón; Río Bocio, Carlos del; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
    In this paper the antenna noise temperature for two different corrugated horn antennas (old model and new model) for NRL WVMS is being characterized. The whole optical system will be simulated with Ticra’s GRASP software, and the corrugated horns with Mician μWave Wizard software. Spherical wave expansion from Mician μWave Wizard will be exported to Ticra’s GRASP to connect both results.
  • PublicationOpen Access
    Soret fishnet metalens antenna
    (Springer Nature, 2015) Orazbayev, Bakhtiyar; Beruete Díaz, Miguel; Pacheco-Peña, Víctor; Crespo López, Gonzalo; Teniente Vallinas, Jorge; Navarro Cía, Miguel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
    At the expense of frequency narrowing, binary amplitude-only diffractive optical elements emulate refractive lenses without the need of large profiles. Unfortunately, they also present larger Fresnel reflection loss than conventional lenses. This is usually tackled by implementing unattractive cumbersome designs. Here we demonstrate that simplicity is not at odds with performance and we show how the fishnet metamaterial can improve the radiation pattern of a Soret lens. The building block of this advanced Soret lens is the fishnet metamaterial operating in the near-zero refractive index regime with one of the edge layers designed with alternating opaque and transparent concentric rings made of subwavelength holes. The hybrid Soret fishnet metalens retains all themeritsof classicalSoret lenses suchas lowprofile, lowcost andeaseofmanufacturing. It is designed for the W-band of themillimeter-waves range with a subwavelength focal lengthFL51.58 mm(0.5l0) aiming at a compact antenna or radar systems. The focal properties of the lens along with its radiation characteristics in a lens antenna configuration have been studied numerically and confirmed experimentally, showing a gain improvement of ,2 dB with respect to a fishnet Soret lens without the fishnet metamaterial.
  • PublicationOpen Access
    3-D printed horn antennas and components performance for space and telecommunications
    (IEEE, 2018) Teniente Vallinas, Jorge; Iriarte Galarregui, Juan Carlos; Caballero Nagore, Rubén; Valcázar Berdofe, Daniel; Goñi, Mikel; Martínez, Aitor; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    In this work, a study of the performance of several antennas and components, manufactured using an accurate stereolithography 3D printer and resin for maximum accuracy and detail, is carried out. Electroless plating of the components to cover the pieces with a thick copper layer to improve their mechanical resistance is undertaken. Several SatCom horn antennas and components are designed, manufactured, and tested. A detailed study of a spline horn antenna and a filter is covered. These results are compared to the metallic lathe manufactured versions. Conclusions are derived from these tests, which are useful to improve additive manufactured components in future versions.
  • PublicationOpen Access
    Experimental study of the antenna influence in RTLS based-on RFID
    (IEEE, 2012) Crespo López, Gonzalo; Teniente Vallinas, Jorge; Ederra Urzainqui, Íñigo; Gonzalo García, Ramón; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
    Nowadays Real-time localization systems (RTLS) are growing up very quickly but there are some remaining issues which need to be analyzed. This paper presents an experimental study that shows how different kind of antennas can help to reach a more accurate localization. Among all different wireless technologies, active radio-frequency identification (RFID) has been chosen due to its development and simplicity. The study has been divided into two different parts. Firstly RF tests are made to assure received signal strength indicator (RSSI) levels are the expected. Secondly measurements with different antennas have been performed. The antennas used in this study are: an Omni-directional monopole standard antenna, a Patch antenna and a 2 Patch Array antenna both in a FR4 substrate.
  • PublicationOpen Access
    Real-time imaging with frequency scanning array antenna for industrial inspection applications at W band
    (Springer, 2018) Larumbe Gonzalo, Belén; Laviada, Jaime; Ibáñez Loinaz, Asier; Teniente Vallinas, Jorge; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
    A real-time imaging system based on a frequency scanning antenna for conveyor belt setups is presented in this paper. The frequency scanning antenna together with an inexpensive parabolic reflector operates at the W band enabling the detection of details with dimensions in the order of 2 mm. In addition, a low level of sidelobes is achieved by optimizing unequal dividers to window the power distribution for sidelobe reduction. Furthermore, the quality of the images is enhanced by the radiation pattern properties. The performance of the system is validated by showing simulation as well as experimental results obtained in real time, proving the feasibility of these kinds of frequency scanning antennas for cost-effective imaging applications.