Atienza Martínez, María

Profile Picture

Email Address

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/48629

Birth Date

Job Title

Last Name

Atienza Martínez

First Name

María

person.page.departamento

Ciencias

person.page.instituteName

ORCID

0000-0002-5047-5106

person.page.observainves

750701

person.page.upna

811943

Name

Filters

20243
Reset filters

Settings

Author: Bimbela Serrano, Fernando × End date: 2025 ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    PublicationOpen Access
    Innovative flow-through reaction system for the sustainable production of phenolic monomers from lignocellulose catalyzed by supported Mo2C
    (Wiley, 2024) Maisterra Udi, Maitane; Atienza Martínez, María; Hablich Alvarracin, Karina Lissett; Moreira, Rui; Martínez Merino, Víctor; Gandía Pascual, Luis; Cornejo Ibergallartu, Alfonso; Bimbela Serrano, Fernando; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra - Nafarroako Unibertsitate Publikoa
    Molybdenum carbide supported on activated carbon (β-Mo2C/AC) has been tested as catalyst in the reductive catalytic fractionation (RCF) of lignocellulosic biomass both in batch and in Flow-Through (FT) reaction systems. High phenolic monomer yields (34 wt.%) and selectivity to monomers with reduced side alkyl chains (up to 80 wt.%) could be achieved in batch in the presence of hydrogen. FT-RCF were made with no hydrogen feed, thus via transfer hydrogenation from ethanol. Similar selectivity could be attained in FT-RCF using high catalyst/biomass ratios (0.6) and high molybdenum loading (35 wt.%) in the catalyst, although selectivity decreased with lower catalyst/biomass ratios or molybdenum contents. Regardless of these parameters, high delignification of the lignocellulosic biomass and similar monomer yields were observed in the FT mode (13-15 wt.%) while preserving the holocellulose fractions in the delignified pulp. FT-RCF system outperforms the batch reaction mode in the absence of hydrogen, both in terms of activity and selectivity to reduced monomers that is attributed to the two-step non-equilibrium processes and the removal of diffusional limitations that occur in the FT mode. Even though some molybdenum leaching was detected, the catalytic performance could be maintained with negligible loss of activity or selectivity for 15 consecutive runs.
  • Thumbnail Image
    PublicationOpen Access
    Remarkable performance of supported Rh catalysts in the dry and combined reforming of biogas at high space velocities
    (Elsevier, 2024) Navarro Puyuelo, Andrea; Atienza Martínez, María; Reyero Zaragoza, Inés; Bimbela Serrano, Fernando; Gandía Pascual, Luis; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    Dry and combined (with O2) reforming of synthetic biogas were studied at 700 °C using 0.5 % Rh catalysts prepared by impregnation on different supports: γ-Al2O3, SiO2, TiO2, ZrO2 and CeO2. Gas hourly space velocity (GHSV) was varied between 150 and 700 N L CH4/(gcat·h), and two O2/CH4 molar ratios of 0 and 0.12 were studied. Rh/Al2O3 catalysts (prepared using two different commercial supports here denoted as Sph and AA) presented the highest biogas conversion and syngas yields under both dry and combined reforming conditions. Catalytic activities were as follows: Rh/AA ≈ Rh/Sph > Rh/SiO2 > Rh/ZrO2 ≈ Rh/CeO2 > Rh/TiO2. The effect of catalysts’ calcination pre-treatment at relatively low (200 °C) and high temperatures (750 °C) was also studied. Calcination at high temperatures had a detrimental effect on both dry and combined reforming activities. However, a positive effect on the reforming activities and syngas yields was observed when the catalysts were calcined at 200 °C, especially under biogas combined reforming conditions: higher CH4 conversions and syngas yields could be achieved, as well as increasing CO2 conversions, though at the expense of lower H2/CO molar ratios.
  • Thumbnail Image
    PublicationOpen Access
    Comparative study of supported Ni and Co catalysts prepared using the All-in-One method in the hydrogenation of CO2: effects of using (Poly)Vinyl Alcohol (PVA) as an additive
    (MDPI, 2024) Navarrete Rodríguez, Luisa Fernanda; Atienza Martínez, María; Reyero Zaragoza, Inés; Urroz Unzueta, José Carlos; Amorrortu, Oihana; Sanz Iturralde, Oihane; Montes, Mario; Garcés, Siby I.; Bimbela Serrano, Fernando; Gandía Pascual, Luis; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería; Ingeniaritza
    Two series of Ni and Co catalysts supported onto La-Al2O3 were prepared and the CO2 hydrogenation reactions investigated. The catalytic performance was evaluated in terms of the evolution with the reaction temperature of the CO2 conversion and product (CH4 and CO) yields, as well as specific activities (TOF) and apparent activation energies. CH4 was the favored product over both metals while the TOF for CH4 formation was about three times higher for Ni than Co at 240–265 °C. Metallic particle size effects were found, with the TOF for CH4 formation decreasing over both Ni and Co as the mean metallic size decreased. In contrast, the TOF for CO formation tended to increase at a decreasing particle size for the catalysts with the smallest Ni particle sizes. The apparent activation energies for Ni and Co were very similar and significantly decreased to values of 73–79 kJ/mol when the metallic dispersion increased. The catalysts were prepared using the all-in-one method, resulting in (poly)vinyl alcohol (PVA) being a key additive that allowed us to enhance the dispersion of Ni and Co to give very effective catalysts. This comparative study joins the few existing ones in the literature in which catalysts based on these metals operated under strictly the same reaction conditions.