Person:
Gubía Villabona, Eugenio

Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Gubía Villabona

First Name

Eugenio

person.page.departamento

ORCID

0000-0002-0067-1715

person.page.upna

1768

Name

Filters

2005 - 20093
Reset filters

Settings

End date: 2009 × Start date: 2005 ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    PublicationOpen Access
    Influence of the power supply on the energy efficiency of an alkaline water electrolyser
    (Elsevier, 2009) Ursúa Rubio, Alfredo; Marroyo Palomo, Luis; Gubía Villabona, Eugenio; Gandía Pascual, Luis; Diéguez Elizondo, Pedro; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza; Química Aplicada; Kimika Aplikatua; Gobierno de Navarra / Nafarroako Gobernua
    Electric energy consumption represents the greatest part of the cost of the hydrogen produced by water electrolysis. An effort is being carried out to reduce this electric consumption and improve the global efficiency of commercial electrolysers. Whereas relevant progresses are being achieved in cell stack configurations and electrodes performance, there are practically no studies on the effect of the electric power supply topology on the electrolyser energy efficiency. This paper presents an analysis on the energy consumption and efficiency of a 1 N m3 h1 commercial alkaline water electrolyser and their dependence on the power supply topology. The different topologies of power supplies are first summarised, analysed and classified into two groups: thyristor-based (ThPS) and transistor-based power supplies (TrPS). An Electrolyser Power Supply Emulator (EPSE) is then designed, developed and satisfactorily validated by means of simulation and experimental tests. With the EPSE, the electrolyser is characterised both obtaining its I–V curves for different temperatures and measuring the useful hydrogen production. The electrolyser is then supplied by means of two different emulated electric profiles that are characteristic of typical ThPS and TrPS. Results show that the cell stack energy consumption is up to 495 W h N m3 lower when it is supplied by the TrPS, which means 10% greater in terms of efficiency.
  • Thumbnail Image
    PublicationOpen Access
    On the testing, characterization, and evaluation of PV inverters and dynamic MPPT performance under real varying operating conditions
    (Wiley, 2007) Sanchis Gúrpide, Pablo; López Taberna, Jesús; Ursúa Rubio, Alfredo; Gubía Villabona, Eugenio; Marroyo Palomo, Luis; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
    The increasing number of photovoltaic inverters that are coming on to the PV marketstresses the need to carry out a dynamic characterization of these elements and theirmaximum power point tracking (MPPT) algorithms under real operating conditions.In order to make these conditions repeatable at the laboratory, PV array simulatorsare used. However, actual simulators, including the commercial simulators, recreateonly a single or small set of PV array characteristic curves in which quite commonlytheoretical calculations are included in order to simulate irradiance and temperatureartificial variations. This is far from being a recreation of the real and long dynamicbehavior of a PVarray or generator. The testing and evaluation of the performance ofPV inverters and MPPT algorithms has to be carried out when the PV system movesdynamically according to real operating conditions, including processes such asrapidly changing atmospheric conditions, partial shadows, dawn, and nightfall. Thispaper tries to contribute to the analysis of this problem by means of an electronicsystem that both measures the real evolution of the characteristic curves of PVarraysat outdoor operation and then recreates them at the laboratory to test PV inverters.This way the equipment can highlight the different performances of PV inverters andMPPT techniques when they operate under real operating conditions. As an example,two commercial inverters are tested and analyzed under the recreated behavior of aPV generator during 2 singular days that include processes of partial shading and fastirradiance variations.
  • Thumbnail Image
    PublicationOpen Access
    Boost DC-AC inverter: a new control strategy
    (IEEE, 2005) Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Gubía Villabona, Eugenio; Marroyo Palomo, Luis; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    Boost dc–ac inverter naturally generates in a single stage an ac voltage whose peak value can be lower or greater than the dc input voltage. The main drawback of this structure deals with its control. Boost inverter consists of Boost dc–dc converters that have to be controlled in a variable-operation point condition. The sliding mode control has been proposed as an option. However, it does not directly control the inductance averaged-current. This paper proposes a control strategy for the Boost inverter in which each Boost is controlled by means of a double-loop regulation scheme that consists of a new inductor current control inner loop and an also new output voltage control outer loop. These loops include compensations in order to cope with the Boost variable operation point condition and to achieve a high robustness to both input voltage and output current disturbances. As shown by simulation and prototype experimental results, the proposed control strategy achieves a very high reliable performance, even in difficult transient situations such as nonlinear loads, abrupt load changes, short circuits, etc., which sliding mode control cannot cope with.