Open Access
Experimental investigation of a R290 domestic heat pump equipped with a thermoelectric-aided sub-cooler
(Elservier, 2025-06-01) Pendzialek, M.; Özyildiz, Tufan; Fingas, Rafal; Sánchez, Daniel; Aranguren Garacochea, Patricia; Smolka, Jacek; Haida, Michal; Ingeniería; Ingeniaritza; Institute of Smart Cities - ISC
The energy efficiency of heat pumps is an important factor for the sustainability and electrification of domestic heating, especially for the most common air-to-water heat pumps, which are a competitive solution to conventional heating methods. However, novel solutions for cold and moderate climate zones must be developed considering environmentally friendly natural refrigerants such as hydrocarbons. One idea is to introduce a thermoelectric-aided sub-cooler into an air-to-water heat pump to improve the coefficient of performance. Therefore, this work aims to experimentally investigate a novel propane heat pump system with a prototype thermoelectric-aided sub-cooler for domestic heating. Energy analysis was performed to evaluate the energy impact of the sub-cooler in terms of ambient conditions from -10.0 ºC to 5.0 ºC, different water temperatures for heating applications in existing buildings from 45.0 ºC to 55.0 ºC and varying operating conditions of thermoelectric modules in the sub-cooler. The performance of the sub-cooler was evaluated. The results confirm that introducing a thermoelectric-aided sub-cooler can improve the heat pump performance by up to 6.0% and the heating capacity improvement by up to 17.0% for the low ambient temperature of -10.0 ºC. Furthermore, an optimal direct current voltage below 3.0 V was found for every investigated operating condition to ensure the best system coefficient of performance.
Open Access
Advanced phase-change intermediate heat exchanger development for multistage thermoelectric heat pumps
(Elsevier, 2023) Erro Iturralde, Irantzu; Aranguren Garacochea, Patricia; Alegría Cía, Patricia; Rodríguez García, Antonio; Astrain Ulibarrena, David; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The need to reach a full energy decarbonisation is well known. Heating and cooling consumption is almost half of the global energy end-use. Thus, development of low-carbon and highly efficient power-to-heat technologies must be developed. In this work, the use of thermoelectric technology working as a heat pump is proposed to heat up an airflow of 38 m3/h. Two different prototypes of multistage thermoelectric heat pumps have been developed and compared based on monophasic and phase-change intermediate heat exchangers. The reduced thermal resistance obtained for the novel phase-change heat exchanger increases the heat flux supplied to the airflow and reduces the consumed power of the system, outperforming the operation of the monophasic thermoelectric heat pump between a 30 and a 67 %. The novel multistage phase-change heat pump obtains experimental COP values between 3.25 and 1.26 when the airflow rises its temperature from 3.5 °C to 23.5 °C. Additionally, this experimental study proves a new methodology to calculate the supplied heat flux to the airflow. The validation of this technology proves a discrepancy of ± 9 % when this novel technology is compared to the conventional one based on the airflow temperature rise.
Open Access
Performance assessment of an experimental CO2 transcritical refrigeration plant working with a thermoelectric subcooler in combination with an internal heat exchanger
(Elsevier, 2022) Casi Satrústegui, Álvaro; Aranguren Garacochea, Patricia; Araiz Vega, Miguel; Sánchez, Daniel; Cabello, Ramón; Astrain Ulibarrena, David; Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Gobierno de Navarra / Nafarroako Gobernua; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Regulations in the refrigeration sector are forcing the transition to low global warming potential fluids such as carbon dioxide in order to decrease direct greenhouse gases emissions. Several technologies have arisen over the past years to compensate the low performance of the transcritical carbon dioxide vapour compression cycle at high ambient temperatures. For low-medium power units, the inclusion of a thermoelectric subcooler or an internal heat exchanger have been proven as effective solutions for enhancing the coefficient of performance. However, the combination of a thermoelectric subcooler and an internal heat exchanger working simultaneously is yet to be explored theoretically or experimentally. This work presents, for the first time, an experimental transcritical carbon dioxide refrigeration facility that works simultaneously with a thermoelectric subcooler and with an internal heat exchanger in order to boost the cooling capacity and coefficient of performance of the refrigeration system. The experimental tests report improvements at optimum working conditions of 22.4 % in the coefficient of performance and an enhancement in the cooling capacity of 22.5 %. The 22.4 % increase in coefficient of performance would result in a decrease of energy consumption along a reduction of the greenhouse gases emissions. The proposed combination of a thermoelectric subcooler and an internal heat exchanger outperforms each of the technologies on their own and presents itself as a great controllable solution to boost the performance and reduce the greenhouse gasses emissions of transcritical carbon dioxide refrigeration cycles.
Open Access
Geothermal thermoelectric generator for Timanfaya National Park
(2019) Catalán Ros, Leyre; Astrain Ulibarrena, David; Aranguren Garacochea, Patricia; Araiz Vega, Miguel; Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería
Despite being one of the largest renewable sources, geothermal energy is not widely utilized for electricity generation. In the case of shallow Hot Dry Rock (HDR) fields, thermoelectric generators can entail a sustainable alternative to Enhanced Geothermal Systems (EGS). The present work studies two configurations of thermoelectric generators for Timanfaya National Park (Spain), one of the most important Hot Dry Rock fields in the world, with temperatures of 500°C at only 3 meters deep. The first configuration includes biphasic thermosyphons as heat exchangers for both sides, leading to a completely passive thermoelectric generator. The second configuration uses fin dissipators as cold-side heat exchangers.
Open Access
Experimental study of a multistage thermoelectric heat pump using different internal heat exchangers
(2021) Erro Iturralde, Irantzu; Aranguren Garacochea, Patricia; Astrain Ulibarrena, David; Ingeniería; Institute of Smart Cities - ISC; Ingeniaritza
The current need to carry out an energy transition towards a 100 % renewable horizon places the energy storage as the key. Thermal energy storage has the potential to be an optimal technology. Nowadays electrical resistors are used to convert electrical energy to termal energy by heating an air flux which is stored afterwards. In this work, it is proposed to use a multistage thermoelectric heat pump (MS-TEHP) to do this energy conversion. It has been experimentally analyzed and compared the performance of two MS-TEHP with different internal heat exchangers. With this preliminary research, it has been demonstrated the feasibility of this novel thermoelectric technology which aim is to improve the energy conversión process for thermal energy storage.
Open Access
Energía sostenible: sin malos humos
(Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, 2019) Samanes Pascual, Javier; Pascual Miqueleiz, Julio María; Berrueta Irigoyen, Alberto; Araiz Vega, Miguel; Catalán Ros, Leyre; Aranguren Garacochea, Patricia; Arricibita de Andrés, David; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Ingeniaritza
¿Puede España ser sostenible energéticamente? Si alguna vez te has planteado esta pregunta, o quieres saber en qué gastamos la energía y de dónde podría ser obtenida, aquí encontrarás respuestas. Nuestros recursos renovables son inmensos, pero también lo es nuestro consumo. Este libro no solo se centra en analizar la situación actual y las posibilidades que las energías renovables tienen en nuestro país, sino que, presentando de forma clara los datos sobre nuestro gasto energético, permite a cada lector identificar sus mayores consumos, de tal forma que pueda considerar cómo reducirlos. Energía sostenible. Sin malos humos es la adaptación al caso español, actualizando los datos, del libro publicado hace una década por David MacKay en el Reino Unido. La sostenibilidad es hoy en día una preocupación creciente en la sociedad. Pero a menudo este interés se ve contaminado por cifras enormes que resultan muy complicadas de comprender. Además, todos hemos oído hablar en algún momento sobre pequeños gestos al alcance de nuestra mano que podrían permitir un cambio hacia un modelo sostenible. Nada más lejos de la realidad, pequeñas acciones solo permiten pequeños cambios, y el cambio de modelo energético al que nos enfrentamos requiere grandes acciones. Para deshacernos de todo este ruido, en este libro se presentan los números de forma clara y sencilla, utilizando unidades a nuestro alcance y que son comprensibles por todas las personas. Esto permite identificar de una forma mucho más personal los consumos energéticos de nuestro día a día. A lo largo de la primera parte del libro se van construyendo dos columnas: una de color rojo, que representa la agregación de consumos, y otra de color verde, que representa la capacidad de generación. Estas columnas ofrecen una comparación muy visual de la infraestructura renovable que sería necesaria para mantener nuestro ritmo de consumo energético actual. Además, utiliza números «gordos» obtenidos de la experiencia del día a día. Por ejemplo, para calcular la capacidad de generación eólica se parte de una velocidad de viento estimada a partir de la velocidad típica de un ciclista urbano. Toda esta información se encuentra en la primera parte del libro, en los capítulos del 1 al 18. Sin embargo, este libro no se centra únicamente en el análisis de la situación actual, sino que da un paso más y propone alternativas al modelo energético actual con el fin de alcanzar un modelo 100% renovable a medio plazo. Estas medidas incluyen un aumento importante en la potencia renovable instalada, un aumento en la eficiencia energética y algunos ligeros cambios en nuestro estilo de vida que permitan una reducción del consumo. Por supuesto, los tres frentes deben ser atacados al mismo tiempo. Estas propuestas se recogen en la segunda parte del libro, en los capítulos 19 a 32. Por último, este es un libro divulgativo al alcance de todas las personas, que busca transmitir toda la información de forma clara e intuitiva sin perderse en complicados cálculos. Pero si eres de los que les gustan las cuentas, al final del libro encontrarás un apartado en el que se explica de forma rigurosa muchos de los cálculos simples realizados en las primeras partes del libro. Estos apéndices técnicos forman la tercera parte del libro, son los apéndices de la A hasta la H.
Open Access
Thermoelectric generator with passive biphasic thermosyphon heat exchanger for waste heat recovery: design and experimentation
(MDPI, 2021) Araiz Vega, Miguel; Casi Satrústegui, Álvaro; Catalán Ros, Leyre; Aranguren Garacochea, Patricia; Astrain Ulibarrena, David; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
One of the measures to fight against the current energy situation and reduce the energy consumption at an industrial process is to recover waste heat and transform it into electric power. Thermoelectric generators can be used for that purpose but there is a lack of experimental studies that can bring this technology closer to reality. This work presents the design, optimizations and development of two devices that are experimented and compared under the same working conditions. The hot side heat exchanger of both generators has been designed using a computational fluid dynamics software and for the cold side of the generators two technologies have been analysed: a finned dissipater that uses a fan and free convection biphasic thermosyphon. The results obtained show a maximum net generation of 6.9 W in the thermoelectric generator with the finned dissipater; and 10.6 W of power output in the generator with the biphasic thermosyphon. These results remark the importance of a proper design of the heat exchangers, trying to get low thermal resistances at both sides of the thermoelectric modules, as well as, the necessity of considering the auxiliary consumption of the equipment employed.
Open Access
Gamification and a low-cost laboratory equipment aimed to boost vapor compresion refrigeration learning
(OmniaScience, 2022) Aranguren Garacochea, Patricia; Sánchez, Daniel; Casi Satrústegui, Álvaro; Araiz Vega, Miguel; Catalán Ros, Leyre; Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The nowadays European educational framework boosts applying the learned theoretical concepts to real situations. Hence, practice sessions are key resources to present students direct applications of the theoretical concepts shown in class. Thus, developing new educational equipment and practice sessions oriented to bringing theoretical knowledge closer to practice should be one of the objectives of teachers. The present work describes a solution proposed by lectures of two Spanish universities looking to increase the knowledge of their engineering students. Along the years, these docents have noticed the lack of connection between the theoretical and practical knowledge among their students, drastically harming their learning procedure. Thus, in order to deepen into practical learning, a teaching methodology involving low-cost prototypes of vapor compression systems and a gamification method to help the students understand the concepts is proposed. The proposed methodology is expected to make a big positive impact on the results obtained by the students, taking into account the preliminary results reached.
Open Access
Enhancement of the power-to-heat energy conversion process of a thermal energy storage cycle through the use of a thermoelectric heat pump
(Elsevier, 2024) Erro Iturralde, Irantzu; Aranguren Garacochea, Patricia; Sorbet Presentación, Francisco Javier; Bonilla-Campos, Íñigo; Astrain Ulibarrena, David; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The principal strategy for achieving a neutral climate entails enhancing the share of renewable energies in the energy mix, in conjunction with promoting innovation in efficient technologies. Thermal energy storage systems have the potential to efficiently handle the intermittent nature of renewable energy sources. Furthermore, these systems can effectively handle shifts in both heat and electrical demand. Thus, efficient power-to-heat technologies are needed to boost thermal energy storage. This manuscript explores the potential of utilising a thermoelectric heat pump system in conjunction with electric resistances for charging a thermal energy storage. In order to achieve elevated temperatures, the thermoelectric system integrates thermoelectric heat pump blocks in a two-stage configuration. Air has been employed as a heat transfer medium for sensible heat storage. Higher airflow rates improve the performance of thermoelectric heat pump system. Moreover, its impact on the optimal voltage supply of the thermoelectric system is observed when it is combined with an electric resistance to achieve elevated temperatures. In comparison to the basic charging process that solely relies on the electric resistance of a thermal energy storage at 120 °C, a significant 30 % increase in power-to-heat energy conversion has been achieved by including the thermoelectric heat pump system. In fact, it efficiently elevates the temperature from the initial ambient temperature of 25 °C to a remarkable 113.1 °C, achieving a coefficient of performance of 1.35 with an airflow rate of 23 m3/h. Therefore, the use of this technology to enhance a complete process of storing excess renewable energy in the form of heat for subsequent use in both heat and electricity through a combined heat and power cycle is demonstrated.
Open Access
Net thermoelectric power generation improvement through heat transfer optimization
(Elsevier, 2017) Aranguren Garacochea, Patricia; Astrain Ulibarrena, David; Rodríguez García, Antonio; Martínez Echeverri, Álvaro; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Thermoelectric generation contributes to obtain a more sustainable energetic system giving its potential to harvest waste heat and convert it into electric power. In the present study a computational optimal net generation of 108.05 MWh/year was produced out of the flue gases of a real tile furnace located in Spain (the equivalent to supply the energy to 31 Spanish dwellings). This maximum generation has been obtained through the optimization of the hot and cold heat exchangers, the number of thermoelectric modules (TEMs) installed and the mass flows of the refrigerants, including the temperature loss of the flue gases and the influence of the heat power to dissipate over the heat dissipators. The results are conclusive, the installation of more TEMs does not always imply higher thermoelectric generation, so the occupancy ratio (δ) has to be optimized. The optimal generation has been achieved covering the 42 % of the surface of the chimney of the tile furnace with TEMs and using heat pipes on the cold side, which present smaller thermal resistances than the finned dissipators for similar consumptions of their fans. Moreover, the high influence of the consumption of the auxiliary equipment shows the importance of considering it to obtain realistic usable electric energy from real applications.