Person:
Pérez de Landazábal Berganzo, José Ignacio

Loading...
Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Pérez de Landazábal Berganzo

First Name

José Ignacio

person.page.departamento

Ciencias

person.page.instituteName

InaMat2. Instituto de Investigación en Materiales Avanzados y Matemáticas

ORCID

0000-0003-1172-6141

person.page.upna

1681

Name

Search Results

Now showing 1 - 4 of 4
  • PublicationOpen Access
    Room temperature huge magnetocaloric properties in low hysteresis ordered Cu-doped Ni-Mn-In-Co alloys
    (Elsevier, 2022) La Roca, Paulo Matías; López García, Javier; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Rodríguez Velamazán, José Alberto; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Gobierno de Navarra / Nafarroako Gobernua, PC017–018 AMELEC
    The reduction of the thermal hysteresis in first order magnetostructural transition is a determining factor to decrease energy losses and to improve the efficiency of magnetocaloric cooling based systems. In this work, a Cu doped NiMnInCo metamagnetic shape memory alloy (MMSMA) exhibiting a narrow thermal hysteresis (around 5 K) at room temperature has been designed. In this alloy, the induced L21 ordering process affects the phase stability in an unusual way compared to that observed in NiMnInCo and other NiMn based alloys. This ordering produces an increase in the Curie temperature of the austenite but hardly affects the mar tensitic transformation temperatures. As a consequence, the ordering increases the magnetization of the austenite without changing the transformation temperatures, doubles the sensitivity of the transformation to magnetic fields (the Claussius-Clapeyron slope goes from 2.1 to 3.9 K/T), improves the magnetocaloric effect, the reversibility and finally, enhances the refrigeration capacity. In addition, the magnetic hysteresis losses are among the lowest reported in the literature and the effective cooling capacity coefficient RCeff reaches 86 J/Kg for 2 T (15 % higher than those found in Ni-Mn based alloys) and 314 J/Kg for 6 T fields. Therefore, the ordered alloy possesses an excellent combination of low thermal hysteresis and high RCeff, not achieved previously in metamagnetic shape memory alloys near room temperature.
  • PublicationOpen Access
    Magnetocaloric effect enhancement driven by intrinsic defects in a Ni45Co5Mn35Sn15 alloy
    (Elsevier, 2019) Sánchez-Alarcos Gómez, Vicente; López García, Javier; Unzueta, Iraultza; Pérez de Landazábal Berganzo, José Ignacio; Recarte Callado, Vicente; Beato López, Juan Jesús; García, José Ángel; Plazaola, Fernando; Rodríguez Velamazán, José Alberto; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física
    The influence of mechanically-induced defects on the magnetostructural properties is analyzed in a Ni-Co-Mn-Sn alloy subjected to soft milling and subsequent annealing treatments. It is found that, opposite to what occurs in Ni-Mn-Sn ternary alloys, the annealing treatment affects the magnetic properties in a different way in martensite and in austenite. In particular, the saturation magnetization significantly increases in martensite after annealing whereas just a very slight variation is observed in austenite. This leads to the interesting fact that the presence of microstructural defects, far for worsening, makes the magnetocaloric effect to be higher in the as-milled state than after annealing. This behavior is explained as the result of the combination of the effect of defects on the Mn-Mn distance, the effect of Co on the magnetic exchange coupling between Mn atoms, and the effect of defects on the vibrational entropy change at the martensitic transformation.
  • PublicationOpen Access
    Correlation between particle size and magnetic properties in soft-milled Ni45Co5Mn34In16 powders
    (Elsevier, 2021) Khanna, Deepali; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Gobierno de Navarra / Nafarroako Gobernua, PC017-018 AMELEC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    The effect of microstructural defects induced by mechanical milling has been studied in a Ni–Mn–In–Co metamagnetic shape memory alloy. The martensitic transformation and Curie temperatures do not change with grinding, thus pointing out to a null variation of long range atomic order as a consequence of the deformation. Nevertheless, the enthalpy change of the martensitic transformation highly decreases. This, and the large thermal stabilization of the martensite (with shifts on the temperature of the first reverse martensitic transformation up to 60 K), indicate the presence of a huge amount of internal stresses and microstructural defects in the obtained micro-particles. The presence of such defects considerably affects the saturation magnetization in austenite whereas almost no effect is observed in martensite. The magnetocaloric effect has been evaluated in samples with three different particle sizes. In spite of the MCE value is lower than in the bulk, the broader temperature range for the martensitic transformation in the powders makes the relative cooling power be comparable to that in the bulk. The as-milled micro-particles can be then considered as good preliminary candidates for magnetic refrigeration applications at the microscale.
  • PublicationOpen Access
    Influence of structural defects on the properties of metamagnetic shape memory alloys
    (MDPI, 2020) Pérez de Landazábal Berganzo, José Ignacio; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Lambri, Osvaldo Agustín; López García, Javier; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
    The production of µ-particles of Metamagnetic Shape Memory Alloys by crushing and subsequent ball milling process has been analyzed. The high energy involved in the milling process induces large internal stresses and high density of defects with a strong influence on the martensitic transformation; the interphase creation and its movement during the martensitic transformation produces frictional contributions to the entropy change (exothermic process) both during forward and reverse transformation. The frictional contribution increases with the milling time as a consequence of the interaction between defects and interphases. The influence of the frictional terms on the magnetocaloric effect has been evidenced. Besides, the presence of antiphase boundaries linked to superdislocations helps to understand the spin-glass behavior at low temperatures in martensite. Finally, the particles in the deformed state were introduced in a photosensitive polymer. The mechanical damping associated to the Martensitic Transformation (MT) of the particles is clearly distinguished in the produced composite, which could be interesting for the development of magnetically-tunable mechanical dampers.