Open Access
Asymmetrically and symmetrically coated tapered optical fiber for sensing applications
(SPIE, 2015) Del Villar, Ignacio; Socorro Leránoz, Abián Bentor; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
The deposition of a non-metallic thin-film in a symmetrically coated tapered optical fiber leads to the generation of resonances due to guidance of a mode in the thin-film. At certain conditions, the resonances overlap each other, which can be avoided with an asymmetric coated tapered optical fiber, which permits to obtain resonances for TM and TE polarization separately. Numerical results showing the sensitivity to coating thickness and surrounding medium refractive index are also presented for both polarizations.
Open Access
Increasing the sensitivity of an optic level sensor with a wavelength and phase sensitive single-mode multimode single-mode (SMS) fiber structure
(IEEE, 2017) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Vento Álvarez, José Raúl; Socorro Leránoz, Abián Bentor; Gallego Martínez, Elieser Ernesto; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The sensitivity of a liquid level sensor based on a single-mode-multimode-single-mode fiber structure has been increased by hydrofluoric acid etching. The etching process was analyzed and monitored both theoretical and experimentally, which permitted to observe that a sinusoidal spectrum can be obtained for low diameters. As an example, a 2.77 fold sensitivity increase was attained by etching from diameter 125 to 50 μm. Moreover, the sinusoidal shape of the optical spectrum permitted to monitor liquid level changes both in wavelength and phase. The cross sensitivity of the sensor to refractive index and temperature was also studied.
Embargo
Photoisomerization-induced LMR shift for UV radiation detection
(Elsevier, 2024) Gallego Martínez, Elieser Ernesto; Ruiz Zamarreño, Carlos; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This work presents an optical sensor for ultraviolet radiation (UV) detection, based on the combined effects of Lossy Mode Resonance (LMR) in the mid infrared (MIR) spectral region and the photoisomerization of a polymeric dye coating. LMR was obtained by means of a sputtered SnO2 thin film on a tetrafluoroethylene-perfluoro (or alkoxy Vinyl Ether, PFA) substrate, along with a photo sensitive coating based on poly R-478. Obtained devices shown response and recovery times of 12 and 43 s, respectively, for an UV excitation of 71 mW at 365 nm. Sensitivity as a function of the excitation wavelength was studied with the highest value of 26 nm/mW obtained at 280 nm. For this excitation wavelength, the limit of detection (LoD) obtained was 0.024 mW. Four different excitation wavelengths were used to cover all UV regions (280, 310, 365 and 395 nm). All measurements were performed at room temperature and humidity (25 ¿C ± 1 ¿C and 13% R.H. ± 2% R.H. respectively). As far as we know, it is the first time that the LMR effect has been recognized in combination with a photoisomerization process.
Open Access
Lossy mode resonances biosensor for the detection of C-reactive protein
(Optica Publishing Group, 2016) Zubiate Orzanco, Pablo; Ruiz Zamarreño, Carlos; Sánchez Zábal, Pedro; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The fabrication and characterization of optical fiber biosensor based on Lossy Mode Resonances (LMR) to detect C-reactive protein (CRP) are presented. Indium tin oxide (ITO) coatings deposited on side-polished D-shaped optical fibers are used as LMR supporting coatings. The aptamer was immobilized on the ITO film using the Layer-by-Layer (LbL) nano-assembly process. The optical fiber sensor presented shows a high selectivity and low limit detection.
Open Access
Sensitivity enhancement by diameter reduction in low cutoff wavelength single-mode multimode singlemode (SMS) fiber sensors
(IEEE, 2017) Goñi Carnicero, Jaime; Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Two different low cutoff wavelength single-mode fibers were used in single-mode multimode single-mode (SMS) configuration with the aim of designing sensors operating at short wavelengths, where optical sources and spectrometers are less expensive than in telecommunications bands. The diameter of the SMS structure was reduced with an etching process based on hydrofluoric acid immersion. The results prove that the devices can operate at wavelength ranges from 600 to 1200 nm and that multiple peaks can be obtained, each one with a different sensitivity that is proportional to the wavelength. Moreover, a fivefold increase in sensitivity to refractive index can be obtained. This high sensitivity indicates the possibility to apply this simple and cost-effective device in other applications such as biosensors or chemical sensors.
Open Access
High sensitivity lossy-mode resonance refractometer using low refractive index PFA planar waveguide
(Elsevier, 2023) Domínguez Rodríguez, Ismel; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ascorbe Muruzabal, Joaquín; Del Villar, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work a new strategy to improve the sensitivity of refractometers based on lossy-mode resonances has been proved. The proximity of the PFA (tetrafluoroethylene-perfluoro polymer) substrate refractive index to that of water has permitted to implement an optical refractometer with a sensitivity of 41,034 nm per refractive index unit (nm/RIU) for refractive indices ranging from 1.3318 to 1.3347. The work is supported with both theoretical and experimental results. This high sensitivity can be used for the development of LMR based chemical sensors and biosensors, where a low limit of detection is required, with the additional advantage of a simple disposable planar configuration.
Open Access
Beyond near-infrared lossy mode resonances with fluoride glass optical fiber
(Optica, 2021) Vitoria Pascual, Ignacio; Ruiz Zamarreño, Carlos; Ozcariz Celaya, Aritz; Imas González, José Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The objective of this Letter consists of the exploration of the lossy mode resonance (LMR) phenomenon beyond the nearinfrared region and specifically in the short wave infrared region (SWIR) and medium wave infrared region (MWIR). The experimental and theoretical results show for the first time, to the best of our knowledge, not only LMRs in these regions, but also the utilization of fluoride glass optical fiber associated with this phenomenon. The fabricated devices consist of a nanometric thin-film of titanium dioxide used as LMR generating material, which probed extraordinary sensitivities to external refractive index (RI) variations. RI sensitivity was studied in the SWIR and MWIR under different conditions, such as the LMR wavelength range or the order of resonance, showing a tremendous potential for the detection of minute concentrations of gaseous or biological compounds in different media.
Open Access
Fiber optic ammonia sensor using Bromocresol Green pH indicator
(IEEE, 2014-12-15) Rodríguez Rodríguez, Adolfo Josué; May Arrioja, Daniel A.; Domínguez Cruz, René; Ruiz Zamarreño, Carlos; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
We report a fiber optic sensor for low levels of ammonia gas detection based on the use a Bromocresol Green (BCG) pH indicator attached to the optical fiber employing hydrophobic and gas permeable polyurethane film named Tecoflex® as attraping matrix. Highly reproducible and reversible fiber optical sensors have been achieved employing simple and short fabrication processes. The advantage for employ a BCG pH indicator is to take advantage of the basicity of ammonia exhibiting a wide spectral response (500 nm-750 nm) and shows recovery times of less than 15 s. The Tecoflex® film provides additional advantages to be measured to the sensitive area of the sensor, such as operation even in extremely dry environments, efficient transport and prevent leakage or detachment of the BCG pH indicator. The combination of the BCG pH indicator and Tecoflex® film provides a reliable and robust fiber optic ammonia gas sensor.
Open Access
Resonance-based optical gas sensors
(IEEE, 2025-07-02) Gallego Martínez, Elieser Ernesto; Ruiz Zamarreño, Carlos; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Gas sensors play a critical role in numerous human activities. Their necessity continues to grow across diverse fields as technological advancements drive demand for precision agriculture and bioengineering among other applications. Among existing sensor technologies, optical gas sensors stand out due to their ability to operate remotely in high-risk environments while remaining unaffected by electromagnetic interference. Resonance-based optical sensors offer targeted gas detection through the functionalization of their sensitive surfaces. This work focuses on reviewing the state of the art in resonance-based optical gas sensors (ROGSs), addressing their fundamental principles, recent advances in fabrication processes, waveguide designs, and materials employed both for resonance generation and as sensitive coatings. In addition, the review examines achieved sensitivity, emerging applications, and key developments in the field, including those efforts on improving ROGS performances by means of artificial intelligence techniques. The study encompasses optical sensors leveraging surface plasmon resonance, lossy mode resonance, and hyperbolic mode resonance¿the latter representing a notable breakthrough in recent years as a particular case of Bloch surface waves.
Embargo
Ag@Fe3O4-coated U-shaped plastic optical fiber sensor for H2S detection
(Elsevier, 2024) López Vargas, Juan David; Dante, Alex; Allil, Regina C.; Del Villar, Ignacio; Matías Maestro, Ignacio; Werneck, Marcelo M.; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This work presents the fabrication of U-shaped plastic optical fiber (POF) sensors for hydrogen sulfide (H2S) detection, coated with Fe3O4 nanoparticles synthetized using the Pulsed Laser Ablation in Liquid (PLAL) technique. The Fe3O4 nanoparticles were synthetized in ultra-pure water and in silver nitrate solution, resulting in two colloidal samples with different morphological, optical, and structural properties. The Fe3O4 nanoparticles were coated onto one POF sensor, while the other sensor was coated with a nanostructure composed of Ag as the core and Fe3O4 as the shell (Ag@Fe3O4). The performance of both sensors was evaluated by exposing them to different concentrations of H2S and other gases such as CH4, H2, and CO2. All experiments were conducted at 25 °C. Results showed that the sensor coated with Ag@Fe3O4 was 12 times more sensitive to H2S compared to the sensor coated with Fe3O4, with a detection limit of 1 ppm and a rise time of 15 s. Moreover, the POF sensor coated with Ag@Fe3O4 presented high selectivity to H2S, making it a promising candidate for H2S detection in different applications. The sensor's performance was also evaluated with a relative humidity range of 20–90%, exhibiting a minimal 0.75% signal variation at 90% humidity.