Open Access
Photocatalytic degradation of trimethoprim on doped Ti-pillared montmorillonite
(Elsevier, 2019) González, Beatriz; Trujillano, Raquel; Vicente, Miguel Ángel; Rives, Vicente; Korili, Sophia A.; Gil Bravo, Antonio; Institute for Advanced Materials and Mathematics - INAMAT2
Montmorillonite pillared with titanium and doped with Cr3+ or Fe3+ has been tested for the photo-degradation of the antibiotic trimethoprim (trimethoxybenzyl-2,4-pyrimidinediamine) under different conditions, namely, in the dark or in UV light, with or without catalyst, finding excellent catalytic performance under photocatalytic conditions. The degradation by-products were preliminary analysed by mass spectrometry. The results suggested that the molecule broke in two halves, corresponding to its two existing rings. The process continued with the breakage of new fragments from the trimethoxybenzene half, these fragments later reacted with the methoxy groups in this part of the molecule, giving species with m/z values higher than that for the starting molecule, and with the breakage of new fragments.
Open Access
Optimizing the removal of nitrate by adsorption onto activated carbon using response surface methodology based on the central composite design
(Taylor & Francis, 2020) Taoufik, Nawal; Elmchaouri, Abdellah; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
This study sheds light on the adsorption process for the removal of nitrate ions from synthetic aqueous solutions. This contaminant pose a potential risk to the environment and can cause health effects including cancers and methemoglobinemia in infants. When the adsorption process is carried out, the effect by the several operating parameters such as initial nitrate concentration, pH, mass of activated carbon, and contact time becomes apparent. The essential process variables are optimized using response surface methodology (RSM) based on the central composite design (CCD) experiments. For this purpose 31 experimental results are required to determine the optimum conditions. The optimum conditions for the removal of nitrates is found to be: initial nitrate concentration = 15 mg/L; initial pH 4.0; mass of activated carbon = 25 mg, and contact time = 70 min. At these optimized conditions, the maximum removal of nitrates is found to be 96.59%.
Open Access
Adsorption recovery of Ag(I) and Au(III) from an electronics industry wastewater on a clay mineral composite
(University of Science and Technology Beijing, 2019) Rakhila, Youness; Elmchaouri, Abdellah; Mestari, Allal; Korili, Sophia A.; Abouri, Meriem; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The aim of this work is to investigate the ability of an adsorbent of a clay mineral composite to remove and recover gold and silver ions from wastewater. The composite was prepared by mixing phosphogypsum (PG), obtained from an industrial waste, and a natural clay mineral. The materials were characterized before and after use in adsorption by several techniques. Batch adsorption experiments were carried out, and the effects of the contact time and the pH and temperature of solution on the removal processes were investigated. The optimum pH for the adsorption was found to be 4. The adsorption of these metal ions reached equilibrium after 2 h of contact. The pseudo-first- and the pseudo-second-order kinetic models, as well as the Freundlich and the Langmuir isotherm equations, were considered to describe the adsorption results. The maximum adsorbed amount of 85 mg·g−1 Ag(I) and 108.3 mg·g−1 Au(III) was found. The recovery of the adsorbed gold and silver ions from the adsorbent was also analyzed. Strong acids appeared to be the best desorption agents to recover gold and silver ions. The use of aqua regia gave regeneration rates close to 95.3% and 94.3% for Ag(I) and Au(III), respectively. Finally, the removal of gold and silver ions from an industrial wastewater was tested in batch experiments, and percentage recoveries of 76.5% and 79.9% for Ag(I) and Au(III), respectively, were obtained. To carry out the industrial application of the proposed methodology, an economic viability study is required.
Open Access
Progress in the synthesis and applications of hexaaluminate-based catalysts
(Taylor & Francis, 2020) Torrez Herrera, Jonathan Josué; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The development of materials that can exhibit thermal resistance at very high temperatures, thus allowing them to be applied as catalysts and thermal insulators, amongst other possible uses, is a research subject of great interest. This is the case for hexaaluminates, a class of hexagonal aluminate compounds with a unique structure that are stable at very high temperatures up to 1600°C and exhibit exceptional resistance to sintering and thermal shock, thus making them attractive catalysts for high-temperature applications. In this review, the structure of hexaaluminates is presented first. The most recent advances in synthetic methods (sol-gel, reverse microemulsion, hydrothermal synthesis, carbon-templating, solution combustion synthesis, and freeze-drying methods) are discussed subsequently, with the aim of maximizing textural properties and including in their structure metals known to be active in catalytic applications, such as combustion of CH4, partial oxidation, and dry reforming of CH4 to produce synthetic gas, and the decomposition of N2O. Finally, other applications, such as their function as a thermal barrier, are also addressed.
Open Access
Progress in the removal of pharmaceutical compounds from aqueous solution using layered double hydroxides as adsorbents: a review
(Elsevier, 2020) Santamaría Aquilué, Rafael; Vicente, Miguel Ángel; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Emerging contaminants and, among them, pharmaceutical compounds, have a significant impact on water ecosystems. Layered Double Hydroxides (LDH), being easy to synthesize and cheap materials, have recently gained attention as adsorbents in aqueous solutions. This work describes the latest research performed in the adsorption capacity of LDH towards both antibiotics and Non-Steroidal Anti-Inflammatory Drugs (NSAID) describing and analyzing the synthesis conditions (Me2+:Me3+ molar ratio, calcination temperature, choice of metals for the memory effect), kinetics and isotherm models used, use of support (more practical in a 3D over a 2D form), temperature effect and several techniques for the recovery of the adsorbents. LDH exhibited great performance and potential as clean adsorbents for these emerging contaminants.
Embargo
Improvement of the adsorption properties of an activated carbon coated by titanium dioxide for the removal of emerging contaminants
(Elsevier, 2019) Taoufik, Nawal; Elmchaouri, Abdellah; Anouar, Fatna; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
Three activated carbon coated titanium dioxide composites are evaluated as adsorbents for the removal of three pharmaceutical compounds: clofibric, gallic and salicylic acids from aqueous solutions. These composite materials are characterized by several techniques as SEM, FT-IR, TGA and point of zero charge determination. The adsorption mechanism of acids was investigated and compared to the adsorption on the virgin carbon. The analysis of adsorption isotherms and kinetic properties reveals that the addition of TiO2 increased the adsorption capacities of the initial material. The adsorption kinetics has been studied in terms of pseudo-first and pseudo-second order kinetic models, and the Freundlich, Langmuir, Temkin, Tôth and Sips isotherms models have also been applied to the equilibrium adsorption data. The analysis of results indicated that the adsorption of acids on the activated carbon-titanium dioxide composites is well described by the pseudo-first order kinetic model and the Sips isotherm equation fitted the sorption experimental results better than other models.
Open Access
White and red Brazilian Sao Simao's kaolinite-TiO2 nanocomposites as catalysts for toluene photodegradation from aqueous solutions
(MDPI, 2019) Mora, Lucas D.; Trujillano, Raquel; Rives, Vicente; Pérez Bernal, María Elena; Korili, Sophia A.; Gil Bravo, Antonio; Faria, Emerson H. de; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The presence of volatile organic compounds in groundwater is a major concern when it is used as a drinking water source because many of these compounds can adversely affect human health. This work reports on the preparation and characterization of white and red Brazilian Sao Simao's kaolinite-TiO2 nanocomposites and their use as catalysts in the photochemical degradation of toluene, a significant volatile organic compound. The nanocomposites were prepared by a sol-gel procedure, using titanium bis(triethanolaminate)diisopropoxide as a precursor. Thermal treatments of the nanocomposites led to different polymorphic titania phases, while the clay changed from kaolinite to metakaolinite. This structural evolution strongly affected the photocatalytic degradation behavior-all the solids efficiently degraded toluene and the solid calcined at 400 degrees C, formed by kaolinite and anatase, showed the best behavior (90% degradation). On extending the photochemical treatment up to 48 h, high mineralization levels were reached. The advantage of photodegradation using the nanocomposites was confirmed by comparing the results from isolated components (titanium dioxide and kaolinite) to observe that the nanocomposites displayed fundamental importance to the photodegradation pathways of toluene.
Open Access
Saline slag waste as an aluminum source for the synthesis of Zn–Al–Fe–Ti layered double-hydroxides as catalysts for the photodegradation of emerging contaminants
(Elsevier, 2020) Santamaría Arana, Leticia; Vicente, Miguel Ángel; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa; Gobierno de Navarra / Nafarroako Gobernua, PI017-PI039 CORRAL
In this work, aluminum extracted from saline slag waste is valorized to create a layered double-hydroxide series containing zinc and various proportions of aluminum/titanium. Materials were synthesized by the co-precipitation method with an Me2+/Me3+ molar ratio of 3:1 and tested for the removal of diclofenac and salicylic acid from water under UV radiation. The incorporation of 5 wt% iron by wet impregnation is evaluated. In addition, another series of zinc, aluminum/iron materials with and without 5 wt% impregnated titanium are tested as catalysts for comparison. Structural characterization and comparison of the two series was performed by powder X-ray diffraction (PXRD), nitrogen adsorption at 77 K, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and temperature-programmed reduction (TPR) measurements. The uncalcinated samples had a typical hydrotalcite structure with a high crystallinity; the presence of ZnO, ZnFe2O4 or Fe3O4 was found after calcination. The specific surface areas of the dried samples ranged from 78 to 199 m2/g, being highest for Zn6Al0.5Ti1.5. Overall, the results showed that the ZnAlTi series were more effective catalysts than ZnAlFe for photodegradation of the emerging contaminants diclofenac and salicylic acid, under UV light at 298 K, considering two concentrations of the organic molecules (5 and 50 μmol/dm3).
Open Access
Effect of the surface properties of Me2+/Al layered double hydroxides synthesized from aluminum saline slag wastes on the adsorption removal of drugs
(Elsevier, 2020) Santamaría Arana, Leticia; Devred, F.; Gaigneaux, E. M.; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa; Gobierno de Navarra / Nafarroako Gobernua, PI017-PI039 CORRAL
This work presents the synthesis of Me2+ (Co, Mg, Ni and Zn)/Al layered double hydroxides (LDH) with a 3:1 M ratio by the co-precipitation method. Structural characterization and comparison of the series has been achieved using powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), nitrogen physisorption at 77 K, thermogravimetry measurements (TGA), temperature-programmed reduction (TPR), X-ray photoelectron spectroscopy (XPS), ammonia temperature-programmed desorption (NH3-TPD) and point of zero charge (pHpzc). Batch experiments were performed to analyze the adsorption capacity of the different LDH on diclofenac and salicylic acid, as example of emergent pollutants. The pH, mass of adsorbent, contact time and concentration of pollutant were the parameters used to compare the adsorption performance of the synthesized materials. Samples showed different behavior and the equilibrium was reached at different times, Mg6Al2 and Zn6Al2 showed lower equilibrium times but had higher adsorption capacity. Various adsorption and isotherm equation models were employed to study both the kinetic and equilibrium results and, in general, the removal of diclofenac was greater than that of salicylic acid. 1-Butanol conversion was also used as a means of acidity and basicity characterization and the results were compared with the adsorption performance of the samples in order to explain the results found. A relationship between the amount of pollutants adsorbed and the butenes formed in the dehydrogenation reaction of 1-butanol was found.
Open Access
Effect of high pressure on the reducibility and dispersion of the active phase of Fischer-Tropsch catalysts
(MDPI, 2019) Yunes, Simón; Vicente, Miguel Ángel; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The effect of high pressure on the reducibility and dispersion of oxides of Co and Fe supported on -Al2O3, SiO2, and TiO2 has been studied. The catalysts, having a nominal metal content of 10 wt.%, were prepared by incipient wetness impregnation of previously calcined supports. After drying at 60 °C for 6 h and calcination at 500 °C for 4 h, the catalysts were reduced by hydrogen at two pressures, 1 and 25 bar. The metal reduction was studied by temperature-programmed reduction up to 750 °C at the two pressures, and the metal dispersion was measured by CO chemisorption at 25 °C, obtaining values between 1% and 8%. The physicochemical characterization of these materials was completed by means of chemical analysis, X-ray diffraction, N2 adsorption-desorption at -196 °C and scanning electron microscopy. The high pressure lowered the reduction temperature of the metal oxides, improving their reducibility and dispersion. The metal reducibility increased from 42%, in the case of Fe/Al2O3 (1 bar), to 100%, in the case of Fe/TiO2 (25 bar).