Person: López Martín, Antonio
Loading...
Email Address
person.page.identifierURI
Birth Date
Research Projects
Organizational Units
Job Title
Last Name
López Martín
First Name
Antonio
person.page.departamento
Ingeniería Eléctrica, Electrónica y de Comunicación
person.page.instituteName
ISC. Institute of Smart Cities
ORCID
0000-0001-7629-0305
person.page.upna
2254
Name
43 results
Search Results
Now showing 1 - 10 of 43
Publication Open Access AC coupled amplifier with a resistance multiplier technique for ultra-low frequency operation(Elsevier, 2022) Martincorena Arraiza, Maite; Cruz Blas, Carlos Aristóteles de la; Carlosena García, Alfonso; López Martín, Antonio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate PublikoaThis paper proposes a novel, tunable AC coupled capacitive feedback amplifier, exhibiting an ultra-low high pass corner frequency. This is accomplished by actively boosting the output resistive value of a MOS transistor in weak inversion. The circuit is based on a more general architecture, recently proposed by the authors, and is analyzed in terms of its capability to achieve ultra-low frequency operation, its DC performance, and noise. The proposed technique is demonstrated via measurement results from a fabricated test chip prototype using a standard 0.18 µm CMOS technology. The proposed amplifier provides a tunable high pass corner frequency from 20 mHz to 475 mHz, consuming 4.71 μW and a total area of 0.069 mm2.Publication Open Access Super class AB RFC OTA with adaptive local common-mode feedback(Institution of Engineering and Technology, 2018) Garde Luque, María Pilar; López Martín, Antonio; Carvajal, Ramón G.; Ramírez-Angulo, Jaime; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónA super class AB recycling folded cascode operational transconductance amplifier is presented. It employs local common-mode feedback using two matched tuneable active resistors, allowing to adapt the amplifier to different process variations and loads. Measurement results from a test chip prototype fabricated in a 0.5 μm CMOS process validate the proposal.Publication Open Access Wide-swing class AB regulated cascode current mirror(IEEE, 2020) Garde Luque, María Pilar; López Martín, Antonio; Cruz Blas, Carlos Aristóteles de la; Carvajal, Ramón G.; Ramírez-Angulo, Jaime; Institute of Smart Cities - ISCA micropower regulated cascode CMOS current mirror is presented, combining floating gate and quasi floating gate MOS transistors to achieve both wide swing and class AB operation, respectively. Measurement results for a 0.5 μm CMOS test chip prototype are included, showing that the current mirror can provide a THD at 100 kHz of -44 dB for a supply voltage of ±0.75 V and input current amplitudes 20 times larger than the bias current.Publication Open Access Design of low-cost smart accelerometers(Universitat Politècnica de Catalunya, 2005) Carlosena García, Alfonso; López Martín, Antonio; Massarotto, Marco; Cruz Blas, Carlos Aristóteles de la; Lecumberri Villamediana, Pablo; Gómez Fernández, Marisol; Pintor Borobia, Jesús María; Gárriz Sanz, Sergio; Ingeniería Eléctrica y Electrónica; Matemáticas; Ingeniería Mecánica, Energética y de Materiales; Ingeniaritza Elektrikoa eta Elektronikoa; Matematika; Mekanika, Energetika eta Materialen IngeniaritzaThe goal of this project is to design a low-cost smart accelerometer, making use of a piezoelectric element as basic sensing material, and adding a mixed-mode conditioning circuit.Publication Open Access Low-power ultrasonic front-end for cargo container monitoring(IEEE, 2019) Algueta-Miguel, Jose M.; García Oya, José Ramón; López Martín, Antonio; Cruz Blas, Carlos Aristóteles de la; Muñoz Chavero, Fernando; Hidalgo Fort, Eduardo; Institute of Smart Cities - ISCA low-power ultrasonic communication system conceived for cargo container monitoring is presented. Two piezoelectric transducers operating at 40 kHz are used for generating and acquiring an ultrasonic signal through the metallic wall, thus establishing a non-invasive inside-outside communication that preserves the container integrity. Both transducers are fixed by means of a novel magnetic case designed for optimizing data transmission. The acoustic and electrical characteristics of the ultrasonic channel are analyzed. An experimental measurement setup based on FPGA has been implemented for comparing some basic modulation and detection schemes in terms of Bit Error Rate (BER), also considering their robustness against undesired mechanical and electromagnetic perturbations. On this basis, a compact digital DBPSK modulator using a square carrier signal is proposed. Frequency and amplitude tracking algorithms are designed for optimizing the quality and robustness of the data transmission. Finally, a low-power low-rate (up to few kbps) architecture based on the previous elements is presented. All the proposed contributions are experimentally validated.Publication Open Access Fault detection of planetary gears based on signal space constellations(MDPI, 2022) Martincorena Arraiza, Maite; Cruz Blas, Carlos Aristóteles de la; López Martín, Antonio; Molina Vicuña, Cristian; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónA new method to process the vibration signal acquired by an accelerometer placed in a planetary gearbox housing is proposed, which is useful to detect potential faults. The method is based on the phenomenological model and consists of the projection of the healthy vibration signals onto an orthonormal basis. Low pass components representation and Gram–Schmidt’s method are conveniently used to obtain such a basis. Thus, the measured signals can be represented by a set of scalars that provide information on the gear state. If these scalars are within a predefined range, then the gear can be diagnosed as correct; in the opposite case, it will require further evaluation. The method is validated using measured vibration signals obtained from a laboratory test bench.Publication Open Access Distributed opportunistic wireless mapping system towards smart city service provision(IEEE, 2021) Villadangos Alonso, Jesús; Falcone Lanas, Francisco Javier; López Martín, Antonio; Astrain Escola, José Javier; Sanchis Gúrpide, Pablo; Matías Maestro, Ignacio; Estatistika, Informatika eta Matematika; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Estadística, Informática y Matemáticas; Ingeniería Eléctrica, Electrónica y de ComunicaciónThe knowledge of wireless signal distribution within an urban scenario can provide useful information to users as well as to enhance connectivity and device operation or to perform municipal logistics based on crowd density and user mobility patterns. In this work, a distributed wireless mapping system, based on a combination of opportunistic nodes such as smartphones which map geolocated WiFi access point connection and received power levels, and a cloud-based information gathering architecture is described. The proposed system has been tested in the framework of the Smart City platform of the city of Pamplona, providing signal distribution heat maps, which can be used for multiple municipal services.Publication Open Access Energy-efficient amplifiers based on quasi-floating gate techniques(MDPI, 2021) López Martín, Antonio; Garde Luque, María Pilar; Algueta-Miguel, Jose M.; Beloso Legarra, Javier; González Carvajal, Ramón; Ramírez-Angulo, Jaime; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de ComunicaciónEnergy efficiency is a key requirement in the design of amplifiers for modern wireless applications. The use of quasi-floating gate (QFG) transistors is a very convenient approach to achieve such energy efficiency. We illustrate different QFG circuit design techniques aimed to implement low-voltage energy-efficient class AB amplifiers. A new super class AB QFG amplifier is presented as a design example including some of the techniques described. The amplifier has been fabricated in a 130 nm CMOS test chip prototype. Measurement results confirm that low-voltage ultra low power amplifiers can be designed preserving at the same time excellent small-signal and large-signal performance.Publication Open Access Energy harvesting approaches in IoT scenarios with very low ambient energy(European Association for the Development of Renewable Energy, Environment and Power Quality (EA4EPQ), 2019) López Martín, Antonio; Algueta-Miguel, Jose M.; Matías Maestro, Ignacio; Institute of Smart Cities - ISCThe feasibility of multi-source energy harvesting in Internet of Things (IoT) scenarios with low and intermittent ambient energy is addressed. As a relevant case study, application to a smart cargo container system is analysed. The most relevant features of the main energy sources available in this target application are identified, and various transducers adapted to such sources are evaluated. Measurement results indicate that combined piezoelectric and thermoelectric generation inside cargo containers can significantly extend the battery lifetime of IoT end nodes embedded in such containers.Publication Open Access Analog lock-in amplifier design using subsampling for accuracy enhancement in GMI sensor applications(MDPI, 2023) Algueta-Miguel, Jose M.; Beato López, Juan Jesús; López Martín, Antonio; Ciencias; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA2005A frequency downscaling technique for enhancing the accuracy of analog lock-in amplifier (LIA) architectures in giant magneto-impedance (GMI) sensor applications is presented in this paper. As a proof of concept, the proposed method is applied to two different LIA topologies using, respectively, analog and switching-based multiplication for phase-sensitive detection. Specifically, the operation frequency of both the input and the reference signals of the phase-sensitive detector (PSD) block of the LIA is reduced through a subsampling process using sample-and-hold (SH) circuits. A frequency downscaling from 200 kHz, which is the optimal operating frequency of the employed GMI sensor, to 1 kHz has been performed. In this way, the proposed technique exploits the inherent advantages of analog signal multiplication at low frequencies, while the principle of operation of the PSD remains unaltered. The circuits were assembled using discrete components, and the frequency downscaling proposal was experimentally validated by comparing the measurement accuracy with the equivalent conventional circuits. The experimental results revealed that the error in the signal magnitude measurements was reduced by a factor of 8 in the case of the analog multipliers and by a factor of 21 when a PSD based on switched multipliers was used. The error in-phase detection using a two-phase LIA was also reduced by more than 25%.