Open Access
Nanocoated optical fibre for lossy mode resonance (LMR) sensors and filters
(IEEE, 2015) Del Villar, Ignacio; Arregui San Martín, Francisco Javier; Corres Sanz, Jesús María; Bariáin Aisa, Cándido; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Elosúa Aguado, César; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Nanometer scale coatings with a complex refractive index deposited on optical fibre permit to obtain attenuation bands in the transmission spectrum, whose central wavelength coincides with the moment when a mode guided in the optical fibre cladding starts to be guided in the coating. Due to the complex refractive index of the coating, the guided mode is a lossy mode. Consequently, these attenuation bands receive the name of lossy mode resonances. This phenomenon can be used for development of ultra-high sensitivity photonic devices (for detection, among others, of volatile organic compounds, pH and refractive index) or for optical filtering. In this work, rules for adequate design are indicated based on numerical results obtained with FIMMWAVE and on experimental results that corroborate the theoretical predictions.
Open Access
Silver nanoparticles loaded electrospun nanofibers for humidity optical fiber sensing
(2012) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Rodríguez, Yoany; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
In this work, a new optical device based on silver loaded electrospun nanofibers (ENFs) for measuring Relative Humidity is proposed. Fiber mats composed of poly(acrylic acid) and β-cyclodextrin were deposited onto an optical fiber core by electrospinning. Afterwards the ENFs were submitted to a thermal curing. Then, the ENFs were loaded with Ag nanoparticles (Ag NPs) synthesized using a Ag+ loading step and a further reduction step with dimethylamine borane (DMAB). Several load/reduction cycles were performed. Ag NPs enhance significantly the optical response of the polymer-only fiber mats. The Ag NPs loaded ENF sensor was tested using controlled variations of Relative Humidity (RH). The results showed a very fast response of the absorbance spectra enabling high performance applications such as human breathing monitoring.
Open Access
Micro and nanostructured materials for the development of optical fibre sensors
(MDPI, 2017) Elosúa Aguado, César; Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Ruiz Zamarreño, Carlos; Corres Sanz, Jesús María; Bariáin Aisa, Cándido; Goicoechea Fernández, Javier; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Ozcariz Celaya, Aritz; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The measurement of chemical and biomedical parameters can take advantage of the features exclusively offered by optical fibre: passive nature, electromagnetic immunity and chemical stability are some of the most relevant ones. The small dimensions of the fibre generally require that the sensing material be loaded into a supporting matrix whose morphology is adjusted at a nanometric scale. Thanks to the advances in nanotechnology new deposition methods have been developed: they allow reagents from different chemical nature to be embedded into films with a thickness always below a few microns that also show a relevant aspect ratio to ensure a high transduction interface. This review reveals some of the main techniques that are currently been employed to develop this kind of sensors, describing in detail both the resulting supporting matrices as well as the sensing materials used. The main objective is to offer a general view of the state of the art to expose the main challenges and chances that this technology is facing currently.
Open Access
Electrospun nanofiber mats for evanescent optical fiber sensors
(Elsevier, 2013) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rivero Fuente, Pedro J.; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, a study about the optical response of electrospun nanofiber (ENF) coatings for their use in evanescent optical fiber sensors is presented. Several types of ENF mats composed of poly(acrylic acid) (PAA) were developed with different ENF diameters and densities. These ENF mats were deposited onto an optical fiber core in order to fabricate humidity evanescent optical fiber sensors. The devices were exposed to relative humidity (RH) variations from 30% RH to 95%RH. The transfer functions of the devices (transmitted optical power versus relative humidity) presented two well-differenced behaviors depending on the ENF diameter and the ENF mat density. The devices with lower ENF diameters and higher mat density showed an increase in the transmitted optical power when RH increased. On the contrary, the devices with higher ENF diameters and lower mat density showed a decrease in the transmitted optical power when RH increased. In addition to this, sensors with thinner ENF overlays, showed a higher sensitivity. In order to study the response time of these devices, the ENFs sensors were submitted to human breathing cycles and presented a response time around 340 ms (exhalation). In spite of the high RH conditions of this experiment, the devices showed a recovery time around 210 ms and a negligible hysteresis or drift with respect to the initial condition (inhalation).
Open Access
An antibacterial surface coating composed of PAH/SiO2 nanostructurated films by layer by layer
(Wiley, 2010) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Ruete Ibarrola, Leyre; Goicoechea Fernández, Javier; Fernández Valdivielso, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
In this work we propose a novel antibacterial coating composed of SiO2 and the polymer Poly(allylamine hydrochloride) (PAH). The coating was fabricated by the technique Layer-by-Layer (LbL). This technique has already been used in previous works, and it has the advantage that it allows to control the construction of nanosized and well organized multilayer films. Here, the new nanotexturized LbL SiO2 surface acts as antibacterial agent. The fabricated coatings have been tested in bacterial cultures of genus Lactobacillus to observe their antibacterial properties. It has been demonstrated these PAH/SiO2 coating films have a very good antimicrobial behaviour against this type of bacteria.
Open Access
Humidity sensor based on silver nanopartlcles embedded in a polymeric coating
(Sciendo, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería; Ingeniaritza; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
In this work, it is presented a novel optical fiber humidity sensor based on silver nanoparticle-loaded polymeric coatings built onto an optical fiber core. The polymeric film was fabricated using the Layer-by-Layer assembly technique. The silver nanoparticles (Ag NPs) were characterized using transmission electron microscopy (TEM and UV-VIS spectroscopy. A Localized Surface Plasmon Resonance (LSPR) attenuation band is observed when the thickness of the coating increases, and showed a very good sensitivity to Relative Humidity (RH) variations, suitable for high performance applications such as human breathing monitoring.
Open Access
Layer-by-layer nano-assembly: a powerful tool for optical fiber sensing applications
(MDPI, 2019) Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Ingeniaritza; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Ingeniería; Ingeniería Eléctrica, Electrónica y de Comunicación
The ability to tune the composition of nanostructured thin films is a hot topic for the design of functional coatings with advanced properties for sensing applications. The control of the structure at the nanoscale level enables an improvement of intrinsic properties (optical, chemical or physical) in comparison with the traditional bulk materials. In this sense, among all the known nanofabrication techniques, the layer-by-layer (LbL) nano-assembly method is a flexible, easily-scalable and versatile approach which makes possible precise control of the coating thickness, composition and structure. The development of sensitive nanocoatings has shown an exceptional growth in optical fiber sensing applications due to their self-assembling ability with oppositely charged components in order to obtain a multilayer structure. This nanoassembly technique is a powerful tool for the incorporation of a wide variety of species (polyelectrolytes, metal/metal oxide nanoparticles, hybrid particles, luminescent materials, dyes or biomolecules) in the resultant multilayer structure for the design of high-performance optical fiber sensors. In this work we present a review of applications related to optical fiber sensors based on advanced LbL coatings in two related research areas of great interest for the scientific community, namely chemical sensing (pH, gases and volatile organic compounds detection) as well as biological/biochemical sensing (proteins, immunoglobulins, antibodies or DNA detection).
Open Access
Effect of both protective and reducing agents in the synthesis of multicolor silver nanoparticles
(Springer, 2013) Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Urrutia Azcona, Aitor; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, the influence of variable molar ratios between reducing and loading agents (1:100, 1:50, 1:20, 1:10, 1:5, 1:2, 1:1, 2:1) and between protective and loading agents (0.3:1, 0.75:1, 1.5:1, 3:1, 7.5:1, 30:1, 75:1) in the synthesis of silver nanoparticles by chemical reduction has been evaluated to obtain multicolor nanoparticles with a high stability in time. The protective agent poly(acrylic acid, sodium salt) (PAA) and reducing agent dimethylaminoborane (DMAB) play a key role in the formation of the resultant color. Evolution of the optical absorption bands of the silver nanoparticles as a function of PAA and DMAB molar ratios made it possible to confirm the presence of silver nanoparticles or clusters with a specific shape. The results reveal that a wide range of colors (violet, blue, green, brown, yellow, red, orange), sizes (from nanometer to micrometer), and shapes (cubic, rod, triangle, hexagonal, spherical) can be perfectly tuned by means of a fine control of the PAA and DMAB molar concentrations.
Open Access
Optical sensors based on lossy-mode resonances
(Elsevier Science, 2017) Matías Maestro, Ignacio; Ascorbe Muruzabal, Joaquín; Acha Morrás, Nerea de; López Torres, Diego; Zubiate Orzanco, Pablo; Sánchez Zábal, Pedro; Urrutia Azcona, Aitor; Socorro Leránoz, Abián Bentor; Rivero Fuente, Pedro J.; Hernáez Sáenz de Zaitigui, Miguel; Elosúa Aguado, César; Goicoechea Fernández, Javier; Bariáin Aisa, Cándido; Corres Sanz, Jesús María; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC
Open Access
An antibacterial coating based on a polymer/sol-gel hybrid matrix loaded with silver nanoparticles
(Springer, 2011) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this work a novel antibacterial surface composed of an organic-inorganic hybrid matrix of tetraorthosilicate and a polyelectrolyte is presented. A precursor solution of tetraethoxysilane (TEOS) and poly(acrylic acid sodium salt) (PAA) was prepared and subsequently thin films were fabricated by the dip-coating technique using glass slides as substrates. This hybrid matrix coating is further loaded with silver nanoparticles using an in situ synthesis route. The morphology and composition of the coatings have been studied using UV-VIS spectroscopy and atomic force microscopy (AFM). Energy dispersive X-ray (EDX) was also used to confirm the presence of the resulting silver nanoparticles within the thin films. Finally the coatings have been tested in bacterial cultures of genus Lactobacillus plantarum to observe their antibacterial properties. It has been experimentally demonstrated that these silver loaded organic-inorganic hybrid films have a very good antimicrobial behavior against this type of bacteria.