Open Access
Micro and nanostructured materials for the development of optical fibre sensors
(MDPI, 2017) Elosúa Aguado, César; Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Ruiz Zamarreño, Carlos; Corres Sanz, Jesús María; Bariáin Aisa, Cándido; Goicoechea Fernández, Javier; Hernáez Sáenz de Zaitigui, Miguel; Rivero Fuente, Pedro J.; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; Sánchez Zábal, Pedro; Zubiate Orzanco, Pablo; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Ozcariz Celaya, Aritz; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The measurement of chemical and biomedical parameters can take advantage of the features exclusively offered by optical fibre: passive nature, electromagnetic immunity and chemical stability are some of the most relevant ones. The small dimensions of the fibre generally require that the sensing material be loaded into a supporting matrix whose morphology is adjusted at a nanometric scale. Thanks to the advances in nanotechnology new deposition methods have been developed: they allow reagents from different chemical nature to be embedded into films with a thickness always below a few microns that also show a relevant aspect ratio to ensure a high transduction interface. This review reveals some of the main techniques that are currently been employed to develop this kind of sensors, describing in detail both the resulting supporting matrices as well as the sensing materials used. The main objective is to offer a general view of the state of the art to expose the main challenges and chances that this technology is facing currently.
Open Access
Optical fiber sensors based on nanoparticle-embedded coatings
(Hindawi Publishing Corporation, 2015) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The use of nanoparticles (NPs) in scientific applications has attracted the attention of many researchers in the last few years. The use of NPs can help researchers to tune the physical characteristics of the sensing coating (thickness, roughness, specific area, refractive index, etc.) leading to enhanced sensors with response time or sensitivity better than traditional sensing coatings. Additionally, NPs also offer other special properties that depend on their nanometric size, and this is also a source of new sensing applications. This review focuses on the current status of research in the use of NPs within coatings in optical fiber sensing. Most used sensing principles in fiber optics are briefly described and classified into several groups: absorbance-based sensors, interferometric sensors, fluorescence-based sensors, fiber grating sensors, and resonance-based sensors, among others. For each sensor group, specific examples of the utilization of NP-embedded coatings in their sensing structure are reported.
Open Access
Optical fiber sensors based on gold nanorods embedded in polymeric thin films
(Elsevier, 2018) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rivero Fuente, Pedro J.; Pildain Lería, Ander; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
In this work, we present a study about the generation and analysis of optical resonances caused by gold nanorods (GNRs) embedded in films. GNRs were embedded in polymeric thin films using the Layerby-Layer nanoassembly (LbL) deposition technique. Polymer/GNRs thin films of different thicknesses were deposited on the surface of cladding removed optical fibers for sensing. The spectral responses of the optical fiber sensors were monitored during the build-up of the thin films. The generation of two Localized Surface Plasmon Resonances (LSPRs) associated to the GNRs was observed in thinner coatings. These devices with around 12 polymer/GNRs bilayers were characterized as refractometers, providing an intensity-based sensitivity up to 75.69 dB/RIU. For thicker polymer/GNRs overlays, both LSPRs bands were also generated and, additionally, it was observed a new Lossy Mode Resonance (LMR) band due to modes coupled to the sensitive coating. The dependence of these three resonance bands with the surrounding refractive index was studied. Finally, these sensors were tested in a climatic chamber in the 20-90% relative humidity (RH) range and the LMR showed a good sensitivity to RH changes while the LSPR bands remained very stable in comparison. Results showed an excellent sensitivity of 11.2 nm/%RH for the LMR, confirming the potential of this type of optical fiber sensor based on the combination of LSPRs and LMRs bands.
Open Access
Humidity sensor based on a long-period fiber grating coated with a hydrophobic thin film
(2010) Urrutia Azcona, Aitor; Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
In this work it is proposed a novel fiber optic humidity sensor based on a functionally coated long-period fiber grating (LPG). The coating is composed of tetraorthosilicate matrix functionalized with perfluorooctyltriethoxysilane and its fabrication was performed by the sol-gel technique using a dip coating process using the LPG as substrate. This technique allows to fabricate sensitive films in a fast and simple way compared to other overlay fabrication techniques. The fabricated sensor was tested in a programmable temperature and climatic chamber. Relative humidity (RH) was varied in range from 20%RH to 80%RH at room temperature. The results showed a smooth exponential-like wavelength shift of the LPG attenuation band.
Open Access
Electrospun nanofiber mats for evanescent optical fiber sensors
(Elsevier, 2013) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rivero Fuente, Pedro J.; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, a study about the optical response of electrospun nanofiber (ENF) coatings for their use in evanescent optical fiber sensors is presented. Several types of ENF mats composed of poly(acrylic acid) (PAA) were developed with different ENF diameters and densities. These ENF mats were deposited onto an optical fiber core in order to fabricate humidity evanescent optical fiber sensors. The devices were exposed to relative humidity (RH) variations from 30% RH to 95%RH. The transfer functions of the devices (transmitted optical power versus relative humidity) presented two well-differenced behaviors depending on the ENF diameter and the ENF mat density. The devices with lower ENF diameters and higher mat density showed an increase in the transmitted optical power when RH increased. On the contrary, the devices with higher ENF diameters and lower mat density showed a decrease in the transmitted optical power when RH increased. In addition to this, sensors with thinner ENF overlays, showed a higher sensitivity. In order to study the response time of these devices, the ENFs sensors were submitted to human breathing cycles and presented a response time around 340 ms (exhalation). In spite of the high RH conditions of this experiment, the devices showed a recovery time around 210 ms and a negligible hysteresis or drift with respect to the initial condition (inhalation).
Open Access
Simultaneous measurement of humidity and temperature based on a partially coated optical fiber long period grating
(Elsevier, 2016) Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Ricchiuti, Amelia L.; Barrera, D.; Arregui San Martín, Francisco Javier; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
A humidity and temperature optical fiber sensor based on a long-period grating (LPG), which can provide simultaneous response to both magnitudes, is proposed and demonstrated via experiments. Previously, the LPG was fully coated with humidity sensitive nanostructured polymeric thin films by the Layer-by-Layer (LbL) nano assembly technique. Hence the surrounding refractive index was changed, so provoking wavelength shifts of the attenuation bands of the transmission spectrum. This fully coated LPG was exposed to relative humidity (RH) and temperature tests, varying from 20% to 80% RH and from 25 to 85 °C, respectively. Then, half of the LPG coating was chemically removed and this results in the splitting of the main attenuation band into two different contributions. When this semi-coated LPG was also exposed to RH and temperature tests, the new two attenuation bands presented different behaviors for humidity and temperature. This novel dual-wavelength based sensing method enables the simultaneous measurement of RH and temperature using only one LPG.
Open Access
Optical sensors based on lossy-mode resonances
(Elsevier Science, 2017) Matías Maestro, Ignacio; Ascorbe Muruzabal, Joaquín; Acha Morrás, Nerea de; López Torres, Diego; Zubiate Orzanco, Pablo; Sánchez Zábal, Pedro; Urrutia Azcona, Aitor; Socorro Leránoz, Abián Bentor; Rivero Fuente, Pedro J.; Hernáez Sáenz de Zaitigui, Miguel; Elosúa Aguado, César; Goicoechea Fernández, Javier; Bariáin Aisa, Cándido; Corres Sanz, Jesús María; Ruiz Zamarreño, Carlos; Arregui San Martín, Francisco Javier; Del Villar, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC
Open Access
Route towards a label-free optical waveguide sensing platform based on lossy mode resonances
(IFSA Publishing, 2019) Ruiz Zamarreño, Carlos; Zubiate Orzanco, Pablo; Ozcariz Celaya, Aritz; Elosúa Aguado, César; Socorro Leránoz, Abián Bentor; Urrutia Azcona, Aitor; López Torres, Diego; Acha Morrás, Nerea de; Ascorbe Muruzabal, Joaquín; Vitoria Pascual, Ignacio; Imas González, José Javier; Corres Sanz, Jesús María; Díaz Lucas, Silvia; Hernáez Sáenz de Zaitigui, Miguel; Goicoechea Fernández, Javier; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Del Villar, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua,0011-1365-2017- 000117; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA26
According to recent market studies of the North American company Allied Market Research, the field of photonic sensors is an emerging strategic field for the following years and it is expected to garner $18 billion by 2021. The integration of micro and nanofabrication technologies in the field of sensors has allowed the development of new technological concepts such as lab-on-a-chip which have achieved extraordinary advances in terms of detection and applicability, for example in the field of biosensors. This continuous development has allowed that equipment consisting of many complex devices that occupied a whole room a few years ago, at present it is possible to handle them in the palm of the hand; that formerly long duration processes are carried out in a matter of milliseconds and that a technology previously dedicated solely to military or scientific uses is available to the vast majority of consumers. The adequate combination of micro and nanostructured coatings with optical fiber sensors has permitted us to develop novel sensing technologies, such as the first experimental demonstration of lossy mode resonances (LMRs) for sensing applications, with more than one hundred citations and related publications in high rank journals and top conferences. In fact, fiber optic LMR-based devices have been proven as devices with one of the highest sensitivity for refractometric applications. Refractive index sensitivity is an indirect and simple indicator of how sensitive the device is to chemical and biological species, topic where this proposal is focused. Consequently, the utilization of these devices for chemical and biosensing applications is a clear opportunity that could open novel and interesting research lines and applications as well as simplify current analytical methodologies. As a result, on the basis of our previous experience with LMR based sensors to attain very high sensitivities, the objective of this paper is presenting the route for the development of label-free optical waveguide sensing platform based on LMRs that enable to explore the limits of this technology for bio-chemosensing applications.
Open Access
An antibacterial submicron fiber mat with in situ synthesized silver nanoparticles
(Wiley, 2012) Rivero Fuente, Pedro J.; Urrutia Azcona, Aitor; Goicoechea Fernández, Javier; Rodríguez, Yoany; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
This work presents an alternative approachfor fabricating electrospun submicron highly hydrophilicfiber mats loaded with silver nanoparticles. These fiber matsshow a high efficient antibacterial behavior, very attractivefor applications like wound healing and skin regenerationprocesses. The fabrication method is divided in two steps.First, poly(acrylic acid) (PAA) and b-cyclodextrin (b-CD)submicron fibers were electrospun and further stabilizedusing a thermal treatment, yielding stable hydrogel-likefibers with diameters ranging from 100 nm up to severalmicrons. In the second step, silver ions were loaded into thefibers and then reduced to silver nanoparticles in-situ. Theelectrospinning parameters were adjusted to achieve thedesired properties of the fiber mat (density, size) and after-wards, the characteristics of the silver nanoparticles(amount, size, aggregation) were tuned by controlling thesilver ion loading mechanism. Highly biocide surfaces wereachieved showing more than 99.99% of killing efficiency.The two-step process improves the reproducibility and tun-ability of the fiber mats. To our knowledge, this is the firsttime that stable hydrogel fibers with a highly biocide behav-ior have been fabricated using electrospinning.
Open Access
Multicolor layer-by-layer films using weak polyelectrolyte assisted synthesis of silver nanoparticles
(Springer, 2013) Rivero Fuente, Pedro J.; Goicoechea Fernández, Javier; Urrutia Azcona, Aitor; Matías Maestro, Ignacio; Arregui San Martín, Francisco Javier; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In the present study, we show that silver nanoparticles (AgNPs) with different shape, aggregation state and color (violet, green, orange) have been successfully incorporated into polyelectrolyte multilayer thin films using the layerby- layer (LbL) assembly. In order to obtain colored thin films based on AgNPs is necessary to maintain the aggregation state of the nanoparticles, a non-trivial aspect in which this work is focused on. The use of Poly(acrylic acid, sodium salt) (PAA) as a protective agent of the AgNPs is the key element to preserve the aggregation state and makes possible the presence of similar aggregates (shape and size) within the LbLcolored films. This approach based on electrostatic interactions of the polymeric chains and the immobilization of AgNPs with different shape and size into the thin films opens up a new interesting perspective to fabricate multicolornanocomposites based on AgNPs.