Person:
Algueta-Miguel, Jose M.

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/48494

Last Name

Algueta-Miguel

First Name

Jose M.

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

ORCID

0000-0001-9323-4516

person.page.upna

8574

Full item page

Search Results

Now showing 1 - 10 of 14

Open Access
Energy-efficient amplifiers based on quasi-floating gate techniques
(MDPI, 2021) López Martín, Antonio; Garde Luque, María Pilar; Algueta-Miguel, Jose M.; Beloso Legarra, Javier; González Carvajal, Ramón; Ramírez-Angulo, Jaime; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Energy efficiency is a key requirement in the design of amplifiers for modern wireless applications. The use of quasi-floating gate (QFG) transistors is a very convenient approach to achieve such energy efficiency. We illustrate different QFG circuit design techniques aimed to implement low-voltage energy-efficient class AB amplifiers. A new super class AB QFG amplifier is presented as a design example including some of the techniques described. The amplifier has been fabricated in a 130 nm CMOS test chip prototype. Measurement results confirm that low-voltage ultra low power amplifiers can be designed preserving at the same time excellent small-signal and large-signal performance.
Open Access
Subsampling OFDM-based ultrasonic data communication through metallic channels for monitoring of cargo containers
(IEEE, 2019) García Oya, José Ramón; Algueta-Miguel, Jose M.; García Doblado, José; Muñoz Chavero, Fernando; Hidalgo Fort, Eduardo; Baena Lecuyer, Vicente; López Martín, Antonio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
An enhanced ultrasonic communication system based on piezoelectric transducers for monitoring of goods in cargo containers is presented. The proposed system consists of several sensors placed inside the container, whose data are collected and transmitted outside it. Data transmission is carried out by an ultrasonic communication channel, in order to avoid drilling the wall of the container. The proposed data communication system is based on the transmission of a 128-OFDM signal. This modulation has been chosen due to its robustness to channels with frequency-selective fading and its spectrum efficiency. In order to increase the signal bandwidth and to reduce the power consumption at the internal node (transmitter), the proposed system exploits the non-linearity of the metallic channel to transmit at higher resonance frequencies. Moreover, power consumption at the external node (receiver) is reduced by using a subsampling based receiver, which allows its implementation by low-cost electronics.
Open Access
Magnetic binary encoding system based on 3D printing and GMI detection prototype
(Elsevier, 2022) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; López Ortega, Alberto; Garayo Urabayen, Eneko; Gómez Polo, Cristina; Aresti Bartolomé, Maite; Soria Picón, Eneko; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Gobierno de Navarra / Nafarroako Gobernua; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, the feasibility of a magnetic binary encoding system using 3D printing technology is analyzed. The study has a double interest, that is, the possibility of printing a 3D piece that contains the codified information and the development of a system for its decoding. For this purpose, magnetic nanoparticles (magnetite Fe3O4) were embedded in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL). Similar to a conventional barcode, a rectangular piece with an alternating pattern of strips with absence (only polymer) and a 5 wt% of embedded magnetic nanoparticles was 3D printed employing the Fused Deposition Modelling tech- nique (FDM). The information was decoded by means of a Giant Magnetoimpedance (GMI) sensor-based pro- totype, by scanning the surface of the piece and measuring the changes in the magnetic field. As sensor nucleus, an amorphous soft magnetic wire of nominal composition (Co0.94 Fe0.06)72.5 Si12.5 B15 was employed. The decoding prototype incorporates a homemade electronic sensor interface that permits, at the time, the GMI sensor excitation and the subsequent signal conditioning to optimize its response. The output signal enables the detection of the magnetite nanoparticles and the magnetic decoding of the encoded information (“1” and “0”, presence or absence of the magnetic nanoparticles, respectively).
Open Access
Enhanced single-stage folded cascode OTA suitable for large capacitive loads
(IEEE, 2018) López Martín, Antonio; Garde Luque, María Pilar; Algueta-Miguel, Jose M.; Cruz Blas, Carlos Aristóteles de la; Carvajal, Ramón G.; Ramírez-Angulo, Jaime; Institute of Smart Cities - ISC
An enhanced single-stage folded cascode operational transconductance amplifier able to drive large capacitive loads is presented. Circuits that adaptively bias the input differential pair and the current folding stage are employed, which provide class AB operation with dynamic current boosting and increased gainbandwidth (GBW) product. Measurement results of a test chip prototype fabricated in a 0.5-µm CMOS process show an increase in slew rate and GBW by a factor of 30 and 15, respectively, versus the class A version using the same supply voltage and bias currents. Overhead in other performance metrics is small.
Open Access
Low-power ultrasonic front-end for cargo container monitoring
(IEEE, 2019) Algueta-Miguel, Jose M.; García Oya, José Ramón; López Martín, Antonio; Cruz Blas, Carlos Aristóteles de la; Muñoz Chavero, Fernando; Hidalgo Fort, Eduardo; Institute of Smart Cities - ISC
A low-power ultrasonic communication system conceived for cargo container monitoring is presented. Two piezoelectric transducers operating at 40 kHz are used for generating and acquiring an ultrasonic signal through the metallic wall, thus establishing a non-invasive inside-outside communication that preserves the container integrity. Both transducers are fixed by means of a novel magnetic case designed for optimizing data transmission. The acoustic and electrical characteristics of the ultrasonic channel are analyzed. An experimental measurement setup based on FPGA has been implemented for comparing some basic modulation and detection schemes in terms of Bit Error Rate (BER), also considering their robustness against undesired mechanical and electromagnetic perturbations. On this basis, a compact digital DBPSK modulator using a square carrier signal is proposed. Frequency and amplitude tracking algorithms are designed for optimizing the quality and robustness of the data transmission. Finally, a low-power low-rate (up to few kbps) architecture based on the previous elements is presented. All the proposed contributions are experimentally validated.
Open Access
Analog lock-in amplifier design using subsampling for accuracy enhancement in GMI sensor applications
(MDPI, 2023) Algueta-Miguel, Jose M.; Beato López, Juan Jesús; López Martín, Antonio; Ciencias; Zientziak; Institute of Smart Cities - ISC; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA2005
A frequency downscaling technique for enhancing the accuracy of analog lock-in amplifier (LIA) architectures in giant magneto-impedance (GMI) sensor applications is presented in this paper. As a proof of concept, the proposed method is applied to two different LIA topologies using, respectively, analog and switching-based multiplication for phase-sensitive detection. Specifically, the operation frequency of both the input and the reference signals of the phase-sensitive detector (PSD) block of the LIA is reduced through a subsampling process using sample-and-hold (SH) circuits. A frequency downscaling from 200 kHz, which is the optimal operating frequency of the employed GMI sensor, to 1 kHz has been performed. In this way, the proposed technique exploits the inherent advantages of analog signal multiplication at low frequencies, while the principle of operation of the PSD remains unaltered. The circuits were assembled using discrete components, and the frequency downscaling proposal was experimentally validated by comparing the measurement accuracy with the equivalent conventional circuits. The experimental results revealed that the error in the signal magnitude measurements was reduced by a factor of 8 in the case of the analog multipliers and by a factor of 21 when a PSD based on switched multipliers was used. The error in-phase detection using a two-phase LIA was also reduced by more than 25%.
Open Access
Energy harvesting approaches in IoT scenarios with very low ambient energy
(European Association for the Development of Renewable Energy, Environment and Power Quality (EA4EPQ), 2019) López Martín, Antonio; Algueta-Miguel, Jose M.; Matías Maestro, Ignacio; Institute of Smart Cities - ISC
The feasibility of multi-source energy harvesting in Internet of Things (IoT) scenarios with low and intermittent ambient energy is addressed. As a relevant case study, application to a smart cargo container system is analysed. The most relevant features of the main energy sources available in this target application are identified, and various transducers adapted to such sources are evaluated. Measurement results indicate that combined piezoelectric and thermoelectric generation inside cargo containers can significantly extend the battery lifetime of IoT end nodes embedded in such containers.
Open Access
Class AB amplifier with enhanced slew rate and GBW
(John Wiley & Sons, 2019) Garde Luque, María Pilar; López Martín, Antonio; Algueta-Miguel, Jose M.; Ramírez-Angulo, Jaime; González Carvajal, Ramón; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
The design of a micropower class AB operational transconductance amplifier with large dynamic current to quiescent current ratio is addressed. It is based on a compact and power-efficient adaptive biasing circuit and a class AB current follower using the Quasi-Floating Gate (QFG) technique. The amplifier has been designed and fabricated in a 0.5 um CMOS process. Simulation and measurement results show a slew rate (SR) improvement factor versus the class A version larger than 4 for the same supply voltage and bias currents, as well as enhanced small-signal performance.
Open Access
1-V 15-μW 130-nm CMOS super class AB OTA
(IEEE, 2020) López Martín, Antonio; Algueta-Miguel, Jose M.; Garde Luque, María Pilar; Carvajal, Ramón G.; Ramírez-Angulo, Jaime; Institute of Smart Cities - ISC
A super class AB recycling folded cascode amplifier in 130 nm CMOS is presented. It combines for the first time adaptive biasing of the differential input pair, nonlinear current mirrors with current starving and dynamic biasing of the cascode transistors in the output branch. Measurements using a ±0.5V supply show slew rate and gain bandwidth product improvement factors of 26 and 112 versus the conventional topology for the same bias currents, yielding the highest combined FoM to date.
Open Access
Non-linear GMI decoding in 3D printed magnetic encoded systems
(Elsevier, 2023) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; Garayo Urabayen, Eneko; López Ortega, Alberto; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The nonlinear giant magnetoimpedance (GMI) effect was explored as a highly sensitive sensing technology in 3D-printed magnetic encoded systems. Magnetic nanoparticles with low (magnetite, Fe3O4) and high (Co ferrite, Co0.7Fe2.3O4) magnetic remanence were embedded (10 wt%) in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL) and extruded in magnetic filaments to be 3D printed by the Fused Deposition Modelling technique (FDM). Two different geometries were constructed namely, individual magnetic strips and fixed barcoded pieces. The stray magnetic fields generated by the magnetic nanoparticles were detected through the non-linear (second harmonic) GMI voltage using a soft magnetic CoFeSiB wire as the nucleus sensor. The decoding response was analyzed as a function of the magnetization remanence of the nanoparticles, the distance between the individual magnetic strips, and the position (height) of the GMI decoding sensor. It has been shown that modification of the net magnetization direction of each individual fixed strip within the barcode geometry is possible through the application of local external magnetic fields. This possibility improves the versatility of the 3D binary encoding system by adding an additional state (0 without nanoparticles, 1 or −1 depending on the relative orientation of the net magnetization along the strips) during the codifying procedure.