Person:
Ederra Urzainqui, Íñigo

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/48935

Last Name

Ederra Urzainqui

First Name

Íñigo

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

person.page.instituteName

ISC. Institute of Smart Cities

ORCID

0000-0002-0497-1627

person.page.upna

2699

Full item page

Search Results

Now showing 1 - 10 of 23

Open Access
Design of 300 ghz combined doubler/subharmonic mixer based on schottky diodes with integrated mmic based local oscillator
(MDPI, 2020) Pérez Escudero, José Manuel; Quemada Mayoral, Carlos; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this paper the design and experimental characterization of a combined doublersubharmonic mixer based on Schottky diodes which uses a 75 GHz MMIC based local oscillator is presented. This solution integrates in the same substrate the doubler and the mixer, which share the same metallic packaging with the local oscillator. The prototype has been fabricated and measured. For characterization, the Y-Factor technique has been used and the prototype yields a best conversion loss and equivalent noise temperature of 11 dB and 1976 K, respectively, at 305 GHz. This performance is close to the state of the art, and shows the potential of this approach, which allows a significant reduction in terms of size and volume.
Open Access
Moisture content estimation models of flour matrices in the 67-110 GHz frequency range using a nondestructive and contactless monitoring system
(IEEE, 2023) Quemada Mayoral, Carlos; Ederra Urzainqui, Íñigo; Beruete Díaz, Miguel; Gonzalo García, Ramón; Iriarte Galarregui, Juan Carlos; Estadística, Informática y Matemáticas; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Estatistika, Informatika eta Matematika; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This work addresses the lack of moisture content estimation models for food products in the millimeter-wave frequency range and showcases the potential of this range for designing compact, cost-effective, and in-line food moisture sensors. The moisture content estimation models developed in this study are intended for flour-based mixtures in the 67-110 GHz frequency range and are derived by means of a nondestructive and contactless monitoring system. To this aim, data obtained by continuous-wave (CW) vector network analyzer (VNA) spectroscopy is used to create two different models, both with a coefficient of determination ( R2 ) of 0.97. One model is based on the theoretical response obtained by means of the Looyenga effective medium theory (EMT) model, while the other is based on measured data. Both models have been experimentally validated with root mean square error (RMSE) values of 0.4% and 0.35%, respectively. These small estimation errors show the potential of this frequency range to design compact, cost-effective, and in-line food moisture sensors. This research contributes to improving quality control and monitoring of moisture levels in flour-based mixtures.
Open Access
Compact bull's-eye antenna in ridge gap waveguide with circular polarization at 60 GHz
(IEEE, 2021) Pérez Quintana, Dayan; Ederra Urzainqui, Íñigo; Beruete Díaz, Miguel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, a Bull's-Eye (BE) antenna with circular polarization (CP) based on ridge gap waveguide (RGW) technology, working in the millimeter-wave band (60 GHz) is numerically and experimentally demonstrated. The structure is coupled through a step transition to a ridge-line that ends in two orthogonal arms of different lengths to generate CP. The wave is coupled to the top plate by a central diamond slot surrounded by the BE structure, which consists of four concentric periodic corrugations around the slot. Simulations and experimental results are in good agreement, with practical bandwidth of 6.8% with respect to center frequency and peak gain of 18.4 dB. The antenna has right-handed CP (RHCP) with polarization discrimination of more than 30 dB.
Open Access
Remote sensing for plant water content monitoring: a review
(MDPI, 2021) Quemada Mayoral, Carlos; Pérez Escudero, José Manuel; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Santesteban García, Gonzaga; Torres Molina, Nazareth; Iriarte Galarregui, Juan Carlos; Institute of Smart Cities - ISC; Institute for Multidisciplinary Research in Applied Biology - IMAB
Las redes sociales se han convertido en una de las principales fuentes de información, especialmente entre los más jóvenes. Al mismo tiempo, se ha incrementado la producción y circulación de información falsa o fake news a través de las redes. En este contexto, resulta crucial que los jóvenes adquieran estrategias y competencias para realizar una lectura crítica de la información que consumen. Este estudio busca analizar el comportamiento del alumnado de secundaria ante la información falsa y el efecto de una intervención didáctica, realizada online durante la pandemia de la covid-19, cuyo objetivo era que el alumnado desarrollara competencias para detectar noticias falsas. Se trata de una investigación participativa con un diseño de pre-test y post-test. Los resultados muestran que el alumnado incrementó su competencia para identificar algunos tipos de falsedad como la información no probada y la información tergiversada, si bien tuvo problemas para reconocer información descontextualizada o el uso de lenguaje discriminatorio. Las estrategias que más utilizó son la comprobación de datos en internet y el uso de verificadores. Se observaron comportamientos diferenciados entre el alumnado que identificó la información falsa y el que no lo hizo. Las conclusiones apuntan a la necesidad de trabajar en el aula de forma integral, extensiva y transversal la evaluación de la información partiendo de las habilidades que el alumnado ya posee.
Open Access
Hyperbolic lens antenna in groove gap waveguide technology at sub-millimeter waves
(IEEE, 2022) Pérez Quintana, Dayan; Biurrun Quel, Carlos; Ederra Urzainqui, Íñigo; González-Ovejero, David; Beruete Díaz, Miguel; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a flat hyperbolic lens antenna using Groove Gap Waveguide (GGW) technology is designed at 300 GHz. A GGW horn antenna is used to feed the metamaterial lens placed in a parallel plate waveguide (PPW), in order to increase the directivity in the direction of propagation. The combination of both devices, the metalens and the GGW antenna, achieves excellent radiation performance.
Open Access
A gap waveguide-based compact rectangular waveguide to a packaged microstrip inline transition
(MDPI, 2020) Pérez Escudero, José Manuel; Torres García, Alicia E.; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Institute of Smart Cities - ISC
In this paper two different simple to design and easy to manufacturing transitions from a microstrip to rectangular waveguide based on ridge and groove gap waveguides are studied. The first one is based on a combination of a groove and ridge gap waveguide. In this case, the microstrip substrate occupies the whole bottom metallic housing block, namely, the transition and the gap between the bed of nails and the lid; therefore, it does not require any substrate shaping. Nevertheless, the transition needs to replace groove waveguide by ridge gap waveguide sections to avoid higher-order mode excitation. In the second approach, based on only a groove gap waveguide, the substrate is shaped to be only in the microstrip section, that is, outside the bed of nails area. This leads to a simplification of the design procedure. Prototypes of both transitions have been characterized, showing good agreement with the simulations taking into account the manufacturing tolerances. Performance comparable to the state-of-the-art in this frequency band has been achieved.
Open Access
Silicon integrated subharmonic mixer on a photonic-crystal platform
(IEEE, 2021) Torres García, Alicia E.; Pérez Escudero, José Manuel; Teniente Vallinas, Jorge; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photoniccrystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a simple, easy to integrate, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the stateof-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds.
Open Access
Modified Soret lenses for dual band integrated detectors at submillimetre and millimetre wavelengths
(IEEE, 2020) Torres García, Alicia E.; Pérez Escudero, José Manuel; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photonic crystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a simple, easy to integrate, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the state of-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds.
Open Access
Design of a slotted Substrate Integrated waveguide antenna using a metasurface
(IEEE, 2021) Chocarro Álvarez, Javier; Pérez Escudero, José Manuel; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this paper, the use of a metasurface to improve the radiation properties of a Substrate Integrated Waveguide based slotted antenna is proposed. The design process of a metasurface covered 8 element slot antenna array following a Chebyshev distribution is presented and its performance is compared with that of a conventional one. The results demonstrate the improvement in the radiation performance that can be achieved, without affecting the bandwidth.
Open Access
Fully metallic Luneburg metalens antenna in gap waveguide technology at V-band
(IEEE, 2023) Pérez Quintana, Dayan; Bilitos, Christos; Ruiz-García, Jorge; Ederra Urzainqui, Íñigo; Teniente Vallinas, Jorge; González-Ovejero, David; Beruete Díaz, Miguel; Institute of Smart Cities - ISC
This article presents the design of a flat Luneburg metalens antenna at V-band using gap waveguide (GW) technology. The metalens consists of a parallel plate waveguide (PPW) loaded with metallic pins whose height is modulated to get an effective refractive index that follows the Luneburg equation. A Groove GW (GGW) H-plane horn is used to illuminate the metalens, such that the rays are collimated and a planar wavefront is generated in the direction of propagation. Since the structure at hand is planar, it can be efficiently integrated on flat surfaces. Moreover, the fully metallic structure is mechanically robust and presents lower losses than lenses including dielectric substrates. A prototype has been fabricated and tested, simulations and experimental results are in very good agreement. The metalens yields an input reflection coefficient (S11) below −10 dB from 45 to 70 GHz, whereas the −3 dB gain fractional bandwidth is 26.2% with respect to a center frequency of 60 GHz, with a peak of 22.5 dB at 61 GHz. These features make this design an interesting solution for millimeter-wave (MMW) applications.