Person:
Ederra Urzainqui, Íñigo

Profile Picture

Email Address

person.page.identifierURI

https://academica-e.unavarra.es/handle/2454/48935

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Ederra Urzainqui

First Name

Íñigo

person.page.departamento

Ingeniería Eléctrica, Electrónica y de Comunicación

person.page.instituteName

ISC. Institute of Smart Cities

ORCID

0000-0002-0497-1627

person.page.upna

2699

Name

Filters

2018 - 20193
Reset filters

Settings

Start date: 2010 × End date: 2019 × Subject: Microstrip ×

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    PublicationOpen Access
    Design of a groove gap waveguide to microstrip inline transition
    (IEEE, 2019) Pérez Escudero, José Manuel; Torres García, Alicia E.; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    In this paper the design of an inline transition between microstrip and groove gap waveguide operating at Wband is presented. The transition consists of two sections: a tapered microstrip line and a Chebyshev transformer. The simplicity of this design makes this transition appropriate for MMIC packaging at millimeter frequencies and above. Experimental validation has been carried out in theW-band. Good performance has been achieved: return loss better than 10 dB and mean insertion loss lower than 2 dB.
  • Thumbnail Image
    PublicationOpen Access
    A simplified design inline microstrip-to-waveguide transition
    (MDPI, 2018) Ederra Urzainqui, Íñigo; Gonzalo García, Ramón; Pérez Escudero, José Manuel; Torres García, Alicia E.; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    A simplified design of an inline transition between microstrip and rectangular waveguide is presented in this paper. The transition makes use of a dielectric filled rectangular waveguide (DFRW) as an intermediate step, which simplifies manufacturing and allows for an analytical design. The behavior of the transition has been experimentally validated in the W-band by means of a back-to-back configuration. Good performance has been achieved: a return loss greaterthan 10 dB and mean insertion loss lower than 1 dB.
  • Thumbnail Image
    PublicationOpen Access
    A Chebyshev transformer-based microstri-to-groove-gap-waveguide inline transition for MMIC packaging
    (IEEE, 2019) Pérez Escudero, José Manuel; Torres García, Alicia E.; Gonzalo García, Ramón; Ederra Urzainqui, Íñigo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
    The gap waveguide technology has become an alternative to millimeter- and submillimeter-wave electronic circuit packaging thanks to the loss reduction associated with its use. In this paper, a simplified design of an inline transition between a microstrip and a groove gap waveguide (GGW) operating at the W-band is presented. The transition consists of a tapered microstrip line and a Chebyshev adapter that couple the quasi-TEM mode of the microstrip line to the so-called vertical mode of the GGW. The simplicity of this design makes this transition appropriate for monolithic microwave integrated circuit (MMIC) packaging at millimeter frequencies and above. The simulation results have been experimentally validated in the W-band. A good performance has been achieved, resulting in a return loss better than 10 dB and a mean insertion loss lower than 2 dB.