Person:
Iribas Pardo, Haritz

Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Iribas Pardo

First Name

Haritz

person.page.departamento

Estadística, Informática y Matemáticas

ORCID

0000-0003-4260-2379

person.page.upna

810714

Name

Filters

2017 - 20182
Reset filters

Settings

Author: Mariñelarena Ollacarizqueta, Jon × Subject: BODTA sensors ×

Search Results

Now showing 1 - 2 of 2
  • Thumbnail Image
    PublicationOpen Access
    Effects of pump pulse extinction ratio in Brillouin optical time-domain analysis sensors
    (Optical Society of America, 2017) Iribas Pardo, Haritz; Mariñelarena Ollacarizqueta, Jon; Feng, Cheng; Urricelqui Polvorinos, Javier; Schneider, Thomas; Loayssa Lara, Alayn; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    We report on two previously unknown non-local effects that have been found to impair Brillouin optical time-domain analysis (BOTDA) sensors that deploy limited extinction ratio (ER) pump pulses. The first one originates in the increased depletion of the pedestal of the pump pulses by the amplified probe wave, which in turn entails a reduced amplification of the probe and a measurement distortion. The second effect is due to the interplay between the transient response of the erbium-doped fiber amplifiers (EDFA) that are normally deployed to amplify the pump and the pedestal of the pump pulses. The EDFA amplification modifies the pedestal that follows the pulses in such a way that it also leads to a distortion of the measured gain spectra after normalization. Both effects are shown to lead to non-local effects in the measurements that have similar characteristics to those induced by pump pulse depletion. In fact, the total depletion factor for calculations of the Brillouin frequency shift (BFS) error in BOTDA sensors is shown to be the addition of the depletion factors linked to the pump pulse as well as the pedestal. A theoretical model is developed to analyze both effects by numerical simulation. Furthermore, the effects are investigated experimentally in long-range BOTDA sensors. The pedestal depletion effect is shown to severely constrain the probe power as well as the minimum ER of the pulses that can be deployed in BOTDA sensors. For instance, it is shown that, in a long-range dual-probe BOTDA, an ER higher that 32-dB, which is above that provided by standard electro-optic modulators (EOM), is necessary to be able to deploy a probe power of -3 dBm, which is the theoretical limit for that type of sensors. Even more severe can be the limitation due to the depletion effect induced by the EDFA transient response. It is found that the impairments brought by this effect are independent of the probe power, hence setting an ultimate limit for the BOTDA sensor performance. Experimentally, a long-range BOTDA deploying a 26-dB ER EOM and a conventional EDFA is shown to exhibit a BFS error higher than 1 MHz even for very small probe power.
  • Thumbnail Image
    PublicationOpen Access
    Fiber-optic brillouin distributed sensors: from dynamic to long-range measurements
    (CRC Press, 2018) Loayssa Lara, Alayn; Urricelqui Polvorinos, Javier; Iribas Pardo, Haritz; Mompó Roselló, Juan José; Mariñelarena Ollacarizqueta, Jon; Estadística, Informática y Matemáticas; Ingeniería Eléctrica, Electrónica y de Comunicación; Estatistika, Informatika eta Matematika; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
    This chapter focuses on Brillouin optical time-domain analysis (BOTDA) sensors because they are the most successful Brillouin distributed sensors (BDS) type in terms of performance and practical applications. Distributed sensor featuring can be done in the time, coherence, or frequency domains, giving rise to the three main analysis BDS types: BOTDA, Brillouin optical correlation-domain analysis (BOCDA), and Brillouin optical frequency-domain analysis (BOFDA). The distance range of measurements performed using a BOTDA sensor is given by the length of sensing fiber that the system is able to measure with a specified performance in terms of measurement precision and time. The chapter reviews the fundamentals and the research directions in BDSs. The applications of the technology are multiple and in diverse fields¿for instance, in the oil and gas industry, where BDSs have been applied to measure temperature and strain along the umbilical cables used for subsea wells.