Person:
Urroz Unzueta, José Carlos

Loading...
Profile Picture

Email Address

Birth Date

Research Projects

Organizational Units

Job Title

Last Name

Urroz Unzueta

First Name

José Carlos

person.page.departamento

Ingeniería

person.page.instituteName

ORCID

0000-0001-8432-3242

person.page.upna

1730

Name

Search Results

Now showing 1 - 3 of 3
  • PublicationOpen Access
    Gaseous fueling of an adapted commercial automotive spark-ignition engine: simplified thermodynamic modeling and experimental study running on hydrogen, methane, carbon monoxide and their mixtures
    (Elsevier, 2023) Urroz Unzueta, José Carlos; Diéguez Elizondo, Pedro; Arzamendi Manterola, María Cruz; Arana Burgui, Miguel; Gandía Pascual, Luis; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Zientziak; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    In the present work, methane, carbon monoxide, hydrogen and the binary mixtures 20 % CH4–80 % H2, 80 % CH4–20 % H2, 25 % CO–75 % H2 (by volume) were considered as fuels of a naturally aspirated port-fuel injection four-cylinder Volkswagen 1.4 L spark-ignition (SI) engine. The interest in these fuels lies in the fact that they can be obtained from renewable resources such as the fermentation or gasification of residual biomasses as well as the electrolysis of water with electricity of renewable origin in the case of hydrogen. In addition, they can be used upon relatively easy modifications of the engines, including the retrofitting of existing internal combustion engines. It has been found that the engine gives similar performance regardless the gaseous fuel nature if the air–fuel equivalence ratio (λ) is the same. Maximum brake torque and mean effective pressure values within 45–89 N⋅m and 4.0–8.0 bar, respectively, have been obtained at values of λ between 1 and 2 at full load, engine speed of 2000 rpm and optimum spark-advance. In contrast, the nature of the gaseous fuel had great influence upon the range of λ values at which a fuel (either pure or blend) could be used. Methane and methane-rich mixtures with hydrogen or carbon monoxide allowed operating the engine at close to stoichiometric conditions (i.e. 1 < λ < 1.5) yielding the highest brake torque and mean effective pressure values. On the contrary, hydrogen and hydrogen-rich mixtures with methane or carbon monoxide could be employed only in the very fuel-lean region (i.e. 1.5 < λ < 2). The behavior of carbon monoxide was intermediate between that of methane and hydrogen. The present study extends and complements previous works in which the aforementioned fuels were compared only under stoichiometric conditions in air (λ = 1). In addition, a simple zero-dimensional thermodynamic combustion model has been developed that allows describing qualitatively the trends set by the several fuels. Although the model is useful to understand the influence of the fuels properties on the engine performance, its predictive capability is limited by the simplifications made.
  • PublicationOpen Access
    Acoustic and psychoacoustic levels from an internal combustion engine fueled by hydrogen vs. gasoline
    (Elsevier, 2022) Arana Burgui, Miguel; San Martín Murugarren, Ricardo; Urroz Unzueta, José Carlos; Diéguez Elizondo, Pedro; Gandía Pascual, Luis; Zientziak; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Ingeniería; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
    Whereas noise generated by road traffic is an important factor in urban pollution, little attention has been paid to this issue in the field of hydrogen-fueled vehicles. The objective of this study is to analyze the influence of the type of fuel (gasoline or hydrogen) on the sound levels produced by a vehicle with an internal combustion engine. A Volkswagen Polo 1.4 vehicle adapted for its bi-fuel hydrogen-gasoline operation has been used. Tests were carried out with the vehicle when stationary to eliminate rolling and aerodynamic noise. Acoustics and psychoacoustics levels were measured both inside and outside the vehicle. A slight increase in the noise level has only been found outside when using hydrogen as fuel, compared to gasoline. The increase is statistically significant, can be quantified between 1.1 and 1.7 dBA and is mainly due to an intensification of the 500 Hz band. Loudness is also higher outside the vehicle (between 2 and 4 sones) when the fuel is hydrogen. Differences in sharpness and roughness values are lower than the just-noticeable difference (JND) values of the parameters. Higher noise levels produced by hydrogen can be attributed to its higher reactivity compared to gasoline.
  • PublicationOpen Access
    Characterization of combustion anomalies in a hydrogen-fueled 1.4 L commercial spark-ignition engine by means of in-cylinder pressure, block-engine vibration, and acoustic measurements
    (Elsevier, 2018) Diéguez Elizondo, Pedro; Urroz Unzueta, José Carlos; Sáinz Casas, David; Machin, J.; Arana Burgui, Miguel; Gandía Pascual, Luis; Institute for Advanced Materials and Mathematics - INAMAT2
    Abnormal combustion phenomena are among the main hurdles for the introduction of hydrogen in the transportation sector through the use of internal combustion engines (ICEs). For that reason the challenge is to guarantee operation free from combustion anomalies at conditions close to the ones giving the best engine output (maximum brake torque and power). To this end, an early and accurate detection of abnormal combustion events is decisive in order to allow the electronic control unit deciding suitable correcting actions. In this work, an automotive size 4-cylinder 1.4 L naturally aspirated port-fuel injection spark ignition Volkswagen engine adapted to run on hydrogen has been investigated. Three distinct methods (in-cylinder pressure, block-engine vibration and acoustic measurements) have been employed to detect abnormal combustion phenomena provoked through the enrichment of the hydrogen-air mixture fed to the cylinders under a wide range of engine speeds (1000–5000 rpm). It has been found that the high-frequency components of the in-cylinder pressure and block engine acceleration signals obtained after a Fourier transform analysis can be used for very sensitive detection of knocking combustion cycles. In the case of the ambient noise measurements, a spectral analysis in terms of third octave bands of the signal recorded by a microphone allowed an accurate characterization. Combustion anomalies could be detected through more intense octave bands at frequencies between 250 Hz and 4 kHz in the case of backfire and between 8 kHz and 20 kHz for knock. Computational fluid dynamics simulations performed indicated that some characteristics of the engine used such as the cylinder valves dimensions and the hydrogen flow rate delivered by the injectors play important roles conditioning the likelihood of suffering backfire events.