Person:
Luis Pérez, Carmelo

Last Name

Luis Pérez

First Name

Carmelo

person.page.departamento

Ingeniería

ORCID

0000-0002-1363-1667

person.page.upna

2277

Full item page

Search Results

Now showing 1 - 10 of 21

Open Access
Development of nanostructured AA3103 by equal channel angular pressing and thermal treatments
(Hindawi, 2014) Luis Pérez, Carmelo; Luri Irigoyen, Rodrigo; León Iriarte, Javier; Puertas Arbizu, Ignacio; Salcedo Pérez, Daniel; Pérez Ruiz, Iván; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza; Gobierno de Navarra / Nafarroako Gobernua, Project EUROINNOVA NANOCONS-IIM10784.RI1
This work presents a study related to the achievement of a nanometric structure in AA3103, employing severe plastic deformation processes (SPD), in this case equal channel angular pressing (ECAP). The changes in the mechanical properties and in the microstructure of AA3103 were studied after being processed by ECAP. Subsequently, scanning electron microscopy was used to determine the evolution of the microstructure after different thermal treatments on the material processed by this severe plastic deformation process. Furthermore, a more profound knowledge of the changes in the mechanical properties of this aluminium alloy was obtained. It was demonstrated that with different appropriate combinations of thermal treatments and ECAP processing, it is possible to significantly improve the mechanical properties through obtaining submicrometric grain size structures.
Open Access
A proposal of a constitutive description for aluminium alloys in both cold and hot working
(MDPI, 2016) León Iriarte, Javier; Luis Pérez, Carmelo; Fuertes Bonel, Juan Pablo; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Salcedo Pérez, Daniel; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
The most important difficulties when the behaviour of a part that is subjected to external mechanical forces is simulated deal with the determination of both the material thermo-mechanical properties and its boundary conditions. The accuracy of the results obtained from the simulation is directly related to the knowledge of the flow stress curve. Therefore, the determination of a material flow rule which is valid for both a wide temperature range and different initial deformation conditions in the starting material presents a great deal of interest when simulation results close to the experimental values are required to be obtained. In this present study, a novel flow stress curve is proposed that is able to accurately predict the behaviour of both materials with no previous accumulated strain and materials that have been previously subjected to severe plastic deformation processes. Moreover, it is possible to use it both for hot and cold working. The results are analysed in a wide test temperature range, which varies from room temperature to 300 °C, and from material previously processed by angular channel extrusion or with no previous strain accumulated. It is shown that the flow rule proposed is effective to model the material behaviour in a wide temperature range and it makes it possible to take the recrystallization phenomena that appear in previously deformed materials into account. In addition, the results obtained are compared with those predicted by other flow rules that exist in the prior literature. Furthermore, the study is complemented with finite element simulations and with a comparison between simulation and experimental results.
Open Access
Design and optimization of the dies for the isothermal forging of a cam
(Elsevier, 2015) Salcedo Pérez, Daniel; Luis Pérez, Carmelo; Luri Irigoyen, Rodrigo; León Iriarte, Javier; Puertas Arbizu, Ignacio; Fuertes Bonel, Juan Pablo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
In the present study, the design of the dies required for the isothermal forging of a cam is analysed by finite volume method. Specifically, cams are of great importance in automotive industry, where a lower weight and an improvement in the lubrication or in the materials to be in contact lead to a significant reduction in the fuel cost. The flow stress curves of one Al-Mg alloy were firstly determined by using compression tests. Once these flow stress curves were obtained, FV simulation was employed. In the forging process, the optimum die configuration has been selected. To this end, several aspects have been taken into account such as the force required for the forging, the correct die filling, the introduced plastic strain and the damage imparted to the billet.
Open Access
Design and mechanical properties analysis of AA5083 ultrafine grained cams
(MDPI, 2017) Salcedo Pérez, Daniel; Luis Pérez, Carmelo; Luri Irigoyen, Rodrigo; Puertas Arbizu, Ignacio; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
This present research work deals with the development of ultrafine grained cams obtained from previously ECAP (Equal Channel Angular Pressing)-processed material and manufactured by isothermal forging. The design and the manufacturing of the dies required for the isothermal forging of the cams are shown. Optimization techniques based on the combination of design of experiments, finite element and finite volume simulations are employed to develop the dies. A comparison is made between the mechanical properties obtained with the cams manufactured from material with no previous deformation and with those from previously SPD (Severe Plastic Deformation)-processed material. In addition, a comparative study between the experimental results and those obtained from the simulations is carried out. It has been demonstrated that it is possible to obtain ultrafine grained cams with an increase of 10.3% in the microhardness mean value as compared to that obtained from material with no previous deformation.
Open Access
Spacing roughness parameters analysis on the EDM of Inconel (R) 600 alloy
(Elsevier, 2017) Torres Salcedo, Alexia; Puertas Arbizu, Ignacio; Luis Pérez, Carmelo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Many research studies may be found regarding the measurement of surface roughness parameters. Most of them are focused on amplitude parameters as they are the most commonly used in industry, while little research has been found on the spacing ones. Spacing roughness parameters measure the horizontal characteristics of the surface deviations. In this present study, the influence of current intensity, pulse time and duty cycle on spacing roughness parameters Sm and Pc has been analyzed. Design of experiments techniques are used in order to both model and predict the most influential factors by using a small number of experiments. Current intensity of 2 A, pulse time of 25 mu s and duty cycle of 0.5 are selected as the best machining conditions in order to obtain the lowest surface roughness.
Open Access
Mechanical properties analysis of an Al-Mg alloy connecting rod with submicrometric structure
(MDPI, 2015) León Iriarte, Javier; Salcedo Pérez, Daniel; Murillo Crespo, Óscar; Luis Pérez, Carmelo; Fuertes Bonel, Juan Pablo; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Over these last few years, there has been a growing interest in developing mechanical components from submicrometric materials due to the significant improvement that these materials present compared to their original state. This present research work deals with the study of the mechanical properties of a connecting rod isothermally forged from different starting materials. These materials are as follows: annealed aluminum alloy (AA) 5754, the same alloy previously deformed through equal channel angular pressing (ECAP) and a third case where the previously ECAP-processed material is subjected to a recovery heat treatment. A comparison is made between finite volume (FV) simulations and experimental tests with respect to hardness, plastic strain and forging force. Furthermore, the improvement in the mechanical properties of the connecting rod forged from predeformed material is evaluated in comparison to the connecting rod forged with annealed material. The microstructure of both cases is also compared at the end of the manufacturing process.
Open Access
Analytical modelling of energy density and optimization of the EDM machining parameters of Inconel 600
(MDPI, 2017) Torres Salcedo, Alexia; Puertas Arbizu, Ignacio; Luis Pérez, Carmelo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
In this present research work, a new modelling of energy density in EDM (Electrical Discharge Machining) is proposed. Energy density can be defined as the amount of energy needed to get a unit volume of material removed, and for its modelling, the whole EDM process has been taken into account. This new definition lets us quantify the energy density that is being absorbed by the workpiece and the electrode. Results are compared to those obtained by die sinking EDM in an Inconel ®600 alloy using Cu-C electrodes. Currently, this material is of great interest for industrial applications in the nuclear, aeronautical and chemical sectors, due to their combinations of good mechanical properties, corrosion resistance and extreme hardness at very high temperatures. The experimental results confirm that the use of negative polarity leads to a higher material removal rate, higher electrode wear and higher surface roughness. Moreover, the optimal condition to obtain a maximum MRR (Material Removal Rate) of 30.49 mm3/min was: 8 A, 100 µs and 0.6, respectively, for the current intensity, pulse time and duty cycle.
Open Access
Design, optimization, and mechanical property analysis of a submicrometric aluminium alloy connecting rod
(Hindawi, 2015) Fuertes Bonel, Juan Pablo; León Iriarte, Javier; Luis Pérez, Carmelo; Salcedo Pérez, Daniel; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Ultrafine grained materials have a great deal of both scientific and technological interest because they allow outstanding properties to be obtained. An improvement in the mechanical strength and in the ductility and a better fatigue behaviour are properties to be expected with these materials. However, in spite of the great number of scientific publications that deals with the mechanical property improvement, the number of practical applications of these materials is scant. In this present research work, equal channel angular pressing (ECAP) is used as a severe plastic deformation process (SPD) to obtain billets which are subsequently isothermally forged to obtain a connecting rod with submicrometric grain size. The optimization of the design process is shown as well as the die design. The objective variables to be fulfilled are the correct filling of the die and the required force to obtain the part. Moreover, a comparison is also included between the mechanical properties thus obtained and those obtained with traditional methods. Moreover, optical and SEM micrographs are also included in this research work.
Open Access
Optimal machining strategy selection in ball-end milling of hardened steels for injection molds
(MDPI, 2019) Buj Corral, Irene; Ortiz Marzo, Jose Antonio; Costa Herrero, Lluís; Vivancos Calvet, Joan; Luis Pérez, Carmelo; Ingeniería; Ingeniaritza
In the present study, the groups of cutting conditions that minimize surface roughness and its variability are determined, in ball-end milling operations. Design of experiments is used to define experimental tests performed. Semi-cylindrical specimens are employed in order to study surfaces with different slopes. Roughness was measured at different slopes, corresponding to inclination angles of 15 degrees, 45 degrees, 75 degrees, 90 degrees, 105 degrees, 135 degrees and 165 degrees for both climb and conventional milling. By means of regression analysis, second order models are obtained for average roughness Ra and total height of profile Rt for both climb and conventional milling. Considered variables were axial depth of cut a(p), radial depth of cut a(e), feed per tooth f(z,) cutting speed v(c,) and inclination angle Ang. The parameter a(e) was the most significant parameter for both Ra and Rt in regression models. Artificial neural networks (ANN) are used to obtain models for both Ra and Rt as a function of the same variables. ANN models provided high correlation values. Finally, the optimal machining strategy is selected from the experimental results of both average and standard deviation of roughness. As a general trend, climb milling is recommended in descendant trajectories and conventional milling is recommended in ascendant trajectories. This study will allow the selection of appropriate cutting conditions and machining strategies in the ball-end milling process.
Open Access
Manufacturing of nanostructured rings from previously ECAE-processed AA5083 alloy by isothermal forging
(Hindawi, 2013) Luis Pérez, Carmelo; Salcedo Pérez, Daniel; León Iriarte, Javier; Puertas Arbizu, Ignacio; Fuertes Bonel, Juan Pablo; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
The manufacturing of a functional hollow mechanical element or ring of the AA5083 alloy previously equal channel angular extrusion (ECAE) processed, which presents a submicrometric microstructure, is dealt with. For this purpose, the design of two isothermal forging dies (preform and final shape) is carried out using the design of experiments (DOE) methodology. Moreover, after manufacturing the dies and carrying out tests so as to achieve real rings, themechanical properties of these rings are analysed as well as their microstructure. Furthermore, a comparison between the different forged rings is made fromECAE-processedmaterial subjected to different heat treatments, previous to the forging stage. On the other hand, the ring forging process ismodelled through the use of finite element simulation in order to improve the die design and to study the force required for the isothermal forging, the damage value, and the strain thematerial predeformed by ECAE has undergone.With this present research work, it is intended to improve the knowledge about the mechanical properties of nanostructured material and the applicability of this material to industrial processes that allow the manufacturing of functional parts.