Open Access
Increasing the sensitivity of an optic level sensor with a wavelength and phase sensitive single-mode multimode single-mode (SMS) fiber structure
(IEEE, 2017) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Vento Álvarez, José Raúl; Socorro Leránoz, Abián Bentor; Gallego Martínez, Elieser Ernesto; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The sensitivity of a liquid level sensor based on a single-mode-multimode-single-mode fiber structure has been increased by hydrofluoric acid etching. The etching process was analyzed and monitored both theoretical and experimentally, which permitted to observe that a sinusoidal spectrum can be obtained for low diameters. As an example, a 2.77 fold sensitivity increase was attained by etching from diameter 125 to 50 μm. Moreover, the sinusoidal shape of the optical spectrum permitted to monitor liquid level changes both in wavelength and phase. The cross sensitivity of the sensor to refractive index and temperature was also studied.
Open Access
Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides
(Nature Research, 2019) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua, 2018/PC021-022
The deposition of an indium oxide (In2O3) thin film on conventional planar waveguides (a coverslip and a glass slide) allows generating lossy mode resonances (LMR) by lateral incidence of light on the waveguide and by registering the optical spectrum in a spectrometer. This novel sensing system becomes an alternative to optical fibre, the substrate where LMR-based sensors have been developed so far, since it is easier to handle and more robust. An additional advantage is that cost effective waveguides, such as slides or coverslips, can be used in a platform that resembles surface plasmon resonance-based sensors in the Kretschmann configuration but without the need for a coupling prism and with the advantage of being able to generate TE and TM LMR resonances with metallic oxide or polymer thin films. The results are corroborated with simulations, which provide in-depth understanding of the phenomena involved in the sensing system. As a proof-of-concept for the optical platform, two refractometers were developed, one with low sensitivity and for a wide range of refractive indices, and the other with higher sensitivity but for a narrower refractive index range. The sensors presented here open up the path for the development of LMR-based chemical sensors, environmental sensors, biosensors, or even the generation of other optical phenomena with the deposition of multilayer structures, gratings or nanostructures, which is much easier in a planar waveguide than in an optical fibre.
Open Access
Generation of lossy mode resonances in planar waveguides toward development of humidity sensors
(IEEE, 2019) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Del Villar, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Lossy mode resonances (LMRs) are typically obtained with optical fibre. The Kretschmann configuration is an alternative but LMRs are generated with angles approaching grazing incidence. In this work, a new setup is explored, based on the lateral incidence of light on conventional planar waveguides such as glass slides or coverslips. Indium tin oxide was deposited onto both types of waveguides generating LMRs. The results of the simulations carried out agree well with the experimental results. As an example of the potential of this new and simple optical configuration, a humidity sensor with a sensitivity of 0.212 nm/% relative humidity (RH) in the range from 65% to 90% of RH was developed, which expedites the development of other types of sensors already explored with LMR-based optical fibre sensors.
Open Access
Optical fiber vacuum sensor based on modal interferometer and PDMS coating
(IEEE, 2019) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors.
Open Access
AC/DC millivoltage sensor by means of ITO-coated optical fibers: towards monitoring of biosignals
(IEEE, 2019) Aginaga Etxamendi, Concepción Isabel; Socorro Leránoz, Abián Bentor; Fuentes Lorenzo, Omar; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
This contribution shows the monitoring of AC and DC millivoltage signals by means of lossy mode resonances generated by Indium Tin Oxide (ITO) on optical fibers. Sensors were obtained by sputtering ITO thin-films onto 25 mm-length segments of 200 μm bare optical fibers. Depositing a 1 μm thin-film of ITO leads to obtain reduced thin-film resistances of near 340 ohms. This allows the detection of voltage signals by monitoring the wavelength shift of the resonances. Sensitivities up to 40 nm/V can be achieved when tracking sinusoidal signals of a few cents of mV peak-to-peak. This opens the path for further research pursuing the detection of biomedical signals.
Open Access
Optimized strain long-period fiber grating (LPFG) sensors operating at the dispersion turning point
(IEEE, 2018) Del Villar, Ignacio; Fuentes Lorenzo, Omar; Chiavaioli, Francesco; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako Gobernua
Two phenomena for enhancing the sensitivity of longperiod fiber gratings are combined toward an increase of the sensitivity to strain of this type of devices: the dispersion turning point (DTP) and the cladding diameter reduction by an etching process. The results prove that sensitivities up to 20 pm/με can be attained, which is a ten-fold improvement compared to the previous works. The sensitivity in the grating region, which is subjected to etching, does not depend on the order of the cladding mode responsible for the attenuation bands generated in the transmission spectrum, but on the proximity to the DTP for each mode order. On the other hand, the sensitivity to strain of the global structure, including the region without etching, can be increased for lower order modes in a perceptible way if the length of the etched region is smaller compared to the fiber region under stress. The experimental results are supported with simulations based on coupled-mode theory and on FIMMWAVE, which allows understanding the phenomena involved during the sensing process.