Listar Artículos de revista - Aldizkari artikuluak por autor UPNA "Gandía Pascual, Luis"
Mostrando ítems 1-20 de 42
-
The 3D-printing fabrication of multichannel silicone microreactors for catalytic applications
Microstructured reactors (MSRs) are especially indicated for highly demanding heterogeneous catalysis due to the small channel dimensions that minimize diffusional limitations and enhance mass and heat transport between ... -
Acid-catalyzed etherification of glycerol with tert-butanol: reaction monitoring through a complete identification of the produced alkyl ethers
Higher tert-Butyl glycerol ethers (tBGEs) are interesting glycerol derivatives that can be produced from tert-butyl alcohol (TBA) and glycerol using an acid catalyst. Glycerol tert-butylation is a complex reaction that ... -
Acoustic and psychoacoustic levels from an internal combustion engine fueled by hydrogen vs. gasoline
Whereas noise generated by road traffic is an important factor in urban pollution, little attention has been paid to this issue in the field of hydrogen-fueled vehicles. The objective of this study is to analyze the influence ... -
Application of a modeling tool to describe fly ash generation, composition, and melting behavior in a wheat straw fired commercial power plant
Ash behavior is a key operational aspect of industrial-scale power generation by means of biomass combustion. In this work, FactSage™ 6.4 software was used to develop and assess three models of wheat straw combustion in a ... -
Application of eco-design and life cycle assessment standards for environmental impact reduction of an industrial product
Eco-design is included within the framework of the standard for “Environmental management systems—Guidelines for incorporating Eco-design” (ISO 14006:2011). Eco-design process, as defined in standard, has six steps: (i) ... -
Catalytic performance of bulk and Al₂O₃-supported molybdenum oxide for the production of biodiesel from oil with high free fatty acids content
Non-edible vegetable oils are characterized by high contents of free fatty acids (FFAs) that prevent from using the conventional basic catalysts for the production of biodiesel. In this work, solid acid catalysts are used ... -
Characterization of combustion anomalies in a hydrogen-fueled 1.4 L commercial spark-ignition engine by means of in-cylinder pressure, block-engine vibration, and acoustic measurements
Abnormal combustion phenomena are among the main hurdles for the introduction of hydrogen in the transportation sector through the use of internal combustion engines (ICEs). For that reason the challenge is to guarantee ... -
CO2 methanation over nickel catalysts: support effects investigated through specific activity and operando IR spectroscopy measurement
Renewed interest in CO2 methanation is due to its role within the framework of the Power-to-Methane processes. While the use of nickel-based catalysts for CO2 methanation is well stablished, the support is being subjected ... -
Comparative performance of coke oven gas, hydrogen and methane in a spark ignition engine
In this study, coke oven gas (COG), a by-product of coke manufacture with a high volumetric percentage of H2 and CH4, has been identified as auxiliary support and promising energy source in stationary internal combustion ... -
Comparative study of supported Ni and Co catalysts prepared using the All-in-One method in the hydrogenation of CO2: effects of using (Poly)Vinyl Alcohol (PVA) as an additive
Two series of Ni and Co catalysts supported onto La-Al2O3 were prepared and the CO2 hydrogenation reactions investigated. The catalytic performance was evaluated in terms of the evolution with the reaction temperature of ... -
Conversion of a commercial gasoline vehicle to run bi-fuel (hydrogen-gasoline)
Bi-fuel internal combustion engine vehicles allowing the operation with gasoline or diesel and hydrogen have great potential for speeding up the introduction of hydrogen in the transport sector. This would also contribute ... -
Conversion of a commercial spark ignition engine to run on hydrogen: performance comparison using hydrogen and gasoline
The modifications performed to convert the spark ignition gasoline-fueled internal combustion engine of a Volkswagen Polo 1.4 to run with hydrogen are described. The car is representative of small vehicles widely used for ... -
Conversion of a gasoline engine-generator set to a bi-fuel (hydrogen/gasoline) electronic fuel-injected power unit
The modifications performed to convert a gasoline carbureted engine-generator set to a bi-fuel (hydrogen/gasoline) electronic fuel-injected power unit are described. Main changes affected the gasoline and gas injectors, ... -
Effect of oxygen addition, reaction temperature and thermal treatments on syngas production from biogas combined reforming using Rh/alumina catalysts
Dry reforming and partial oxidation of biogas were studied using 0.5 wt.% Rh/Al2O3 catalysts, both inhouse prepared and commercial. The effects of O2 addition on syngas yield and biogas conversion were studied at 700 C ... -
Environmental impact improvement of chitosan-based mixed-matrix membranes manufacture for CO2 gas separation by life cycle assessment
The environmental impacts of the manufacture of chitosan (CS) and polymeric poly(1-trimethylsilyl-1-propyne) (PTMSP) mixed-matrix membranes (MMMs) for CO2 separation by life cycle assessment (LCA) are compared. An ionic ... -
Experimental study of the performance and emission characteristics of an adapted commercial four-cylinder spark ignition engine running on hydrogen-methane mixtures
The use of hydrogen/methane mixtures with low methane contents as fuels for internal combustion engines (ICEs) may help to speed up the development of the hydrogen energy market and contribute to the decarbonization of the ... -
Exploring a low-cost valorization route for amazonian cocoa pod husks through thermochemical and catalytic upgrading of pyrolysis vapors
Ecuador as an international leader in the production of cocoa beans produced more than 300 000 tons in 2021; hence, the management and valorization of the 2 MM tons of waste generated annually by this industry have a ... -
Extraction of phenolic compounds from populus salicaceae bark
Lignocellulosic residues have the potential for obtaining high value-added products that could be better valorized if biorefinery strategies are adopted. The debarking of short-rotation crops yields important amounts of ... -
Functionalization of 3D printed ABS filters with MOF for toxic gas removal
Acrylonitrile butadiene styrene (ABS) is one of the most extensively used polymer in 3D printing manufacturing due to its competitive thermal and mechanical properties. Recently, a special attention has been devoted to ... -
Gaseous fueling of an adapted commercial automotive spark-ignition engine: simplified thermodynamic modeling and experimental study running on hydrogen, methane, carbon monoxide and their mixtures
In the present work, methane, carbon monoxide, hydrogen and the binary mixtures 20 % CH4–80 % H2, 80 % CH4–20 % H2, 25 % CO–75 % H2 (by volume) were considered as fuels of a naturally aspirated port-fuel injection four-cylinder ...