Open Access
Heterogeneous Fenton- and photo-Fenton-like catalytic degradation of emerging pollutants using Fe2O3/TiO2/pillared clays synthesized from aluminum industrial wastes
(Elsevier, 2023-04-01) Cardona Rodríguez, Yaneth; Wegrzyn, Agnieszka; Miskowiec, Pawel; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The presence of emerging pollutants (EPs) in water is a major environmental concern. This study evaluates for the first time the removal of three EPs, namely triclosan (TCS), 2,6-dichlorophenol (2,6-DCP), and bisphenol A (BPA), 90 μmol/dm3, from water through both Fenton- and photo-Fenton-like reactions using montmorillonite (Mt) and aluminum interlayered pillared clays (Al-PILC) as catalytic supports. The catalysts (Fe2O3/TiO2/Mt and Fe2O3/TiO2/Al-PILC) were evaluated in single-component solutions and in an equimolar mixture. Two Al-PILC were synthesized from a hazardous waste, namely aluminum saline slag, using either the acid (Al-PILCAE) or the alkaline (Al-PILCBE) aluminum extract as precursors. The third Al-PILC was obtained by the conventional method using a commercial aluminum salt (Al-PILCCM). Catalytic supports were impregnated at 10 and 20 wt% titanium. Iron loadings from 1 to 20 wt% were tested for Mt, while only 20 wt% iron was tested for Al-PILC. All catalysts were characterized using several techniques and the results confirmed the formation of TiO2 and Fe2O3. Almost 100 % of TCS and 2,6-DCP were removed by both Fenton-like (240 and 420 min, respectively) and photo-Fenton-like reactions (30 and 90–120 min, respectively) using the Al-PILC based catalyst. The maximum removal for BPA was 80.14 ± 1.93 % after 120 min under photo-Fenton-like conditions using Al-PILCBE. The catalysts synthesized using the four catalytic supports showed good results for the removal of TCS by both processes, while for 2,6-DCP and BPA the best results were obtained using Al-PILCAE and Al-PILCBE as catalytic supports. Finally, a degradation pathway was suggested for every pollutant based on the by-products identified during the reactions by HPLC-MS. The results revealed that the materials used in this work are suitable catalysts for removing emerging pollutants from water by both Fenton- and photo-Fenton-like reactions.
Open Access
Catalytic photodegradation of organic compounds using TiO2/pillared clays synthesized using a nonconventional aluminum source
(Elsevier, 2022-10-15) Cardona Rodríguez, Yaneth; Wegrzyn, Agnieszka; Miskowiec, Pawel; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This study evaluates the photocatalytic degradation of 2,6-dichlorophenol (2,6-DCP), triclosan (TCS) and bisphenol A (BPA) by ultraviolet (UV) and visible (VIS) light in the presence of TiO2/catalysts synthesized by wet impregnation followed by calcination. The catalyst supports used were three alumina pillared clays (Al-PILC) synthesized using various aluminum sources and montmorillonite (Mt) as raw material. One of the Al-PILC was prepared following the conventional method (Al-PILCCM), using a commercial aluminum salt, and the other two were synthesized using a saline slag, with the aluminum used being extracted with the alkaline (Al-PILCBE) or the acid (Al-PILCAE) method. Mt was impregnated with various amounts of titanium (1, 5, 10, and 20 wt% Ti) and evaluated for the photodegradation of the aforementioned pollutants, comparing the results with those obtained using commercial anatase. Due to the higher conversion rates, 10 and 20 wt% Ti were chosen to impregnate the Al-PILC and to evaluate the photocatalytic performance. All materials were characterized by several techniques, which confirmed the successful formation of TiO2 in the anatase phase. In all cases, photodegradation was higher when using UV light and the most photodegraded pollutant was TCS (85.15 ± 0.49%), followed by 2,6-DCP (65.43 ± 0.79%) and, to a lesser degree, BPA (36.15 ± 0.65%). Al-PILC showed higher photodegradation percentages, with Al-PILCAE exhibiting the highest values for both types of light. An analysis of the photoproducts by HPLC-MS suggested that the preferred pathway for TCS and 2,6-DCP photodegradation depends on the type of light used.

Cardona Rodríguez, Yaneth

Email Address

person.page.identifierURI

Birth Date

Job Title

Last Name

First Name

person.page.departamento

person.page.instituteName

ORCID

person.page.observainves

person.page.upna

Name

Filters

Author

Subject

Date

Has files

Item Type

Type

Settings

Sort By

Results per page

Search Results