Open Access
Synthesis of rectangular waveguide filters with smooth profile oriented to direct metal additive manufacturing
(IEEE, 2023) Percaz Ciriza, Jon Mikel; Hussain, Jabir; Arregui Padilla, Iván; Teberio Berdún, Fernando; Benito Pertusa, David; Martín Iglesias, Petronilo; Arnedo Gil, Israel; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a novel design method for rectangular waveguide filters intended for fabrication using direct metal additive manufacturing is proposed. The synthesized filters will feature a smooth profile that allows us to fabricate them orienting the filter propagation axis in the vertical building direction, achieving an optimum configuration for direct metal additive manufacturing fabrication. The novel design method is valid for any all-pole transfer function, which is initially implemented with a commensurate-line distributed unit element prototype. The impulse response of that initial prototype is then properly interpolated to obtain the target response for a smooth-profiled filter with similar length and profile excursion. Finally, the target impulse response just generated is implemented in rectangular waveguide technology employing a novel inverse scattering synthesis technique that relies on the coupled-mode theory to model the electromagnetic behavior of the waveguide filter. The novel inverse scattering synthesis technique is general and also valid for the case of filters with very high rejection levels, which is of great relevance in rectangular waveguide technology. A Ku-band low-pass filter with stringent satellite specifications is designed using the proposed method, fabricated by means of a direct metal additive manufacturing technique, and measured with a vector network analyzer. A very good agreement is achieved between the simulated and measured results, fulfilling the required specifications and demonstrating the feasibility and performance of the novel design method.
Open Access
Metal 3D printing for RF/microwave high-frequency parts
(Springer, 2022) Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Teberio Berdún, Fernando; Arregui Padilla, Iván; Marechal, M.; Calves, P.; Hazard, M.; Pambaguian, L.; Brandao, A.; Rodríguez Castillo, S.; Martin, T.; Percaz Ciriza, Jon Mikel; Iza, V.; Martín-Iglesias, Santiago; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Space Systems have been historically characterised by high performance, high reliability and high cost. Every new generation of space systems tends to improve performance, keep as much as possible reliability, speeding the lead time and lower the cost. Aggressive approach is nowadays followed by some of the players of the new space ecosystem where, for instance, reli- ability can be relaxed thanks for the in-orbit redundancy or robustness to failures by having a constellation with a high number of satellites. This push towards the technology and system limit requires to investigate new methods for the manufacturing of RF/Microwave parts. RF devices such as those based on waveguide structures, benefit from an additive manufacturing approach in terms of radio frequency (RF) performance and compactness. However each manufacturing approach comes with specific features and limitations which need to be well understood and, in some cases, even taking advantage of them. This paper provides a short review of some of the RF/Microwave parts already manufactured using this technology. The paper will focus mainly on metal 3D printing parts since this technology is, at the moment, well accepted by the space community.
Open Access
Improvement of corona breakdown threshold (peak power handling) in smooth-profiled microstrip filters
(2022) Ahmad, Jamil; Hussain, Jabir; Arregui Padilla, Iván; Martín Iglesias, Petronilo; Arnedo Gil, Israel; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, the PPHCs of two filter design techniques, stepped-impedance (SI) and smooth-profile (SP), are presented for four design prototypes. Smooth-profiled filters feature smooth variations in the characteristic impedance profile, avoiding sharp edges, which accumulate electric fields. The absence of sharp edges in SP reduces the voltage magnification factor, which in turn improves the PPHC of the filter. The phenomenon of electric fields accumulation at the sharp corners of the SI filters is presented and compared with smooth transitions in SP filters. Furthermore, 1D graphs of electric field intensity are presented along the strip contour of the microstrip lines. Finally, SPARK3D results clearly demonstrate that SP filters can handle higher peak powers than their SI counterparts between critical pressure and ambient pressure, for all the studied designs.
Open Access
Sistema de medición de condiciones atmosféricas basado en el estudio del flujo de muones
(Universidad de Castilla La Mancha, 2024) Armendáriz Armenteros, Miguel Ángel; Vertiz Conde, Amaia; Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Muro Pérez, Aitor; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
To date, there is no straightforward method for monitoring meteorological conditions in real-time through experimental measurements. Consequently, all weather predictions rely on forecasting models, which are unable to adapt to actual weather changes, thereby compromising their accuracy. The project described in this paper seeks to establish a weather measurement system that leverages the relationship between climatic conditions and the phenomena of cosmic ray degradation and muon generation. If this relationship is accurately defined, it could lead to the development of a model that predicts atmospheric conditions based on the flux of muons and cosmic rays and the occurrence of the aforementioned phenomena. This paper provides a theoretical foundation to support the viability of the project, outlines the proposed configuration of the system, and discusses the implementation of its most crucial components. This project was undertaken by students from the Degree in Engineering in Telecommunication Technologies at the Public University of Navarre (UPNA), within the course Projects in Telecommunication Systems
Open Access
Integrating multiple stubs in stepped-impedance filter aiming for high selectivity
(IET, 2022) Sami, Abdul; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arnedo Gil, Israel; Calero Fernández, Ibai; Teberio Berdún, Fernando; Martín Iglesias, Petronilo; Benito Pertusa, David; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband.
Open Access
Filtro paso banda en tecnología groove gap waveguide con altura de pines reducida para facilitar su fabricación
(Universidad de Málaga, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work, a novel topology of groove gap waveguide (GGW) technology is presented to facilitate the fabrication process by Computer Numerical Control (CNC) milling. GGW has been proposed as an interesting alternative to the rectangular waveguide for the design of microwave and millimeter-wave components. This technology consists of two parallel metal plates, where one of them has a (lambda)/4-height pin bed that provides a high impedance condition at the plane over the pins, avoiding electrical contact requirement with the upper plate and hence facilitating the fabrication requirements. However, the manufacture by CNC milling of the pins may be troublesome, especially for devices operating at high frequency. A way to facilitate this process is achieved by using pins with reduced height. Moreover, the proposed configuration allows us to maintain the standard dimension ports of the equivalent rectangular waveguide and the operation in its corresponding bandwidth. A comparison with other GGW topologies has been presented and a bandpass filter has been fabricated to validate its usefulness.
Open Access
Filtro de cavidades apiladas en tecnología CLAF-SIW para ondas milimétricas
(Universidad de Castilla-La Mancha, 2024) Segura-Gómez, Cleofás; Biedma-Pérez, Andrés; Santiago Arriazu, David; Palomares-Caballero, Ángel; Arregui Padilla, Iván; Gómez Laso, Miguel Ángel; Padilla, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Este trabajo presenta la validación de la tecnología CLAF-SIW para la fabricación de filtros en el rango de frecuencias de ondas milimétricas. El filtro estudiado es un filtro paso banda compuesto por cuatro cavidades apiladas y acopladas mediante iris (se utilizan cinco iris en total). Cada capa está compuesta por una placa de circuito impreso (PCB) de espesor comercial. Las capas de iris se prototipan metalizando los bordes de las ranuras, mientras que las capas de cavidad contienen la estructura CLAF-SIW utilizando setas dobles como estructura EBG. El filtro se obtiene inmediatamente simplemente adaptando el ancho efectivo de la cavidad CLAF-SIW a la cavidad de referencia, para la cual se han estudiado los efectos que afectan a este valor efectivo. Se ha fabricado un prototipo con buena concordancia entre la medición, la simulación y la respuesta ideal del filtro de cavidad para una banda de paso de 36 a 37,5 GHz. Las pequeñas discrepancias se deben a las diferencias en la separación real entre los laminados y las tolerancias de fabricación.
Open Access
Passive microwave component design using inverse scattering: theory and applications
(Hindawi, 2013) Arnedo Gil, Israel; Arregui Padilla, Iván; Chudzik, Magdalena; Teberio Berdún, Fernando; Lujambio Genua, Aintzane; Benito Pertusa, David; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
We briefly review different synthesis techniques for the design of passive microwave components with arbitrary frequency response, developed by our group during the last decade. We provide the theoretical foundations based on inverse scattering and coupledmode theory as well as several applications where the devices designed following those techniques have been successfully tested. The main characteristics of these synthesis methods are as follows. (a) They are direct, because it is not necessary to use lumpedelement circuit models; just the target frequency response is the starting point. (b)They are exact, as there is neither spurious bands nor degradation in the frequency response; hence, there is no bandwidth limitation. (c) They are flexible, because they are valid for any causal, stable, and passive transfer function; only inviolable physical principles must be guaranteed. A myriad of examples has been presented by our group in many different technologies for very relevant applications such as harmonic control of amplifiers, directional couplerwith enhanced directivity and coupling, transmission-type dispersive delay lines for phase engineering, compact design of high-power spurious free low-pass waveguide filters for satellite payloads, pulse shapers for advanced UWB radar and communications and for novel breast cancer detection systems, transmission-type Nth-order differentiators for tunable pulse generation, and a robust filter design tool.
Open Access
Gap waveguide topology with reduced height pins for millimeter-wave components
(URSI Publications, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A new topology for groove gap waveguide (GGW) technology is proposed to ease its manufacturing process by computer numerical control (CNC) milling. GGW technology consists of two metal plates, where one of them presents a λ/4 height pin bed that avoids contact with the other plate, making it an ideal alternative to other waveguides for millimeterwave applications. However, the manufacture of the pins by CNC milling may be troublesome due to the large pin height required. A GGW with reduced height pins will be proposed, maintaining the standard dimensions of the equivalent rectangular waveguide ports and the operation bandwidth. The performance of this new topology will be compared with other proposals by means of simulations and measurements, and a bandpass filter will be also implemented and manufactured in this technology to validate its usefulness.
Open Access
Synthesis of one dimensional electromagnetic bandgap structures with fully controlled parameters
(IEEE, 2017) Arnedo Gil, Israel; Chudzik, Magdalena; Percaz Ciriza, Jon Mikel; Arregui Padilla, Iván; Teberio Berdún, Fernando; Benito Pertusa, David; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, we propose a novel synthesis strategy for the design of one dimensional electromagnetic bandgap (1- D-EBG) structures where all the performance parameters of these devices can fully be controlled, i.e., the central frequency of the forbidden band, its attenuation level and bandwidth, and the ripple level at the passbands. The novel synthesis strategy employs a new inverse-scattering technique to accurately synthesize the 1-D-EBG structure, targeting a properly interpolated version of a classical periodic filter fulfilling the required frequency specifications. The new inverse-scattering technique follows a continuous layer peeling approach and relies on the coupled-mode theory to precisely model the microwave structures. Telecommunication and radar systems, as well as material characterization devices, will be profited by this proposal with which enhanced filters, sensors, power dividers, couplers, mixers, oscillators, and amplifiers can be designed in many different technologies. As a proof of concept, a 1-D-EBG structure in microstrip technology with a single forbidden band (free of spurious stopband replicas), with attenuation level of 30 dB, fractional bandwidth larger than 100%, and return loss level at the passbands of 20 dB, has been designed and fabricated. The measurements obtained are in very good agreement with the simulations and target specifications, being free of spurious replicas up to the 15th harmonic, showing the robustness and very good performance of the novel design strategy proposed.