Open Access
Filtro de cavidades apiladas en tecnología CLAF-SIW para ondas milimétricas
(Universidad de Castilla-La Mancha, 2024) Segura-Gómez, Cleofás; Biedma-Pérez, Andrés; Santiago Arriazu, David; Palomares-Caballero, Ángel; Arregui Padilla, Iván; Gómez Laso, Miguel Ángel; Padilla, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
Este trabajo presenta la validación de la tecnología CLAF-SIW para la fabricación de filtros en el rango de frecuencias de ondas milimétricas. El filtro estudiado es un filtro paso banda compuesto por cuatro cavidades apiladas y acopladas mediante iris (se utilizan cinco iris en total). Cada capa está compuesta por una placa de circuito impreso (PCB) de espesor comercial. Las capas de iris se prototipan metalizando los bordes de las ranuras, mientras que las capas de cavidad contienen la estructura CLAF-SIW utilizando setas dobles como estructura EBG. El filtro se obtiene inmediatamente simplemente adaptando el ancho efectivo de la cavidad CLAF-SIW a la cavidad de referencia, para la cual se han estudiado los efectos que afectan a este valor efectivo. Se ha fabricado un prototipo con buena concordancia entre la medición, la simulación y la respuesta ideal del filtro de cavidad para una banda de paso de 36 a 37,5 GHz. Las pequeñas discrepancias se deben a las diferencias en la separación real entre los laminados y las tolerancias de fabricación.
Open Access
Diseño de filtros en tecnología de línea coaxial sin dieléctricos mediante impresión 3D
(Universidad de Castilla La Mancha, 2024) Pons Abenza, Alejandro; Arregui Padilla, Iván; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Álvarez Botero, Germán Andrés; Martín Iglesias, Petronilo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
This article presents the design and manufacturing of a fully metallic X-band bandpass filter in coaxial-line technology. The device is 3D-printed as a self-supported structure without any dielectric inside. A short-circuit λ/4 parallel stub bandpass filter provides the required mechanical support for the self-supported 3D-printing process. To enhance filter out-of-band performance, a second stage consisting of a stepped-impedance low-pass filter is integrated, also using coaxial-line technology. Both filters are designed separately and then combined to achieve desired frequency specifications. A prototype with a passband at X-band (between 8 and 12 GHz) is manufactured using Selective Laser Melting, showing excellent agreement between simulations and measurements. This approach promises highly integrated, multifunctional monoblock coaxial filters with additional benefits such as increased RF shielding and protection against electrostatic discharge.
Open Access
Sistema de medición de condiciones atmosféricas basado en el estudio del flujo de muones
(Universidad de Castilla La Mancha, 2024) Armendáriz Armenteros, Miguel Ángel; Vertiz Conde, Amaia; Martín Iglesias, Petronilo; Gómez Laso, Miguel Ángel; Muro Pérez, Aitor; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
To date, there is no straightforward method for monitoring meteorological conditions in real-time through experimental measurements. Consequently, all weather predictions rely on forecasting models, which are unable to adapt to actual weather changes, thereby compromising their accuracy. The project described in this paper seeks to establish a weather measurement system that leverages the relationship between climatic conditions and the phenomena of cosmic ray degradation and muon generation. If this relationship is accurately defined, it could lead to the development of a model that predicts atmospheric conditions based on the flux of muons and cosmic rays and the occurrence of the aforementioned phenomena. This paper provides a theoretical foundation to support the viability of the project, outlines the proposed configuration of the system, and discusses the implementation of its most crucial components. This project was undertaken by students from the Degree in Engineering in Telecommunication Technologies at the Public University of Navarre (UPNA), within the course Projects in Telecommunication Systems
Open Access
Multipactor breakdown analysis of Ku-band meandered low-pass filter
(2022) Sami, Abdul; Teberio Berdún, Fernando; Arnedo Gil, Israel; Martín Iglesias, Petronilo; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, a very compact rectangular waveguide low-pass filter with meandered topology based on commensurate lines for Ku-band satellite applications is analysed for high-power handling capabilities. The device consists of rectangular waveguide sections properly cascaded to form a meandered topology to obtain the desired value of the local reflection coefficients. which are essential to achieve the target frequency response and also to keep large mechanical gaps. Hence, this technique allows us not only to design a filter with compact size but a filter geometry which is suitable for high power applications. In the paper, the low-pass filter based on commensurate lines is first designed by cascading E-plane mitered bends (±90° EMBs) in CST Microwave Studio (MWS) and then the values of the electromagnetic fields at the passband frequencies are exported to Spark3D to perform a multipactor analysis. The critical areas inside the device where the multipactor discharge occurs will also be identified in the high-power analysis. https://doi.org/10.5281/zenodo.7343236
Open Access
Assessment of performance of one-turn inductors in series configuration through a transmission-line modeling approach
(IEEE , 2024) Álvarez Botero, Germán Andrés; Moctezuma-Pascual, Eduardo; Gómez Laso, Miguel Ángel; Torres-Torres, Reydezel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza
In this paper, transmission-line theory is applied to implement a physical model for compact one-turn inductors, which simultaneously incorporates the frequency-dependent effects introduced by the conductor skin effect and the loss originated by the coupling with the ground plane. For this purpose, S-parameter measurements are processed to extract the associated parameters, which exhibit scalability with the turn radius. This allows the model to be used for interpolation and extrapolation analyses. In this regard, the device performance is assessed for one-turn inductors in series connection, for different load impedances, and when the turn is narrowed. To validate the proposal, agreement between the model and the experimental transmission line RLGC parameters, the return loss, and the Q-factor is obtained up to 20 GHz.
Open Access
Filtro paso banda en tecnología groove gap waveguide con altura de pines reducida para facilitar su fabricación
(Universidad de Málaga, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work, a novel topology of groove gap waveguide (GGW) technology is presented to facilitate the fabrication process by Computer Numerical Control (CNC) milling. GGW has been proposed as an interesting alternative to the rectangular waveguide for the design of microwave and millimeter-wave components. This technology consists of two parallel metal plates, where one of them has a (lambda)/4-height pin bed that provides a high impedance condition at the plane over the pins, avoiding electrical contact requirement with the upper plate and hence facilitating the fabrication requirements. However, the manufacture by CNC milling of the pins may be troublesome, especially for devices operating at high frequency. A way to facilitate this process is achieved by using pins with reduced height. Moreover, the proposed configuration allows us to maintain the standard dimension ports of the equivalent rectangular waveguide and the operation in its corresponding bandwidth. A comparison with other GGW topologies has been presented and a bandpass filter has been fabricated to validate its usefulness.
Open Access
Integrating multiple stubs in stepped-impedance filter aiming for high selectivity
(IET, 2022) Sami, Abdul; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arnedo Gil, Israel; Calero Fernández, Ibai; Teberio Berdún, Fernando; Martín Iglesias, Petronilo; Benito Pertusa, David; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband.
Open Access
Gap waveguide topology with reduced height pins for millimeter-wave components
(URSI Publications, 2022) Santiago Arriazu, David; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arregui Padilla, Iván; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
A new topology for groove gap waveguide (GGW) technology is proposed to ease its manufacturing process by computer numerical control (CNC) milling. GGW technology consists of two metal plates, where one of them presents a λ/4 height pin bed that avoids contact with the other plate, making it an ideal alternative to other waveguides for millimeterwave applications. However, the manufacture of the pins by CNC milling may be troublesome due to the large pin height required. A GGW with reduced height pins will be proposed, maintaining the standard dimensions of the equivalent rectangular waveguide ports and the operation bandwidth. The performance of this new topology will be compared with other proposals by means of simulations and measurements, and a bandpass filter will be also implemented and manufactured in this technology to validate its usefulness.
Open Access
High-power filter design in waveguide technology: future generation of waveguide satellite filters in payloads handling increasing bit rates and numbers of channels
(IEEE, 2020) Arregui Padilla, Iván; Teberio Berdún, Fernando; Arnedo Gil, Israel; Percaz Ciriza, Jon Mikel; Martín Iglesias, Petronilo; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
To design a filter for a particular application, many issues must first be considered. Which technology will be the most convenient? What design technique will provide better results for a particular set of frequency specifications? Once the device has been designed, will it fulfill all of the (not only electrical) requirements? It is not always easy to answer such questions in advance. In this article, we try to shed some light on these questions when our aim is the design of filters for high-power operation.
Open Access
Synthesis of rectangular waveguide filters with smooth profile oriented to direct metal additive manufacturing
(IEEE, 2023) Percaz Ciriza, Jon Mikel; Hussain, Jabir; Arregui Padilla, Iván; Teberio Berdún, Fernando; Benito Pertusa, David; Martín Iglesias, Petronilo; Arnedo Gil, Israel; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a novel design method for rectangular waveguide filters intended for fabrication using direct metal additive manufacturing is proposed. The synthesized filters will feature a smooth profile that allows us to fabricate them orienting the filter propagation axis in the vertical building direction, achieving an optimum configuration for direct metal additive manufacturing fabrication. The novel design method is valid for any all-pole transfer function, which is initially implemented with a commensurate-line distributed unit element prototype. The impulse response of that initial prototype is then properly interpolated to obtain the target response for a smooth-profiled filter with similar length and profile excursion. Finally, the target impulse response just generated is implemented in rectangular waveguide technology employing a novel inverse scattering synthesis technique that relies on the coupled-mode theory to model the electromagnetic behavior of the waveguide filter. The novel inverse scattering synthesis technique is general and also valid for the case of filters with very high rejection levels, which is of great relevance in rectangular waveguide technology. A Ku-band low-pass filter with stringent satellite specifications is designed using the proposed method, fabricated by means of a direct metal additive manufacturing technique, and measured with a vector network analyzer. A very good agreement is achieved between the simulated and measured results, fulfilling the required specifications and demonstrating the feasibility and performance of the novel design method.