Open Access
Influence of structural defects on the properties of metamagnetic shape memory alloys
(MDPI, 2020) Pérez de Landazábal Berganzo, José Ignacio; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Lambri, Osvaldo Agustín; López García, Javier; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The production of µ-particles of Metamagnetic Shape Memory Alloys by crushing and subsequent ball milling process has been analyzed. The high energy involved in the milling process induces large internal stresses and high density of defects with a strong influence on the martensitic transformation; the interphase creation and its movement during the martensitic transformation produces frictional contributions to the entropy change (exothermic process) both during forward and reverse transformation. The frictional contribution increases with the milling time as a consequence of the interaction between defects and interphases. The influence of the frictional terms on the magnetocaloric effect has been evidenced. Besides, the presence of antiphase boundaries linked to superdislocations helps to understand the spin-glass behavior at low temperatures in martensite. Finally, the particles in the deformed state were introduced in a photosensitive polymer. The mechanical damping associated to the Martensitic Transformation (MT) of the particles is clearly distinguished in the produced composite, which could be interesting for the development of magnetically-tunable mechanical dampers.
Open Access
Polycaprolactone/MSMA composites for magnetic refrigeration applications
(Wiley, 2024-09-06) Sánchez-Alarcos Gómez, Vicente; Khanna, Deepali; La Roca, Paulo Matías; Recarte Callado, Vicente; Lambri, Fernando Daniel; Bonifacich, Federico Guillermo; Lambri, Osvaldo Agustín; Royo Silvestre, Isaac; Urbina Yeregui, Antonio; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
A high filling load (62% weight) printable magnetic composite has been elaborated from the dispersion of magnetocaloric Ni45Mn36.7In13.3Co5 metamagnetic shape memory alloy microparticles into a PCL polymer matrix. The composite material has been prepared by solution method, resulting in a very homogeneous particles dispersion into the matrix. The structural transitions in the polymer are not affected by the addition of the metallic microparticles, which in turn results in a significant increase of the mechanical consistency. The good ductility of the elaborated composite allows its extrusion in flexible printable filaments, from which 3D pieces with complex geometries have been grown. The heat transfer of the composite material has been assessed from finite element simulation. In spite of the achievable magnetocaloric values are moderated with respect to the bulk, numerical simulations confirm that, in terms of heat transference, a PCL/Ni-Mn-In-Co wire is more efficient than a bulk Ni-Mn-In-Co cubic piece containing the same amount of magnetic active material. The quite good magnetocaloric response of the composite and the possibility to print high surface/volume ratio geometries make this material a promising candidate for the development of heat exchangers for clean and efficient magnetic refrigeration applications.
Open Access
Giant direct and inverse magnetocaloric effect linked to the same forward martensitic transformation
(Springer Nature, 2017) Pérez de Landazábal Berganzo, José Ignacio; Recarte Callado, Vicente; Sánchez-Alarcos Gómez, Vicente; Beato López, Juan Jesús; Rodríguez Velamazán, José Alberto; Sánchez Marcos, J.; Gómez Polo, Cristina; Cesari, Eduard; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física
Metamagnetic shape memory alloys have aroused considerable attraction as potential magnetic refrigerants due to the large inverse magnetocaloric effect associated to the magnetic-field-induction of a reverse martensitic transformation (martensite to austenite). In some of these alloys, the austenite phase can be retained on cooling under high magnetic fields, being the retained phase metastable after field removing. Here, we report a giant direct magnetocaloric effect linked to the anomalous forward martensitic transformation (austenite to martensite) that the retained austenite undergoes on heating. Under moderate fields of 10 kOe, an estimated adiabatic temperature change of 9 K has been obtained, which is (in absolute value) almost twice that obtained in the conventional transformation under higher applied fields. The observation of a different sign on the temperature change associated to the same austenite to martensite transformation depending on whether it occurs on heating (retained) or on cooling is attributed to the predominance of the magnetic or the vibrational entropy terms, respectively.
Open Access
Long-range atomic order and entropy change at the martensitic transformation in a Ni-Mn-In-Co metamagnetic shape memory alloy
(MDPI, 2014) Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Cesari, Eduard; Rodríguez Velamazán, José Alberto; Física; Fisika
The influence of the atomic order on the martensitic transformation entropy change has been studied in a Ni-Mn-In-Co metamagnetic shape memory alloy through the evolution of the transformation temperatures under high-temperature quenching and post-quench annealing thermal treatments. It is confirmed that the entropy change evolves as a consequence of the variations on the degree of L21 atomic order brought by thermal treatments, though, contrary to what occurs in ternary Ni-Mn-In, post-quench aging appears to be the most effective way to modify the transformation entropy in Ni-Mn-In-Co. It is also shown that any entropy change value between around 40 and 5 J/kgK can be achieved in a controllable way for a single alloy under the appropriate aging treatment, thus bringing out the possibility of properly tune the magnetocaloric effect.
Open Access
Monitoring structural transformations in metamagnetic shape memory alloys by non-contact GMI technology
(IOP Publishing, 2023) Beato López, Juan Jesús; La Roca, Paulo Matías; Algueta-Miguel, Jose M.; Garayo Urabayen, Eneko; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Different applications based on metamagnetic shape memory alloy (MSMA) require monitoring the evolution of the martensitic transformation (MT) to optimize the actuation mechanism. To avoid interaction with the active material, a non-contact technique would be ideal. Nevertheless, non-contact detection involves complex methods like diffraction, optical analysis, or electromagnetic technology. The present work demonstrates that the MT can be monitored without interaction with the active material using a low-cost technology based on the Giant Magnetoimpedance (GMI) effect. The GMI sensor is based on a (CoFe)SiB soft magnetic wire submitted to an alternating current and whose second harmonic voltage variation allows to detect changes in the strength of the stray magnetic fields linked to the metamagnetic phase transition. The sensor has been tested using the MT of a NiMnInCo MSMA. A specific application for environmental temperature control using the non-contact GMI sensor is proposed.
Open Access
Effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy
(Elsevier, 2021) López García, José Luis; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Rodríguez Velamazán, José Alberto; Unzueta, Iraultza; García, José Ángel; Plazaola, Fernando; La Roca, Paulo Matías; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Gobierno de Navarra / Nafarroako Gobernua, PC017-018 AMELEC
The effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy in austenitic phase at room temperature has been analyzed by neutron and high-resolution X-ray diffraction. The ball milling promotes a mechanically-induced martensitic transformation as well as the appearance of amorphous-like non-transforming regions, following a double stage; for short milling times (below 30 min), a strong size reduction and martensite induction occur. On the opposite, for longer times, the increase of strains predominates and consequently a larger amount of non-transforming regions appears. The effect of the microstructural defects brought by milling (as dislocations) on both the enthalpy change at the martensitic transformation and the high field magnetization of the austenite has been quantitatively estimated and correlated to the internal strains. Contrary to what occurs in ternary Ni-Mn-Sn alloys, the mechanically-induced defects do not change the ferromagnetic coupling between Mn atoms, but just cause a net reduction on the magnetic moments.
Open Access
Study of the martensitic transition in Ni-Mn-Sn-Ti ferromagnetic shape memory alloys
(Rede Latino-Americana de Materiais, 2018) Bonifacich, Federico Guillermo; Lambri, Osvaldo Agustín; Pérez de Landazábal Berganzo, José Ignacio; Recarte Callado, Vicente; Sánchez-Alarcos Gómez, Vicente; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In the present work, mechanical spectroscopy measurements as a function of temperature and strain have been performed in (at.%) Ni50Mn37Sn13-xTix (x=0, 0.5 and 2) ferromagnetic shape memory alloys in order both to study martensitic transition phenomenon and also to determine its temperature of appearance. For mechanical spectroscopy measurements, a five elements piezoelectric device recently developed has been used. In addition, other characterization techniques as, differential thermal analysis and superconducting quantum interference magnetic spectroscopy, were also used. Besides, relaxation processes near the martensitic transition temperature have been also observed.
Open Access
Martensitic transformation controlled by electromagnetic field: from experimental evidence to wireless actuator applications
(Elsevier, 2022) Garayo Urabayen, Eneko; La Roca, Paulo Matías; Gómez Polo, Cristina; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Gobierno de Navarra / Nafarroako Gobernua
Mechanical actuators based on shape memory alloys (SMA) are becoming a key component in the development of novel soft robotic applications and surgically implantable devices. Their working principle relies in the temperature induced martensitic transformation (MT), which is responsible of the actuation mechanism. In this work, we found experimental evidence to show that the martensitic transformation can be controlled by electromagnetic field (EF) by a wireless process in ferromagnetic shape memory alloys. It is shown that the martensitic transformation can be driven by an external EF (frequency 45 kHz) while the specific absorption rate (SAR), which was determined through real-time dynamic magnetization measurements, allows the instantaneous monitoring of the transformation evolution. On the basis of the obtained results, we propose a strategy to achieve a battery-free wireless SMA actuator that can be remotely controlled. This concept can be applicable to other SMA material that exhibit a similar magneto-structural phase transition
Open Access
Experimental observation of vacancy-assisted martensitic transformation shift in Ni-Fe-Ga alloys
(American Physical Society, 2019) Unzueta, Iraultza; Alonso de Robador Lorente, Daniel; Cesari, Eduard; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; García, José Ángel; Plazaola, Fernando; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
Positron annihilation lifetime spectroscopy is used to experimentally demonstrate the direct relationship between vacancies and the shift of the martensitic transformation temperature in a Ni55Fel7Ga28 alloy. The evolution of vacancies assisting the ordering enables shifts of the martensitic transformation up to 50 K. Our results confirm the role that both vacancy concentration and different vacancy dynamics play in samples quenched from the L2(1) and B2 phases, which dictate the martensitic transformation temperature and its subsequent evolution. Finally, by electron-positron density functional calculations V-Ni is identified as the most probable vacancy present in Ni55Fe17Ga28. This work evidences the capability of vacancies for the fine-tuning of the martensitic transformation temperature, paving the way for defect engineering of multifunctional properties.
Open Access
119Sn Mössbauer spectroscopy for assessing the local stress and defect state towards the tuning of Ni-Mn-Sn alloys
(AIP Publishing, 2017) Unzueta, Iraultza; López García, Javier; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física
The influence of defects and local stresses on the magnetic properties and martensitic transformation in Ni50Mn35Sn15 is studied at macroscopic and atomic scale levels. We show that both the structural and magnetic properties of the alloy are very sensitive to slight microstructural distortions. Even though no atomic disorder is induced by milling, the antiphase boundaries linked to dislocations promote the antiferromagnetic coupling of Mn, resulting in a significant decrease in the saturation magnetization. On the other hand, the temperature range of the transformation is considerably affected by the mechanically induced local stresses, which in turn does not affect the equilibrium temperature between the austenitic and martensitic phases. Finally, we demonstrate that the recovery of the martensitic transformation is directly related to the intensity of the non-magnetic component revealed by 119Sn Mössbauer spectroscopy. This result opens the possibility of quantifying the whole contribution of defects and the local stresses on the martensitic transformation in Ni-Mn-Sn alloys.