Open Access
Routes for enhanced magnetism in Ni-Mn-In metamagnetic shape memory alloys
(Elsevier, 2019) López García, Javier; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Fabelo, O.; Cesari, Eduard; Rodríguez Velamazán, José Alberto; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The authors provide in-depth physical insight into the enhancement of the magnetic properties of metamagnetic shape memory alloys produced by thermal treatment and cobalt doping. They use neutron scattering to study the atomic order and magnetic structures in the austenitic phases of Ni50Mn34In16 and Ni45Co5Mn37In13 alloys in two different states induced by thermal treatments. The increase of the magnetization in the austenite phase, particularly by cobalt doping, is explained by the enhanced ferromagnetic coupling between the magnetic moments located in octahedral sites. The spin density maps obtained from polarized neutron diffraction reveal the magnetic interaction pathways responsible for this coupling scheme.
Open Access
Magnetocaloric effect enhancement driven by intrinsic defects in a Ni45Co5Mn35Sn15 alloy
(Elsevier, 2019) Sánchez-Alarcos Gómez, Vicente; López García, Javier; Unzueta, Iraultza; Pérez de Landazábal Berganzo, José Ignacio; Recarte Callado, Vicente; Beato López, Juan Jesús; García, José Ángel; Plazaola, Fernando; Rodríguez Velamazán, José Alberto; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física
The influence of mechanically-induced defects on the magnetostructural properties is analyzed in a Ni-Co-Mn-Sn alloy subjected to soft milling and subsequent annealing treatments. It is found that, opposite to what occurs in Ni-Mn-Sn ternary alloys, the annealing treatment affects the magnetic properties in a different way in martensite and in austenite. In particular, the saturation magnetization significantly increases in martensite after annealing whereas just a very slight variation is observed in austenite. This leads to the interesting fact that the presence of microstructural defects, far for worsening, makes the magnetocaloric effect to be higher in the as-milled state than after annealing. This behavior is explained as the result of the combination of the effect of defects on the Mn-Mn distance, the effect of Co on the magnetic exchange coupling between Mn atoms, and the effect of defects on the vibrational entropy change at the martensitic transformation.
Open Access
Influence of defects on the irreversible phase transition in the Fe-Pd doped with Co and Mn
(Rede Latino-Americana de Materiais, 2018) Bonifacich, Federico Guillermo; Lambri, Osvaldo Agustín; Pérez de Landazábal Berganzo, José Ignacio; Recarte Callado, Vicente; Sánchez-Alarcos Gómez, Vicente; Fisika; Institute for Advanced Materials and Mathematics - INAMAT2; Física; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The appearance of BCT martensite in Fe-Pd-based ferromagnetic shape memory alloys, which develops at lower temperatures than the thermoelastic martensitic transition, deteriorates the shape memory properties. In a previous work performed in Fe70Pd30, it was shown that a reduction in defects density reduces the non thermoelastic FCT-BCT transformation temperature. In the present work, the influence of quenched-in-defects upon the intensity and temperature of the thermoelastic martensitic (FCC-FCT) and the non thermoelastic (FCT-BCT) transitions in Fe-Pd doped with Co and Mn is studied. Differential scanning calorimetric and mechanical spectroscopy studies demonstrate that a reduction in the dislocation density the stability range of the FCC-FCT reversible transformation in Fe67Pd30Co3 and Fe66.8Pd30.7Mn2.5 ferromagnetic shape memory alloys.
Open Access
Influence of structural defects on the properties of metamagnetic shape memory alloys
(MDPI, 2020) Pérez de Landazábal Berganzo, José Ignacio; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Lambri, Osvaldo Agustín; López García, Javier; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
The production of µ-particles of Metamagnetic Shape Memory Alloys by crushing and subsequent ball milling process has been analyzed. The high energy involved in the milling process induces large internal stresses and high density of defects with a strong influence on the martensitic transformation; the interphase creation and its movement during the martensitic transformation produces frictional contributions to the entropy change (exothermic process) both during forward and reverse transformation. The frictional contribution increases with the milling time as a consequence of the interaction between defects and interphases. The influence of the frictional terms on the magnetocaloric effect has been evidenced. Besides, the presence of antiphase boundaries linked to superdislocations helps to understand the spin-glass behavior at low temperatures in martensite. Finally, the particles in the deformed state were introduced in a photosensitive polymer. The mechanical damping associated to the Martensitic Transformation (MT) of the particles is clearly distinguished in the produced composite, which could be interesting for the development of magnetically-tunable mechanical dampers.
Open Access
Long-range atomic order and entropy change at the martensitic transformation in a Ni-Mn-In-Co metamagnetic shape memory alloy
(MDPI, 2014) Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Cesari, Eduard; Rodríguez Velamazán, José Alberto; Física; Fisika
The influence of the atomic order on the martensitic transformation entropy change has been studied in a Ni-Mn-In-Co metamagnetic shape memory alloy through the evolution of the transformation temperatures under high-temperature quenching and post-quench annealing thermal treatments. It is confirmed that the entropy change evolves as a consequence of the variations on the degree of L21 atomic order brought by thermal treatments, though, contrary to what occurs in ternary Ni-Mn-In, post-quench aging appears to be the most effective way to modify the transformation entropy in Ni-Mn-In-Co. It is also shown that any entropy change value between around 40 and 5 J/kgK can be achieved in a controllable way for a single alloy under the appropriate aging treatment, thus bringing out the possibility of properly tune the magnetocaloric effect.
Open Access
Effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy
(Elsevier, 2021) López García, José Luis; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Rodríguez Velamazán, José Alberto; Unzueta, Iraultza; García, José Ángel; Plazaola, Fernando; La Roca, Paulo Matías; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Gobierno de Navarra / Nafarroako Gobernua, PC017-018 AMELEC
The effect of high-energy ball-milling on the magnetostructural properties of a Ni45Co5Mn35Sn15 alloy in austenitic phase at room temperature has been analyzed by neutron and high-resolution X-ray diffraction. The ball milling promotes a mechanically-induced martensitic transformation as well as the appearance of amorphous-like non-transforming regions, following a double stage; for short milling times (below 30 min), a strong size reduction and martensite induction occur. On the opposite, for longer times, the increase of strains predominates and consequently a larger amount of non-transforming regions appears. The effect of the microstructural defects brought by milling (as dislocations) on both the enthalpy change at the martensitic transformation and the high field magnetization of the austenite has been quantitatively estimated and correlated to the internal strains. Contrary to what occurs in ternary Ni-Mn-Sn alloys, the mechanically-induced defects do not change the ferromagnetic coupling between Mn atoms, but just cause a net reduction on the magnetic moments.
Open Access
Polycaprolactone/MSMA composites for magnetic refrigeration applications
(Wiley, 2024-09-06) Sánchez-Alarcos Gómez, Vicente; Khanna, Deepali; La Roca, Paulo Matías; Recarte Callado, Vicente; Lambri, Fernando Daniel; Bonifacich, Federico Guillermo; Lambri, Osvaldo Agustín; Royo Silvestre, Isaac; Urbina Yeregui, Antonio; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
A high filling load (62% weight) printable magnetic composite has been elaborated from the dispersion of magnetocaloric Ni45Mn36.7In13.3Co5 metamagnetic shape memory alloy microparticles into a PCL polymer matrix. The composite material has been prepared by solution method, resulting in a very homogeneous particles dispersion into the matrix. The structural transitions in the polymer are not affected by the addition of the metallic microparticles, which in turn results in a significant increase of the mechanical consistency. The good ductility of the elaborated composite allows its extrusion in flexible printable filaments, from which 3D pieces with complex geometries have been grown. The heat transfer of the composite material has been assessed from finite element simulation. In spite of the achievable magnetocaloric values are moderated with respect to the bulk, numerical simulations confirm that, in terms of heat transference, a PCL/Ni-Mn-In-Co wire is more efficient than a bulk Ni-Mn-In-Co cubic piece containing the same amount of magnetic active material. The quite good magnetocaloric response of the composite and the possibility to print high surface/volume ratio geometries make this material a promising candidate for the development of heat exchangers for clean and efficient magnetic refrigeration applications.
Open Access
Experimental observation of vacancy-assisted martensitic transformation shift in Ni-Fe-Ga alloys
(American Physical Society, 2019) Unzueta, Iraultza; Alonso de Robador Lorente, Daniel; Cesari, Eduard; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Pérez de Landazábal Berganzo, José Ignacio; García, José Ángel; Plazaola, Fernando; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias
Positron annihilation lifetime spectroscopy is used to experimentally demonstrate the direct relationship between vacancies and the shift of the martensitic transformation temperature in a Ni55Fel7Ga28 alloy. The evolution of vacancies assisting the ordering enables shifts of the martensitic transformation up to 50 K. Our results confirm the role that both vacancy concentration and different vacancy dynamics play in samples quenched from the L2(1) and B2 phases, which dictate the martensitic transformation temperature and its subsequent evolution. Finally, by electron-positron density functional calculations V-Ni is identified as the most probable vacancy present in Ni55Fe17Ga28. This work evidences the capability of vacancies for the fine-tuning of the martensitic transformation temperature, paving the way for defect engineering of multifunctional properties.
Open Access
Monitoring structural transformations in metamagnetic shape memory alloys by non-contact GMI technology
(IOP Publishing, 2023) Beato López, Juan Jesús; La Roca, Paulo Matías; Algueta-Miguel, Jose M.; Garayo Urabayen, Eneko; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Different applications based on metamagnetic shape memory alloy (MSMA) require monitoring the evolution of the martensitic transformation (MT) to optimize the actuation mechanism. To avoid interaction with the active material, a non-contact technique would be ideal. Nevertheless, non-contact detection involves complex methods like diffraction, optical analysis, or electromagnetic technology. The present work demonstrates that the MT can be monitored without interaction with the active material using a low-cost technology based on the Giant Magnetoimpedance (GMI) effect. The GMI sensor is based on a (CoFe)SiB soft magnetic wire submitted to an alternating current and whose second harmonic voltage variation allows to detect changes in the strength of the stray magnetic fields linked to the metamagnetic phase transition. The sensor has been tested using the MT of a NiMnInCo MSMA. A specific application for environmental temperature control using the non-contact GMI sensor is proposed.
Open Access
Magnetically tunable damping in composites for 4D printing
(Elsevier, 2021) Bonifacich, Federico Guillermo; Lambri, Osvaldo Agustín; Recarte Callado, Vicente; Sánchez-Alarcos Gómez, Vicente; Pérez de Landazábal Berganzo, José Ignacio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Composite materials are being used in the design of new devices to produce more functional, cheap and on-demand products. In particular, 3D printing technology based on composites opens a huge field enabling the freedom of design and the ability to manufacture complex structures. In this context, the analysis of the functional properties of printable composites is of great importance. The work is focused on the analysis of the mechanical damping of a composite made with different concentrations of a Ni45Mn36.7In13.3Co5 metamagnetic shape memory alloy into an UV-curing polymer. The composites provide a bulk material containing very brittle metallic μ-particles that can be handled for technological applications. Damping and dynamic modulus of the composites were modified with small magnetic fields below 100 kA/m, proving that the damping capacity can be tuned by applying an external magnetic field. From the measurements, it has been also possible to determine the intrinsic damping and moduli of the alloy particles, which show the characteristic properties linked to the MT. These preliminary results allow proposing this composite material as a potential functional material to be used in the design of printable devices for magneto-mechanical damping applications.