Open Access
Random fiber lasers: application to fiber optic sensors networks
(IEEE, 2017) López-Amo Sáinz, Manuel; Leandro González, Daniel; Miguel Soto, Verónica de; Bravo Acha, Mikel; Fernández Vallejo, Montserrat; Pérez Herrera, Rosa Ana; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
Recently, random mirrors have been proposed as a method to create fiber laser cavities. This kind of cavity is based on cooperative Rayleigh scattering, which is generated along a fiber due to the material inhomogeneities presented in that fiber. In this work, basics of Random fiber lasers and different demonstrated lasing sensors systems for interrogating arrays of optical fiber sensors are shown. These systems use different kinds of amplification and cavities schemes and can interrogate optical fiber sensors located up to 225 km away.
Open Access
Random DFB fiber laser for remote (200 km) sensor monitoring using hybrid WDM/TDM
(IEEE, 2016) Leandro González, Daniel; Miguel Soto, Verónica de; Pérez Herrera, Rosa Ana; Bravo Acha, Mikel; López-Amo Sáinz, Manuel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, a random distributed feedback fiber laser is proposed as a multiplexing scheme for ultralong range measurements (up to 200 km). Optical fiber sensors are time and wavelength multiplexed overcoming one of the main limitations of long-range sensing setups, which is their limited multiplexing capability. The direct modulation of the laser's cavity allows the interrogation of sensors by measuring the reflected power for different wavelengths and distances. Fiber Bragg gratings placed at different fiber locations and wavelengths have been interrogated in two different sensor networks. In addition, in order to improve the performance of the system, some features have been analyzed.
Open Access
Multiparameter sensor based on a multiinterferometric serial configuration for temperature and strain measurements
(IEEE, 2021) Pérez Herrera, Rosa Ana; Bravo Acha, Mikel; Leandro González, Daniel; Novais, Susana; Pradas Martínez, Javier; López-Amo Sáinz, Manuel; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, a multi-parameter point sensor based on the combination of Fabry-Perot (FP) and the anti-resonant (AR) reflecting guidance in cascade configuration is proposed and experimentally demonstrated. This structure, based on FP interference and AR reflecting guidance, was fabricated with two different air micro-cavities. The attained experimental results showed different strain and temperature sensitivities for the antiresonance contribution. However, when analyzing the FP interference, only strain sensitivity was observed, demonstrating that this air micro-cavity was also insensitive to temperature variations.
Open Access
Power over fiber system for heterogeneous sensors multiplexing
(IEEE, 2024-06-12) Rodríguez Rodríguez, Armando; Vanegas Tenezaca, Evelyn Dayanara; Vento Álvarez, José Raúl; López-Amo Sáinz, Manuel; Bravo Acha, Mikel; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Uniertsitate Publikoa
This paper presents a Power-over-Fiber based remote electronic and optical fiber sensors multiplexing scheme. The system architecture consists of a 50-km linear cavity Raman-fiber laser that is used for interrogation of FBG optical fiber sensors. Simultaneously, electronic sensors information is modulated in amplitude while the optical sensors' data are encoded in the spectral information. In order to bias the electronic sensors, the residual power of the Raman pump laser is collected in an energy harvesting unit. This electric power is used for biasing an ATTiny85 control unit and two electro-optical modulators. A proof-of-concept is presented where a couple of optical fiber-Bragg-gratings sensors collect strain information that is self-compensated in temperature according to the digital data achieved from the electronic sensors. A 9.6 kbit/s data rate was achieved using Mach-Zehnder amplitude modulators and a maximum 35 ksample/s was retrieved using a high-speed C-band spectrometer and performing spectral analysis via a software developed in Python. Authors
Open Access
Real-time FFT analysis for interferometric sensors multiplexing
(IEEE / OSA, 2015) Leandro González, Daniel; Bravo Acha, Mikel; Ortigosa Cayetano, Amaia; López-Amo Sáinz, Manuel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, a theoretical and experimental study of two interferometric sensor multiplexing schemes has been carried out by means of the fast Fourier transform (FFT) analysis. This work addresses one of the main drawbacks of photonic crystal fiber (PCF) sensors, that is, its multiplexing capability. Using a commercial optical interrogator combined with a simple FFT measurement technique, the simultaneous real-time monitoring of several PCF sensors is achieved. A theoretical analysis has been performed where simulations matched with the experimental results. For the experimental verification, highly birefringent (HiBi) fiber sections that operated as sensing elements were multiplexed and tested in two configurations. Due to the FFT analysis, both multiplexing schemes can be properly interrogated by monitoring the FFT phase change at the characteristic spatial-frequency of each sensor. For this purpose a commercial interrogator and a custom Matlab program were used for computing the FFT and for monitoring the FFT phase change in real-time (1 Hz).