Open Access
Detection of signals in MC-CDMA using a novel iterative block decision feedback equalizer
(IEEE, 2022) Bagadi, Kalapraveen; Ravikumar, Chinthaginjala V.; Sathish, K.; Alibakhshikenari, Mohammad; Virdee, Bal S.; Kouhalvandi, Lida; Olan Núñez, Karen N.; Pau, Giovanni; See, Chan H.; Dayoub, Iyad; Livreri, Patrizia; Aïssa, Sonia; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents a technique to mitigate multiple access interference (MAI) in multicarrier code division multiple access (MC-CDMA) wireless communications systems. Although under normal circumstances the MC-CDMA system can achieve high spectral efficiency and resistance towards inter symbol interference (ISI) however when exposed to substantial nonlinear distortion the issue of MAI manifests. Such distortion results when the power amplifiers are driven into saturation or when the transmit signal experiences extreme adverse channel conditions. The proposed technique uses a modified iterative block decision feedback equalizer (IB-DFE) that uses a minimal mean square error (MMSE) receiver in the feed-forward path to nullify the residual interference from the IB-DFE receiver. The received signal is re-filtered in an iterative process to significantly improve the MC-CDMA system's performance. The effectiveness of the proposed modified IB-DFE technique in MC-CDMA systems has been analysed under various harsh nonlinear conditions, and the results of this analysis presented here confirm the effectiveness of the proposed technique to outperform conventional methodologies in terms of the bit error rate (BER) and lesser computational complexity.
Open Access
Virtual antenna array for reduced energy per bit transmission at Sub-5 GHz mobile wireless communication systems
(Elsevier, 2023) Alibakhshikenari, Mohammad; Virdee, Bal S.; Mariyanayagam, Dion; García Zuazola, Ignacio Julio; Benetatos, Harry; Althuwayb, Ayman Abdulhadi; Alali, Bader; Xu, Kai-Da; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents an innovative technique to synthesize a virtual antenna array (VAA) that consumes less energy than conventional antenna arrays that are used in mobile communications systems. We have shown that for a specific spectral efficiency a wireless system using the proposed virtual antenna array consumes significantly less energy per bit (∼3 dB) than a wireless system using a conventional multiple-input multiple-output (MIMO) array. This means the adoption of the proposed VAA technology in smartphones, iPad, Tablets and even base-stations should significantly reduce the carbon footprint of wireless systems. The proposed VAA is realized by employing a pair of linear antenna arrays that are placed in an orthogonal configuration relative to each other. This orthogonal arrangement ensures the radiation is circularly polarized. The size of the standard radiating elements constituting the VAA were miniaturized using the topology optimization method. The design of the VAA incorporates substrate integrated waveguide (SIW) and metasurface technologies. The function of SIW in the design was twofold, namely, to reduce energy loss in the substrate on which the VAA is implemented, and secondly to mitigate unwanted electromagnetic interactions between the neighboring radiating elements and thereby enhancing isolation which otherwise would degrade the radiation characteristics of the array. Metasurface technology served to effectively increase the effective aperture of the array with no impact on the footprint of the array. The consequence of SIW and metasurface technologies was improvement in the gain and radiation efficiency of the array. The proposed four orthogonal 4-element VAA covers the entire sub-5 GHz frequency range, and it radiates bidirectional in the azimuth plane and omni-directional in the elevation plane. Moreover, it is relatively easy to design and fabricate. The proposed VAA has dimensions of 0.96λ0 × 0.96λ0 × 0.0016λ0 at mid-band frequency of 3 GHz. VAA has a measured gain of 25 dBi and radiates with 90% efficiency. The average isolation between the linear arrays constituting the virtual array is better than 27 dB.
Open Access
Electronically reconfigurable and conformal triband antenna for wireless communications systems and portable devices
(Public Library of Science, 2022) Hussain, Musa; Ali, Esraa Mousa; Awan, Wahaj Abbas; Hussain, Niamat; Alibakhshikenari, Mohammad; Virdee, Bal S.; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents the design of a triband antenna that can be electronically configured to operate at different frequencies. The proposed antenna is design to operate at sub-6GHz bands at 2.45 GHz (ISM, Wi-Fi, and WLAN), 3.3, 3.5 & 3.9 GHz (WiMAX), and 4.1 & 4.9 GHz (4G & 5G). This is achieved by connecting two open-ended stubs to a modified triangular patch radiator using PIN diodes. The antenna’s performance was optimized using a 3D electromagnetic solver and its performance was verified through measurements. Moreover, the conformal analysis done on the antenna shows that the proposed technique can be used in moderately flexible wireless devices without compromising the antenna’s gain, radiation efficiency and radiation patterns. These characteristics makes the proposed antenna applicable for various wireless communication systems and devices.
Open Access
High-isolation antenna array using SIW and realized with a graphene layer for sub-terahertz wireless applications
(Nature Research, 2021) Alibakhshikenari, Mohammad; Virdee, Bal S.; Salekzamankhani, Shahram; Aïssa, Sonia; See, Chan H.; Soin, Navneet; Fishlock, Sam J.; Althuwayb, Ayman Abdulhadi; Abd-Alhameed, Raed; Huynen, Isabelle; McLaughlin, James A.; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This paper presents the results of a study on developing an effective technique to increase the performance characteristics of antenna arrays for sub-THz integrated circuit applications. This is essential to compensate the limited power available from sub-THz sources. Although conventional array structures can provide a solution to enhance the radiation-gain performance however in the case of small-sized array structures the radiation properties can be adversely affected by mutual coupling that exists between the radiating elements. It is demonstrated here the effectiveness of using SIW technology to suppress surface wave propagations and near field mutual coupling effects. Prototype of 2x3 antenna arrays were designed and constructed on a polyimide dielectric substrate with thickness of 125 mu m for operation across 0.19-0.20 THz. The dimensions of the array were 20x13.5x0.125 mm(3). Metallization of the antenna was coated with 500 nm layer of Graphene. With the proposed technique the isolation between the radiating elements was improved on average by 22.5 dB compared to a reference array antenna with no SIW isolation. The performance of the array was enhanced by transforming the patch to exhibit metamaterial characteristics. This was achieved by embedding the patch antennas in the array with sub-wavelength slots. Compared to the reference array the metamaterial inspired structure exhibits improvement in isolation, radiation gain and efficiency on average by 28 dB, 6.3 dBi, and 34%, respectively. These results show the viability of proposed approach in developing antenna arrays for application in sub-THz integrated circuits.
Open Access
Review on unmanned aerial vehicle assisted sensor node localization in wireless networks: soft computing approaches
(IEEE, 2022) Annepu, Visalakshi; Sona, Deepika Rani; Ravikumar, Chinthaginjala V.; Bagadi, Kalapraveen; Alibakhshikenari, Mohammad; Althuwayb, Ayman Abdulhadi; Alali, Bader; Virdee, Bal S.; Pau, Giovanni; Dayoub, Iyad; See, Chan H.; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Node positioning or localization is a critical requisite for numerous position-based applications of wireless sensor network (WSN). Localization using the unmanned aerial vehicle (UAV) is preferred over localization using fixed terrestrial anchor node (FTAN) because of low implementation complexity and high accuracy. The conventional multilateration technique estimates the position of the unknown node (UN) based on the distance from the anchor node (AN) to UN that is obtained from the received signal strength (RSS) measurement. However, distortions in the propagation medium may yield incorrect distance measurement and as a result, the accuracy of RSS-multilateration is limited. Though the optimization based localization schemes are considered to be a better alternative, the performance of these schemes is not satisfactory if the distortions are non-linear. In such situations, the neural network (NN) architecture such as extreme learning machine (ELM) can be a better choice as it is a highly non-linear classifier. The ELM is even superior over its counterpart NN classifiers like multilayer perceptron (MLP) and radial basis function (RBF) due to its fast and strong learning ability. Thus, this paper provides a comparative review of various soft computing based localization techniques using both FTAN and aerial ANs for better acceptability.
Open Access
An antenna array utilizing slotted conductive slab: inspired by metasurface and defected ground plane techniques for flexible electronics and sensors operating in the millimeter-wave and terahertz spectrum
(Springer, 2023) Ali, Esraa Mousa; Alibakhshikenari, Mohammad; Virdee, Bal S.; Kouhalvandi, Lida; Livreri, Patrizia; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper describes an innovative design of an antenna array that is metamaterial inspired using sub-wavelength slots and defected ground structure (DGS) for operation over millimeter-wave and terahertz (THz) spectrum. The proposed antenna array consists of a 2 × 4 array of conductive boxes on which are implemented rectangular slots. The presence of dielectric slots introduces resonant modes within the structure. These resonant modes result in enhancing the electromagnetic fields within the slots, which radiate energy into free space. The resonant frequencies and radiation patterns depend on the specific geometry of the slots and the dielectric properties. The antenna array is excited through a single microstrip line. The radiating elements in the array are interconnected to each other with a microstrip line. Unwanted mutual coupling between the radiating elements can degrade the performance of the antenna. This was mitigated by defecting the ground plane with rectangular slots. It is shown that this technique can enhance the array¿s reflection coefficient over a wider bandwidth. The array was constructed on polyimide substrate having dielectric constant of 3.5 and thickness of 20 ¿m. The design was modelled, and its performance verified using an industry standard electromagnetic package by CST Studio Suite. The proposed array antenna has dimensions of 20 × 10 mm2 and operates between 80 and 200 GHz for radiation gain better than 4 dBi and efficiency above 55%. The peak radiation gain and efficiency are 7.5 dBi and 75% at 91 GHz, respectively. The operational frequency range of the array corresponds to a fractional bandwidth of 85.71%.
Open Access
Optical-microwave sensor for real-time measurement of water contamination in oil derivatives
(Elsevier, 2023) Abdulsattar, Rusul K.; Alibakhshikenari, Mohammad; Virdee, Bal S.; Sharma, Richa; Elwi, Taha A.; Kouhalvandi, Lida; Hassain, Zaid Abdul; Ali, Syed Mansoor; Türker Tokan, Nurhan; Livreri, Patrizia; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
This paper presents a novel microwave sensor using optical activation for measuring in real-time the water contamination in crude oil or its derivatives. The sensor is constructed from an end-coupled microstrip resonator that is interconnected to two pairs of identical fractal structures based on Moore curves. Electromagnetic (EM) interaction between the fractal curves is mitigated using a T-shaped microstrip-stub to enhance the performance of the sensor. The gap in one pair of fractal curves is loaded with light dependent resistors (LDR) and the other pair with microwave chip capacitors. The chip capacitors were used to increase the EM coupling between the fractal gaps to realize a high Q-factor resonator that determines the sensitivity of the sensor. Empirical results presented here show that the insertion-loss of the sensor is affected by the change in LDR impedance when illuminated by light. This property is used to determine the amount of water contaminated oil. The sensitivity of the sensor was optimized using commercial 3D EM solver. The measurements were made by placing a 30 mm diameter petri dish holding the sample on top of the sensor. The petri dish was filled up to a height of 10 mm with the sample of water contaminated crude oil, and the measurements were done in the range between 0.76 GHz and 1.2 GHz. The Q-factor of the oil sample with no water contamination was 70 and the Q-factor declined to 20 for 100% contamination. The error in the measurements was less than 0.024%. The sensor has dimensions of 0.127λo × 0.127λo × 0.004 λo and represents a new modality. Compared to existing techniques, the proposed sensor is simple to use, readily portable and is more sensitive.
Open Access
Optimum power transfer in RF front end systems using adaptive impedance matching technique
(Nature Research, 2021) Alibakhshikenari, Mohammad; Virdee, Bal S.; Azpilicueta Fernández de las Heras, Leyre; See, Chan H.; Abd-Alhameed, Raed; Althuwayb, Ayman Abdulhadi; Falcone Lanas, Francisco; Huynen, Isabelle; Denidni, Tayeb A.; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Matching the antenna’s impedance to the RF-front-end of a wireless communications system is challenging as the impedance varies with its surround environment. Autonomously matching the antenna to the RF-front-end is therefore essential to optimize power transfer and thereby maintain the antenna’s radiation efficiency. This paper presents a theoretical technique for automatically tuning an LC impedance matching network that compensates antenna mismatch presented to the RF-front-end. The proposed technique converges to a matching point without the need of complex mathematical modelling of the system comprising of non-linear control elements. Digital circuitry is used to implement the required matching circuit. Reliable convergence is achieved within the tuning range of the LC-network using control-loops that can independently control the LC impedance. An algorithm based on the proposed technique was used to verify its effectiveness with various antenna loads. Mismatch error of the technique is less than 0.2%. The technique enables speedy convergence (< 5 µs) and is highly accurate for autonomous adaptive antenna matching networks.
Open Access
Impedance bandwidth improvement of a planar antenna based on metamaterial-inspired T-matching network
(IEEE, 2021) Alibakhshikenari, Mohammad; Virdee, Bal S.; Shukla, Panchamkumar; Wang, Yan; Azpilicueta Fernández de las Heras, Leyre; Naser Moghadasi, Mohammad; See, Chan H.; Elfergani, Issa; Zebiri, Chemseddine; Abd-Alhameed, Raed; Huynen, Isabelle; Rodriguez, Jonathan; Denidni, Tayeb A.; Falcone Lanas, Francisco; Limiti, Ernesto; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this paper a metamaterial-inspired T-matching network is directly imbedded inside the feedline of a microstrip antenna to realize optimum power transfer between the front-end of an RF Wireless transceiver and the antenna. The proposed T-matching network, which is composed of an arrangement of series capacitor, shunt inductor, series capacitor, exhibits left-handed metamaterial characteristics. The matching network is first theoretically modelled to gain insight of its limitations. It was then implemented directly in the 50-Ω feedline to a standard circular patch antenna, which is an unconventional methodology. The antenna’s performance was verified through measurements. With the proposed technique there is 2.7 dBi improvement in the antenna’s radiation gain and 12% increase in the efficiency at the center frequency,and this is achieved over a significantly wider frequency range by a factor of approximately twenty. Moreover, there is good correlation between the theoretical model, method of moments simulation, and the measurement results.
Open Access
Metamaterial inspired electromagnetic bandgap filter for ultra-wide stopband screening devices of electromagnetic interference
(Springer, 2023) Al-Hasan, Muath; Alibakhshikenari, Mohammad; Virdee, Bal S.; Sharma, Richa; Iqbal, Amjad; Althuwayb, Ayman Abdulhadi; Falcone Lanas, Francisco; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Presented here is a reactively loaded microstrip transmission line that exhibit an ultra-wide bandgap. The reactive loading is periodically distributed along the transmission line, which is electromagnetically coupled. The reactive load consists of a circular shaped patch which is converted to a metamaterial structure by embedded on it two concentric slit-rings. The patch is connected to the ground plane with a via-hole. The resulting structure exhibits electromagnetic bandgap (EBG) properties. The size and gap between the slit-rings dictate the magnitude of the reactive loading. The structure was frst theoretically modelled to gain insight of the characterizing parameters. The equivalent circuit was verifed using a full-wave 3D electromagnetic (EM) solver. The measured results show the proposed EBG structure has a highly sharp 3-dB skirt and a very wide bandgap, which is substantially larger than any EBG structure reported to date. The bandgap rejection of the single EBG unit-cell is better than − 30 dB, and the fve element EBG unit-cell is better than − 90 dB. The innovation can be used in various applications such as biomedical applications that are requiring sharp roll-of rates and high stopband rejection thus enabling efcient use of the EM spectrum. This can reduce guard band and thereby increase the channel capacity of wireless systems.