Open Access
A comparative study between SMS interferometers and lossy mode resonace optical fiber devices for sensing applications
(SPIE, 2015) Socorro Leránoz, Abián Bentor; Hernáez Sáenz de Zaitigui, Miguel; Del Villar, Ignacio; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Optical fiber sensors are of great interest due to their intrinsic advantages over electronic sensors. In this work, the sensing characteristics of two different and novel optical fiber devices are compared, after simultaneously depositing a thin-film using the layer-by-layer assembly deposition process. The first one is an SMS structure, formed by splicing two single-mode fiber pigtails on both sides of a coreless multimode fiber segment. This structure induces an interferometric phenomenon that generates several attenuation and transmission bands along the spectrum. These bands are sensitive to variations in the surrounding refractive index, although this sensitivity has been enhanced by a TiO2/PSS thin-film. The other device is a 40 mm uncladded segment of a 200 µm-core multimode optical fiber. When coated by a TiO2/PSS thinfilm, part of the light transmitted into the uncladded core is coupled into the thin-film, generating a lossy mode resonance (LMR). The absorption peaks due to these phenomena red-shift as long as the thin-film thickness increases or the external RI becomes higher. The performance of these devices as refractometers and relative humidity sensors are tested. Results show that the LMR-based sensor is more sensitive in both situations, in spite of its lower sensitivity. Particularly, it presents a 7-fold sensitivity enhancement when measuring surrounding medium refractive index changes and a 10-fold sensitivity enhancement when measuring environmental relative humidity. To our knowledge, this is the first time that a comparative study between SMS and LMR sensors is performed.
Open Access
Humidity sensor based on Bragg gratings developed on the end facet of an optical fiber by sputtering of one single material
(MDPI, 2017) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The refractive index of sputtered indium oxide nanocoatings has been altered just by changing the sputtering parameters, such as pressure. These induced changes have been exploited for the generation of a grating on the end facet of an optical fiber towards the development of wavelength-modulated optical fiber humidity sensors. A theoretical analysis has also been performed in order to study the different parameters involved in the fabrication of this optical structure and how they would affect the sensitivity of these devices. Experimental and theoretical results are in good agreement. A sensitivity of 150 pm/%RH was obtained for relative humidity changes from 20% to 60%. This kind of humidity sensors shows a maximum hysteresis of 1.3% relative humidity.
Open Access
AC/DC millivoltage sensor by means of ITO-coated optical fibers: towards monitoring of biosignals
(IEEE, 2019) Aginaga Etxamendi, Concepción Isabel; Socorro Leránoz, Abián Bentor; Fuentes Lorenzo, Omar; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
This contribution shows the monitoring of AC and DC millivoltage signals by means of lossy mode resonances generated by Indium Tin Oxide (ITO) on optical fibers. Sensors were obtained by sputtering ITO thin-films onto 25 mm-length segments of 200 μm bare optical fibers. Depositing a 1 μm thin-film of ITO leads to obtain reduced thin-film resistances of near 340 ohms. This allows the detection of voltage signals by monitoring the wavelength shift of the resonances. Sensitivities up to 40 nm/V can be achieved when tracking sinusoidal signals of a few cents of mV peak-to-peak. This opens the path for further research pursuing the detection of biomedical signals.
Open Access
Spectral width reduction in lossy mode resonance-based sensors by means of tapered optical fibre structures
(Elsevier, 2014) Socorro Leránoz, Abián Bentor; Del Villar, Ignacio; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Open Access
Refractometric sensors based on multimode interference in a thin-film coated singlemode– multimode–single-mode structure with reflection configuration
(Optical Society of America, 2014) Del Villar, Ignacio; Socorro Leránoz, Abián Bentor; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
Thin-film coated single-mode–multimode–single-mode (SMS) structures have been analyzed both theoretically and experimentally with the aim of detecting different refractive indices. By adequate selection of the thickness of the thin film and of the diameter of the multimode segment in the SMS structure, a seven-fold improvement can be obtained in the sensitivity of the device to the surrounding medium refractive index, achieving a maximum sensitivity of 1199.18 nm∕refractive index unit for the range of refractive indices from 1.321 to 1.382. Using layer-by-layer self-assembly for deposition, both on the cladding and on the tip of the multimode segment, allows the reflected power to increase, which avoids the application of a mirror on the tip of the multimode segment.
Open Access
Mode transition in complex refractive index coated single-mode–multimode–single-mode structure
(Optical Society of America, 2013) Socorro Leránoz, Abián Bentor; Del Villar, Ignacio; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
By coating a single-mode–multimode–single-mode (SMS) structure with a high refractive index thin-film it is possible to obtain a transition of modes for specific combinations of thin-film thickness, thinfilm refractive index and surrounding medium refractive index, which permits to develop devices with a high sensitivity to specific parameters. In order to gain a better knowledge of the phenomenon the experimental results are corroborated numerically with the Transfer-Matrix-Method. The influence of losses in the thin-film has also been studied. The results obtained prove that a thin-film coated SMS structure is a simple and costeffective platform for development of sensors and optical filters.
Open Access
Fabrication of long period gratings by periodically removing the coating of cladding-etched single mode optical fiber towards optical fiber sensor development
(MDPI, 2018) Ascorbe Muruzabal, Joaquín; Corres Sanz, Jesús María; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua, 2017/PI044
Here, we present a novel method to fabricate long period gratings using standard single mode optical fibers (SMF). These optical devices were fabricated in a three-step process, which consisted of etching the SMF, then coating it with a thin-film and, the final step, which involved removing sections of the coating periodically by laser ablation. Tin dioxide was chosen as the material for this study and it was sputtered using a pulsed DC sputtering system. Theoretical simulations were performed in order to select the appropriate parameters for the experiments. The responses of two different devices to different external refractive indices was studied, and the maximum sensitivity obtained was 6430 nm/RIU for external refractive indices ranging from 1.37 to 1.39.
Open Access
Monitoring the etching process in LPFGs towards development of highly sensitive sensors
(MDPI, 2017) Del Villar, Ignacio; Cruz, José Luis; Socorro Leránoz, Abián Bentor; Díaz Lucas, Silvia; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako Gobernua: 2016/PI008; Gobierno de Navarra / Nafarroako Gobernua: 2016/PC025; Gobierno de Navarra / Nafarroako Gobernua: 2016/PC026
In this work, the monitoring of the etching process up to a diameter of 30 µm of two LPFG structures has been compared, one of them had initially 125 µm, whereas the second one had 80 µm. By tracking the wavelength shift of the resonance bands during the etching process it is possible to check the quality of etching process (the 80 µm fibre performs better than de 125 µm fibre), and to stop for a specific cladding mode coupling, which permits to obtain an improved sensitivity compared to the initial structure.
Open Access
Sensitivity enhancement in low cutoff wavelength long-period fiber gratings by cladding diameter reduction
(MDPI, 2017) Del Villar, Ignacio; Partridge, Matthew; Rodríguez Rodríguez, Wenceslao Eduardo; Fuentes Lorenzo, Omar; Socorro Leránoz, Abián Bentor; Díaz Lucas, Silvia; Corres Sanz, Jesús María; James, Stephen; Tatam, Ralph; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako Gobernua: 2017/PI044
The diameter of long-period fiber gratings (LPFGs) fabricated in optical fibers with a low cutoff wavelength was be reduced by hydrofluoric acid etching, enhancing the sensitivity to refractive index by more than a factor of 3, to 2611 nm/refractive index unit in the range from 1.333 to 1.4278. The grating period selected for the LPFGs allowed access to the dispersion turning point at wavelengths close to the visible range of the optical spectrum, where optical equipment is less expensive. As an example of an application, a pH sensor based on the deposition of a polymeric coating was analyzed in two situations: with an LPFG without diameter reduction and with an LPFG with diameter reduction. Again, a sensitivity increase of a factor of near 3 was obtained, demonstrating the ability of this method to enhance the sensitivity of thin-film-coated LPFG chemical sensors.
Open Access
Etched LPFGs in reflective configuration for sensitivity and attenuation band depth increase
(IEEE, 2016) Del Villar, Ignacio; Socorro Leránoz, Abián Bentor; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Cruz, José Luis; Rego, Gaspar; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
A reflection configuration setup for long-period fiber gratings is presented. It permits to obtain a unique band with attenuation double than that obtained in transmission configuration, which is interesting for applications where this value is reduced (e.g., the mode transition phenomenon). The method is based on the deposition of a silver mirror at the end of the optical fiber, which permits to absorb the power transmitted through cladding modes and to avoid the generation of interferometric bands. The method also solves the requirement of a precise cleave or to polish the end of the grating, a drawback present in other publications. The versatility of the setup has been proved by application of the cladding etching technique until the attenuation band corresponding with the first guided mode in the cladding is visualized in an optical spectrum analyzer. The experimental results are supported by the numerical data obtained with a method based on the exact calculation of core and cladding modes and the utilization of coupled mode theory