Open Access
High frequency power transformers with foil windings: maximum interleaving and optimal design
(IEEE, 2015) Barrios Rípodas, Ernesto; Urtasun Erburu, Andoni; Ursúa Rubio, Alfredo; Marroyo Palomo, Luis; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Foil conductors and primary and secondary interleaving are normally used to minimize winding losses in high frequency transformers used for high-current power applications. However, winding interleaving complicates the transformer assembly, since taps are required to connect the winding sections, and also complicates the transformer design, since it introduces a new tradeoff between minimizing losses and reducing the construction difficulty. This paper presents a novel interleaving technique, named maximum interleaving, that makes it possible to minimize the winding losses as well as the construction difficulty. An analytical design methodology is also proposed in order to obtain free cooled transformers with a high efficiency, low volume and, therefore, a high power density. For the purpose of evaluating the advantages of the proposed maximum interleaving technique, the methodology is applied to design a transformer positioned in the 5 kW 50 kHz intermediate high frequency resonant stage of a commercial PV inverter. The proposed design achieves a transformer power density of 28 W/cm3 with an efficiency of 99.8%. Finally, a prototype of the maximum-interleaved transformer is assembled and validated satisfactorily through experimental tests.
Open Access
Dynamic modeling of a pressurized alkaline water electrolyzer: a multiphysics approach
(IEEE, 2023) Iribarren Zabalegui, Álvaro; Elizondo Martínez, David; Barrios Rípodas, Ernesto; Ibaiondo, Harkaitz; Sánchez Ruiz, Alain; Arza, Joseba; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper a dynamic model for the simulation of pressurized alkaline water electrolyzers is presented. The model has been developed following a multiphysics approach, integrating electrochemical, thermodynamic, heat transfer and gas evolution processes in order to faithfully reproduce the complete dynamical behavior of these systems. The model has been implemented on MATLAB/Simulink and validated through experimental data from a 1 Nm3/h commercial alkaline water electrolyzer. Validations have been performed under real scenarios where the electrolyzer is working with power profiles characteristic from renewable sources, wind and photovoltaic. The simulated results have been found to be consistent with the real measured values. This model has a great potential to predict the behavior of alkaline water electrolyzers coupled with renewable energy sources, making it a very useful tool for designing efficient green hydrogen production systems.
Open Access
Control design and stability analysis of power converters: the discrete generalized Bode criterion
(IEEE, 2021) Urtasun Erburu, Andoni; Samanes Pascual, Javier; Barrios Rípodas, Ernesto; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
For the controller design and stability analysis of power electronic converters, the Bode stability criterion and its subsequent revisions are the most practical tools. However, even though the control of the power converter is usually implemented in a microprocessor, none of these methods is infallible when applied to a discrete system. This article therefore proposes a new stability criterion, named the Discrete Generalized Bode Criterion (DGBC). This method is based on the Nyquist criterion but developed from the open-loop Bode diagram, evaluated also at 0 Hz and at the Nyquist frequency. The proposed criterion combines the advantages of the Nyquist and Bode criteria, since it is always applicable and provides an interesting and useful tool for the controller design process. The method is applied to design an active damping control of an inverter with LCL filter, showing how the proposed criterion accurately predicts stability, in contrast to the existing Bode criteria. The theoretical analysis is validated through experimental results performed with a three-phase inverter and an LCL filter.
Open Access
Novel three-phase topology for cascaded multilevel medium-voltage conversion systems in large-scale PV plants
(IEEE, 2020) Lumbreras Magallón, David; Barrios Rípodas, Ernesto; Balda Belzunegui, Julián; González Senosiain, Roberto; Sanchis Gúrpide, Pablo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Solar photovoltaic renewable energy systems are expanding in the power sector thanks to its increasingly competitive prices. Traditionally, large-scale PV plants have reduced their cost by increasing the power ratings of the inverters and the line-frequency transformers. However, cost-reduction limits of large-scale PV plants are being reached. Cascaded converters have appeared as a solution to continue reducing the cost of large PV plants as they reduce the wiring cost. In this paper, a novel three-phase topology for cascaded conversion structures is proposed. It only has 2 conversion steps, one without switching losses. Hence, it increases the efficiency and reduces the cost of the previously proposed cascaded conversion systems. The topology is patent pending.
Open Access
On the stability criteria for inverter current control loops with LCL output filters and varying grid impedance
(IEEE, 2017) Lumbreras Magallón, David; Barrios Rípodas, Ernesto; Ursúa Rubio, Alfredo; Marroyo Palomo, Luis; Sanchis Gúrpide, Pablo; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The use of LC and LCL filters and grid impedance variations are creating new challenges on the controller design for current control loops of photovoltaic and wind turbine inverters. In the design process, stability criteria such as Bode and revised Bode are commonly used. This paper analyses the limitations of Bode and revised Bode criteria to reliably determine stability and proposes a sufficient and necessary stability criterion, based on the Nyquist criterion, but that makes use of the Bode diagram. The proposed criterion, named generalized Bode criterion, is always reliable and helps the controller design. Relative stability in complex control loops is also studied and a relative stability analysis is proposed. Finally, the generalized Bode criterion and the proposed relative stability analysis are illustrated with a practical example in which a PI is designed in order to guarantee stability and achieve relative stability.
Open Access
Winding resistance measurement in power inductors - understanding the impact of the winding mutual resistance
(IEEE, 2021) Barrios Rípodas, Ernesto; Elizondo Martínez, David; Ursúa Rubio, Alfredo; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Inductors are cornerstone components in power electronics converters. Since winding loss is the dominant loss mechanism in these components, its accurate measurement is fundamental for the validation of the inductor's operation and design. The techniques for the winding resistance R_{w} measurement in power inductors can be classified into two groups, indirect and direct. Both techniques use coupled inductors to separate winding and core power losses. If coupled inductors with non-zero winding mutual resistances R_{w,m} are used, invalid results are obtained with these techniques. Understanding the meaning of R_{w,m} in coupled inductors is complex. In this paper, the impact of R_{w,m} on the inductor R_{w} measurement techniques is demonstrated and practical guidelines for the design of the zero R_{w,m} coupled inductors are given. Particularly, the location of the auxiliary winding for the direct technique is investigated. In order to compare the R_{w} measurement techniques and to validate the coupled inductor's R_{w,m} impact, two different inductors are built and tested. The results are compared with the values for R_{w} calculated by FEA simulation. It is found that only the direct technique with an auxiliary winding carefully designed and located following the guidelines given in this paper makes the accurate measurement of R_{w} in power inductors possible.
Open Access
Analytical modeling of high-frequency winding loss in round-wire toroidal inductors
(IEEE, 2023) Elizondo Martínez, David; Barrios Rípodas, Ernesto; Ursúa Rubio, Alfredo; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Toroidal inductors are used in many industrial applications in which they are key components regarding cost and volume. In the inductor design process, it is paramount to accurately estimate its high-frequency winding loss. Finite-element analysis (FEA) software and analytical models can be used for this purpose. However, the former employs too much time and the latter lacks accuracy when applied to toroidal windings, leading to an overestimation that can exceed 200%. As a consequence, designers would benefit from a reliable method to calculate high-frequency loss in toroidal windings. This article proposes an analytical model that considers the 2-D characteristic of the magnetic field and the geometrical particularities of toroidal windings. Furthermore, it provides an easy-to-use method, which avoids the unaffordable computational cost of FEA software. Simulations and experimental measurements are carried out for seven toroidal power inductors, from 10 Hz up to 200 kHz. Three different well-known state-of-the-art analytical models are used for comparison purposes. The results obtained with the proposed model are in good agreement with those from FEA and the experiments. The proposed model shows a maximum deviation below 20% while the overestimation of the existing analytical methods reaches values from 93% to 226%.
Open Access
Modelado y metodología analítica de diseño de transformadores de potencia y alta frecuencia: análisis de los devanados, optimización de eficiencia y densidad de potencia e integración en el diseño de convertidores electrónicos
(2015) Barrios Rípodas, Ernesto; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
Esta tesis se centra en el estudio y análisis del diseño de transformadores de potencia y alta frecuencia. Los principales temas tratados en esta tesis se resumen a continuación: - Realización del estado del arte y síntesis del modelado de transformadores de potencia y alta frecuencia, haciendo especial hincapié en el estudio de los materiales magnéticos, los fenómenos de alta frecuencia en los devanados, el cálculo de pérdidas en el núcleo y en el cobre y las técnicas que permiten su atenuación. - Tratamiento específico de formas de onda no senoidales de tensión y corriente. - Realización del estado del arte de los métodos de diseño existentes. Evaluación de la bondad de las reglas de oro, rules of thumb, en el diseño de transformadores. - Análisis teórico del problema de diseño y definición del concepto de diseño óptimo en términos de densidad de potencia y eficiencia para un rango de frecuencias de 1 a 150 kHz y de potencias de 500 W a 25 kW. - Desarrollo de una metodología analítica de diseño que conduce al diseño óptimo en términos de selección del material magnético, proporciones y tamaño del núcleo magnético, disposición de los devanados (reparto de ventana e intercalado), tipo de cable y su dimensionado, y nivel de inducción magnética. - Ejemplos de diseño: inversor fotovoltaico y convertidor forward. Realización de diseños prácticos y verificación experimental. Tratamiento de la problemática de la medida de pérdidas en estas aplicaciones. - Estudio de las tendencias presentes en la densidad de potencia y la eficiencia de los diseños óptimos en función de la potencia y la frecuencia de la aplicación. - Proposición de diversas fórmulas para posibilitar la integración del diseño de transformadores en el proceso de diseño y dimensionado de los convertidores electrónicos de potencia.
Open Access
Analytical design methodology for Litz-wired high-frequency power transformers
(IEEE, 2015) Barrios Rípodas, Ernesto; Ursúa Rubio, Alfredo; Marroyo Palomo, Luis; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In the last quarter of a century, high-frequency (HF) transformer design has been one of the major concerns to power electronics designers in order to increase converter power densities and efficiencies. Conventional design methodologies are based on iterative processes and rules of thumb founded more on expertise than on theoretical developments. This paper presents an analytical design methodology for litz-wired HF power transformers that provides a deep insight into the transformer design problem making it a powerful tool for converter designers. The most suitable models for the calculation of core and winding losses and the transformer thermal resistance are first selected and then validated with a 5-kW 50-kHz commercial transformer for a photovoltaic application. Based on these models, the design methodology is finally proposed, reducing the design issue to directly solve a five-variable nonlinear optimization problem. The methodology is illustrated with a detailed design in terms of magnetic material, core geometry, and primary and secondary litz-wire sizing. The optimal design achieves a 46.5% power density increase and a higher efficiency of 99.70% when compared with the commercial one.
Open Access
Dynamic modeling and simulation of a pressurized alkaline water electrolyzer: a multiphysics approach
(IEEE, 2021) Iribarren Zabalegui, Álvaro; Barrios Rípodas, Ernesto; Ibaiondo, Harkaitz; Sánchez Ruiz, Alain; Arza, Joseba; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this paper a dynamic model for the simulation of pressurized alkaline water electrolyzers is presented. The model has been developed following a multiphysics approach, integrating electrochemical, thermodynamic, heat transfer and gas evolution processes in order to faithfully reproduce the complete dynamical behavior of these systems. The model has been implemented on MATLAB/Simulink and validated through experimental data from a 1 Nm3h-1 commercial alkaline water electrolyzer, and the simulated results have been found to be consistent with the real measured values. This model has a great potential to predict the behavior of alkaline water electrolyzers coupled with renewable energy sources, making it a very useful tool for designing efficient green hydrogen production systems.

Barrios Rípodas, Ernesto

Email Address

person.page.identifierURI

Birth Date

Job Title

Last Name

First Name

person.page.departamento

person.page.instituteName

ORCID

person.page.observainves

person.page.upna

Name

Filters

Author

Subject

Date

Has files

Item Type

Type

Settings

Sort By

Results per page

Search Results