Open Access
Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides
(Nature Research, 2019) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua, 2018/PC021-022
The deposition of an indium oxide (In2O3) thin film on conventional planar waveguides (a coverslip and a glass slide) allows generating lossy mode resonances (LMR) by lateral incidence of light on the waveguide and by registering the optical spectrum in a spectrometer. This novel sensing system becomes an alternative to optical fibre, the substrate where LMR-based sensors have been developed so far, since it is easier to handle and more robust. An additional advantage is that cost effective waveguides, such as slides or coverslips, can be used in a platform that resembles surface plasmon resonance-based sensors in the Kretschmann configuration but without the need for a coupling prism and with the advantage of being able to generate TE and TM LMR resonances with metallic oxide or polymer thin films. The results are corroborated with simulations, which provide in-depth understanding of the phenomena involved in the sensing system. As a proof-of-concept for the optical platform, two refractometers were developed, one with low sensitivity and for a wide range of refractive indices, and the other with higher sensitivity but for a narrower refractive index range. The sensors presented here open up the path for the development of LMR-based chemical sensors, environmental sensors, biosensors, or even the generation of other optical phenomena with the deposition of multilayer structures, gratings or nanostructures, which is much easier in a planar waveguide than in an optical fibre.
Open Access
Increasing the sensitivity of an optic level sensor with a wavelength and phase sensitive single-mode multimode single-mode (SMS) fiber structure
(IEEE, 2017) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Vento Álvarez, José Raúl; Socorro Leránoz, Abián Bentor; Gallego Martínez, Elieser Ernesto; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica
The sensitivity of a liquid level sensor based on a single-mode-multimode-single-mode fiber structure has been increased by hydrofluoric acid etching. The etching process was analyzed and monitored both theoretical and experimentally, which permitted to observe that a sinusoidal spectrum can be obtained for low diameters. As an example, a 2.77 fold sensitivity increase was attained by etching from diameter 125 to 50 μm. Moreover, the sinusoidal shape of the optical spectrum permitted to monitor liquid level changes both in wavelength and phase. The cross sensitivity of the sensor to refractive index and temperature was also studied.
Open Access
Optical fiber vacuum sensor based on etched SMS structure and PDMS coating
(IEEE, 2020) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Corres Sanz, Jesús María; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, an optical fiber vacuum sensor based on a single-mode multimode single-mode (SMS) structure coated with polydimethylsiloxane (PDMS) is studied. The SMS structure generates an interferometric pattern based on multimode interference. The structure is dip-coated with a layer of PDMS, whose optical properties change when it is subjected to varying vacuum pressure. Different strategies are applied in an attempt to improve the final performance of the sensor, such as decreasing the diameter of the fiber and modifying the properties of the coating by modifying the proportion of solvent. Decreasing the diameter of the optical fiber and using toluene as a solvent are both proved to be successful strategies for increasing the sensitivity of the sensor. The devices are studied in the 1×10-3–10 mbar range with a maximum wavelength shift of 12 nm, leading to a maximum sensitivity of 35 nm/mbar. The simplicity of the fabrication process, which can be applied to more sensitive structures, suggests that PDMS may be a good choice for the development of optical fiber vacuum sensors.
Open Access
Multichannel refractometer based on lossy mode resonances
(IEEE, 2022) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Domínguez Rodríguez, Ismel; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work a new multiparameter sensor platform based on lossy mode resonances is presented. The structure consists of a soda-lime optical slab waveguide butt-coupled to multimode optical fibers. A variable thickness thin-film is deposited to generate multiple independent resonances on the same waveguide, which can be monitored using a single spectrometer. In order to show the potentiality of the structure, a broad resonance was selectively narrowed by etching sections of the LMR producer thin film. The spectral width is progressively reduced, allowing to selectively isolate independent resonances, which opens the path for multiple LMR generation in the same spectra in a multiparameter sensing platform. The experimental results were corroborated with a theoretical analysis based on the finite difference method (FDM). As a proof of concept, two refractometers on the same waveguide were fabricated and tested using PDMS cells. This platform can be easily miniaturized in order to integrate multiple sensors at low cost, what can be of interest for the development of multi-analyte biosensors probes. IEEE
Open Access
Generation of lossy mode resonances in planar waveguides toward development of humidity sensors
(IEEE, 2019) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Del Villar, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
Lossy mode resonances (LMRs) are typically obtained with optical fibre. The Kretschmann configuration is an alternative but LMRs are generated with angles approaching grazing incidence. In this work, a new setup is explored, based on the lateral incidence of light on conventional planar waveguides such as glass slides or coverslips. Indium tin oxide was deposited onto both types of waveguides generating LMRs. The results of the simulations carried out agree well with the experimental results. As an example of the potential of this new and simple optical configuration, a humidity sensor with a sensitivity of 0.212 nm/% relative humidity (RH) in the range from 65% to 90% of RH was developed, which expedites the development of other types of sensors already explored with LMR-based optical fibre sensors.
Open Access
Optical fiber vacuum sensor based on modal interferometer and PDMS coating
(IEEE, 2019) Ascorbe Muruzabal, Joaquín; Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Arregui San Martín, Francisco Javier; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors.
Open Access
Lossy mode resonances generated in planar configuration for two-parameter sensing
(IEEE, 2021-04-29) Fuentes Lorenzo, Omar; Corres Sanz, Jesús María; Domínguez Rodríguez, Ismel; Del Villar, Ignacio; Matías Maestro, Ignacio; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
This work shows a new sensor structure for simultaneous measurement of two parameters, temperature and refractive index. The optical configuration consists of incidence of light on the edge of a soda-lime coverslip fully coated with a CuO thin film and partially coated with a PDMS thick layer. This planar configuration permitted to generate two separated lossy mode resonances (LMRs): one centered at 600 nm and the other at 1000 nm. The second resonance is induced by the PDMS layer and it can be used to measure the temperature due to its high thermo-optic coefficient (the sensitivity is -1.75 nm/°C in the temperature range from 20 to 40 °C), whereas the first resonance is used for sensing refractive index with sensitivity of 1460 nm/RIU in the refractive index range from 1.3328 and 1.37. Finally, a calibration test was carried out using a calibrated oil series with refractive index ranging from 1.33 to 1.36. This work demonstrates the possibility of generating multiples resonances in a single structure as simple as a coverslip, which can be used as a multi-parameter interchangeable sensor, especially suitable for biological applications or the detection of heavy metals in water.
Open Access
Generation of lossy mode resonances with different nanocoatings deposited on coverslips
(Optical Society of America, 2020) Fuentes Lorenzo, Omar; Goicoechea Fernández, Javier; Corres Sanz, Jesús María; Del Villar, Ignacio; Ozcariz Celaya, Aritz; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
The generation of lossy mode resonances (LMRs) with a setup based on lateral incidence of light in coverslips is a simple platform that can be used for sensing. Here the versatility of this platform is proved by studying the deposition of different coating materials. The devices were characterized with both SEM and AFM microscopy, as well as ellipsometry, which allowed obtaining the main parameters of the coatings (thickness, refractive index and extinction coefficient) and relating them with the different sensitivities to refractive index attained with each material. In this way it was possible to confirm and complete the basic rules observed with lossy mode resonance based optical fiber sensors towards the design of simpler and more compact applications in domains such as chemical sensors or biosensors.
Open Access
Optimized strain long-period fiber grating (LPFG) sensors operating at the dispersion turning point
(IEEE, 2018) Del Villar, Ignacio; Fuentes Lorenzo, Omar; Chiavaioli, Francesco; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa eta Elektronikoa; Institute of Smart Cities - ISC; Ingeniería Eléctrica y Electrónica; Gobierno de Navarra / Nafarroako Gobernua
Two phenomena for enhancing the sensitivity of longperiod fiber gratings are combined toward an increase of the sensitivity to strain of this type of devices: the dispersion turning point (DTP) and the cladding diameter reduction by an etching process. The results prove that sensitivities up to 20 pm/με can be attained, which is a ten-fold improvement compared to the previous works. The sensitivity in the grating region, which is subjected to etching, does not depend on the order of the cladding mode responsible for the attenuation bands generated in the transmission spectrum, but on the proximity to the DTP for each mode order. On the other hand, the sensitivity to strain of the global structure, including the region without etching, can be increased for lower order modes in a perceptible way if the length of the etched region is smaller compared to the fiber region under stress. The experimental results are supported with simulations based on coupled-mode theory and on FIMMWAVE, which allows understanding the phenomena involved during the sensing process.
Open Access
Simultaneous generation of surface plasmon and lossy mode resonances in the same planar platform
(MDPI, 2022) Fuentes Lorenzo, Omar; Del Villar, Ignacio; Domínguez Catena, Iris; Corres Sanz, Jesús María; Matías Maestro, Ignacio; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
A planar waveguide consisting of a coverslip for a microscope glass slide was deposited in one of its two faces with two materials: silver and indium tin oxide (ITO). The incidence of light by the edge of the coverslip permitted the generation of both surface plasmon and lossy mode resonances (SPRs and LMRs) in the same transmission spectrum with a single optical source and detector. This proves the ability of this optical platform to be used as a benchmark for comparing different optical phenomena generated by both metal and dielectric materials, which can be used to progress in the assessment of different sensing technologies. Here the SPR and the LMR were compared in terms of sensitivity to refractive index and figure of merit (FoM), at the same time it was demonstrated that both resonances can operate independently when silver and ITO coated regions are surrounded by different refractive index liquids. The results were supported with numerical results that confirm the experimental ones.