Open Access
Analysis of tribological properties in disks of AA-5754 and AA-5083 aluminium alloys previously processed by equal channel angular pressing and isothermally forged
(MDPI, 2020) Luis Pérez, Carmelo Javier; Luri Irigoyen, Rodrigo; Puertas Arbizu, Ignacio; Salcedo Pérez, Daniel; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Ingeniería; Ingeniaritza
In the present study, the wear behaviour of two aluminium alloys (AA‐5754 and AA‐5083) is analysed where these have been previously processed by severe plastic deformation (SPD) with equal channel angular pressing (ECAP). In order to achieve the objectives of this study, several disks made of these alloys are manufactured by isothermal forging from different initial states. The microstructures of the initial materials analysed in this study have different accumulated deformation levels. In order to compare the properties of the nanostructured materials with those which have not been ECAP‐processed, several disks with a height of 6 mm and a diameter of 35 mm are manufactured from both aluminium alloys (that is, AA‐5754 and AA‐5083) isothermally forged at temperatures of 150 and 200 °C, respectively. These thus‐manufactured disks are tested under a load of 0.6 kN, which is equivalent to a stress mean value of 18 MPa, and at a rotational speed of 200 rpm. In order to determine the wear values, the disks are weighed at the beginning, at 10,000 revolutions, at 50,000 revolutions and at 100,000 revolutions, and then the volume‐loss values are calculated. This study was carried out using specific equipment, which may be considered to have a block‐on‐ring configuration, developed for testing in‐service wear behaviour of mechanical components. From this, the wear coefficients for the two materials at different initial states are obtained. In addition, a comparison is made between the behaviour of the previously ECAP-processed aluminium alloys and those that are non‐ECAP‐processed. A methodology is proposed to determine wear coefficients for the aluminium alloys under consideration, which may be used to predict the wear behaviour. It is demonstrated that AA‐5754 and AA‐5083 aluminium alloys improve wear behaviour after the ECAP process compared to that obtained in non‐ECAP‐processed materials.
Open Access
A proposal of a constitutive description for aluminium alloys in both cold and hot working
(MDPI, 2016) León Iriarte, Javier; Luis Pérez, Carmelo Javier; Fuertes Bonel, Juan Pablo; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Salcedo Pérez, Daniel; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
The most important difficulties when the behaviour of a part that is subjected to external mechanical forces is simulated deal with the determination of both the material thermo-mechanical properties and its boundary conditions. The accuracy of the results obtained from the simulation is directly related to the knowledge of the flow stress curve. Therefore, the determination of a material flow rule which is valid for both a wide temperature range and different initial deformation conditions in the starting material presents a great deal of interest when simulation results close to the experimental values are required to be obtained. In this present study, a novel flow stress curve is proposed that is able to accurately predict the behaviour of both materials with no previous accumulated strain and materials that have been previously subjected to severe plastic deformation processes. Moreover, it is possible to use it both for hot and cold working. The results are analysed in a wide test temperature range, which varies from room temperature to 300 °C, and from material previously processed by angular channel extrusion or with no previous strain accumulated. It is shown that the flow rule proposed is effective to model the material behaviour in a wide temperature range and it makes it possible to take the recrystallization phenomena that appear in previously deformed materials into account. In addition, the results obtained are compared with those predicted by other flow rules that exist in the prior literature. Furthermore, the study is complemented with finite element simulations and with a comparison between simulation and experimental results.
Open Access
Experimental and FEM analysis of wear behaviour in AA5083 ultrafine-grained cams
(MDPI, 2020) Luis Pérez, Carmelo Javier; Luri Irigoyen, Rodrigo; Fuertes Bonel, Juan Pablo; León Iriarte, Javier; Salcedo Pérez, Daniel; Puertas Arbizu, Ignacio; Ingeniería; Ingeniaritza
Severe plastic deformation (SPD) processes have attracted a great deal of both scientific and technological interest over the last few years as a consequence of the improvements that are possible to obtain in the microstructure and mechanical properties of the materials manufactured through the use of these kind of processes. However, the practical applications of such materials to obtain mechanical components are significantly fewer. As a direct consequence, the same thing has been observed in the development of studies that show the in-service behaviour of the mechanical components developed in this way. Since one of the industrial objectives of these SPD processes is to obtain functional parts, it is necessary to carry out studies to fill this gap. Therefore, in this study, an analysis of the wear that cams undergo when manufactured from an AA5083 aluminium-magnesium alloy is carried out. The cams were isothermally-forged from materials with and without previous SPD processing by equal channel angular pressing (ECAP). Subsequently, the wear behaviour of these cams was analysed by using specific equipment, which may have been considered to have a block-on-ring configuration, developed for testing in-service wear behaviour of mechanical parts. From this comparative wear study with cams, it is shown that previously-processed materials by ECAP have a better wear performance. Moreover, finite element modelling (FEM) simulations were also included to predict wear in the cams processed in this way. A good agreement between FEM and experimental results was obtained. It is this aspect of performing the wear tests on functional and real mechanical components, and not on laboratory samples, which makes this present research work novel.
Open Access
Design and mechanical properties analysis of AA5083 ultrafine grained cams
(MDPI, 2017) Salcedo Pérez, Daniel; Luis Pérez, Carmelo Javier; Luri Irigoyen, Rodrigo; Puertas Arbizu, Ignacio; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
This present research work deals with the development of ultrafine grained cams obtained from previously ECAP (Equal Channel Angular Pressing)-processed material and manufactured by isothermal forging. The design and the manufacturing of the dies required for the isothermal forging of the cams are shown. Optimization techniques based on the combination of design of experiments, finite element and finite volume simulations are employed to develop the dies. A comparison is made between the mechanical properties obtained with the cams manufactured from material with no previous deformation and with those from previously SPD (Severe Plastic Deformation)-processed material. In addition, a comparative study between the experimental results and those obtained from the simulations is carried out. It has been demonstrated that it is possible to obtain ultrafine grained cams with an increase of 10.3% in the microhardness mean value as compared to that obtained from material with no previous deformation.
Open Access
Design, optimization, and mechanical property analysis of a submicrometric aluminium alloy connecting rod
(Hindawi, 2015) Fuertes Bonel, Juan Pablo; León Iriarte, Javier; Luis Pérez, Carmelo Javier; Salcedo Pérez, Daniel; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Ultrafine grained materials have a great deal of both scientific and technological interest because they allow outstanding properties to be obtained. An improvement in the mechanical strength and in the ductility and a better fatigue behaviour are properties to be expected with these materials. However, in spite of the great number of scientific publications that deals with the mechanical property improvement, the number of practical applications of these materials is scant. In this present research work, equal channel angular pressing (ECAP) is used as a severe plastic deformation process (SPD) to obtain billets which are subsequently isothermally forged to obtain a connecting rod with submicrometric grain size. The optimization of the design process is shown as well as the die design. The objective variables to be fulfilled are the correct filling of the die and the required force to obtain the part. Moreover, a comparison is also included between the mechanical properties thus obtained and those obtained with traditional methods. Moreover, optical and SEM micrographs are also included in this research work.
Open Access
Mechanical properties analysis of an Al-Mg alloy connecting rod with submicrometric structure
(MDPI, 2015) León Iriarte, Javier; Salcedo Pérez, Daniel; Murillo Crespo, Óscar; Luis Pérez, Carmelo Javier; Fuertes Bonel, Juan Pablo; Puertas Arbizu, Ignacio; Luri Irigoyen, Rodrigo; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Over these last few years, there has been a growing interest in developing mechanical components from submicrometric materials due to the significant improvement that these materials present compared to their original state. This present research work deals with the study of the mechanical properties of a connecting rod isothermally forged from different starting materials. These materials are as follows: annealed aluminum alloy (AA) 5754, the same alloy previously deformed through equal channel angular pressing (ECAP) and a third case where the previously ECAP-processed material is subjected to a recovery heat treatment. A comparison is made between finite volume (FV) simulations and experimental tests with respect to hardness, plastic strain and forging force. Furthermore, the improvement in the mechanical properties of the connecting rod forged from predeformed material is evaluated in comparison to the connecting rod forged with annealed material. The microstructure of both cases is also compared at the end of the manufacturing process.
Open Access
Experimental modelling of critical damage obtained in Al-Mg and Al-Mn alloys for both annealed state and previously deformed by ECAP
(Elsevier, 2016) Luri Irigoyen, Rodrigo; Fuertes Bonel, Juan Pablo; Luis Pérez, Carmelo Javier; Salcedo Pérez, Daniel; Puertas Arbizu, Ignacio; León Iriarte, Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Assessing the damage produced in plastic deformation processes permits the optimum manner to shape a material that could avoid any cracks from appearing. In this present research work, the absolute critical damage in the following aluminium alloys: AA5754, AA5083 and AA3103 is to be determined. In order to do this, compression tests between plane-shape dies will be performed for the abovementioned alloys at a temperature range which varies from 25 °C to 300 °C and using Cockroft–Latham's prediction model. Furthermore, the results obtained by finite volume simulations will be compared with those obtained by experimental tests with isothermal upsetting. Given that in these last few years there has been a growing interest in obtaining mechanical components from submicrometric and/or nanometric structure materials which have been previously-processed by severe plastic deformation (SPD), this present research work deals with the determination of absolute critical damage for the abovementioned alloys once they have been ECAP (Equal Channel Angular Pressing) processed. This is considered to be of interest since it could allow the prediction of optimal processing conditions in advance.
Open Access
Analysis of fatigue and wear behaviour in ultrafine grained connecting rods
(MDPI, 2017) Luri Irigoyen, Rodrigo; Luis Pérez, Carmelo Javier; León Iriarte, Javier; Fuertes Bonel, Juan Pablo; Salcedo Pérez, Daniel; Puertas Arbizu, Ignacio; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Over the last few years there has been an increasing interest in the study and development of processes that make it possible to obtain ultra-fine grained materials. Although there exists a large number of published works related to the improvement of the mechanical properties in these materials, there are only a few studies that analyse their in-service behaviour (fatigue and wear). In order to bridge the gap, in this present work, the fatigue and wear results obtained for connecting rods manufactured by using two different aluminium alloys (AA5754 and AA5083) previously deformed by severe plastic deformation (SPD), using Equal Channel Angular Pressing (ECAP), in order to obtain the ultrafine grain size in the processed materials are shown. For both aluminium alloys, two initial states were studied: annealed and ECAPed. The connecting rods were manufactured from the previously processed materials by using isothermal forging. Fatigue and wear experiments were carried out in order to characterize the in-service behaviour of the components. A comparative study of the results was made for both initial states of the materials. Furthermore, Finite Element Modelling (FEM) simulations were used in order to compare experimental results with those obtained from simulations. In addition, dimensional wear coefficients were found for each of the aluminium alloys and initial deformation states. This research work aims to progress the knowledge of the behaviour of components manufactured from ultrafine grain materials.
Open Access
Design, simulation and manufacturing of a connecting rod from ultra-fine grained material and isothermal forging
(Elsevier, 2016) Fuertes Bonel, Juan Pablo; Luis Pérez, Carmelo Javier; Luri Irigoyen, Rodrigo; Salcedo Pérez, Daniel; León Iriarte, Javier; Puertas Arbizu, Ignacio; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
In this research work, a study on the mechanical properties of isothermal forging for connecting rods is made from previously ECAP (Equal Channel Angular Pressing)-processed AA1050 and AA5083 aluminium alloys. This severe plastic deformation (SPD) process is used in order to achieve a starting material with a submicrometric structure, thus improving the mechanical properties of the part. In this study, the design and the experimentation process is shown, where this involves the design stage by finite element simulations, the experimental tests and the use of metallographic techniques for the required properties to be analysed. Itis observed thatthere is an improvementin the mechanical properties when the starting material is ECAP-processed before carrying out the isothermal forging. This improvement consists in an increase of 20% in the hardness of the final connecting rod which also possesses a microstructure grain size of 500 nm. To come to these conclusions,the results obtained with the connecting rods manufactured by isothermal forging from previously ECAP-processed material are compared with those conventionally manufactured. Therefore,the feasibility and the advantages ofthe industrialmanufacturing ofmechanical components by isothermal forging from ECAP-processed material are demonstrated here as mechanical properties are achieved, as well as a better flow of the material and at a lower forging temperature. In the existing bibliography, there are no research works dealing with the manufacturing of connecting rods from ultra-fine grained material and that is the reason why this present study is considered to be of scientific and technological interest, and therefore, it may be considered to be at the frontline of current knowledge.