Open Access
Effect of the synthesis method on the morphology, textural properties and catalytic performance of La-hexaaluminates in the dry reforming of methane
(Elsevier, 2021) Torrez Herrera, Jonathan Josué; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work describes the synthesis of nickel/lanthanum hexaaluminates (NiO/LHA), optimizing the LHA synthesis method, as well as their performance in terms of stability and catalytic activity in the dry reforming of methane (DRM). The synthesis methods studied include co-precipitation, nitrate decomposition and freeze drying, using a La/Al molar ratio of 1:11 in all methods. Drying methods, namely oven drying (4 h at 353 K), vacuum drying (8 h at 353 K) + oven drying (2 h at 423 K) and heat treatment (12 h at 473 K) + oven drying (2 h at 373 K), were also optimized during selection of the final catalyst support. After calcination at 1473 K for 2 h, the presence of lanthanum aluminate (LaAlO3) and traces of LHA were found in all cases. Specific surface areas of 50, 32 and 30 m(2)/g were obtained for the samples AD1 (nitrate decomposition), FD1 (freeze drying), CP1 (co-precipitation). The nitrate decomposition method was selected and optimized to obtain the LHA structure at low temperature in the presence of Ni(II), using a La/Al/Ni molar ratio of 1/15/0.2. The results showed the formation of pure-phase hexaaluminate at 1473 K. The solids obtained were used as supports for nickel catalysts (10 wt%) for DRM at 973 K. The supports and catalysts were characterized by X-ray diffraction (XRD), N-2 adsorption at 77 K, temperature-programmed reduction (TPR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The simulation of the TPR patterns of the catalysts allowed determining the type of metal support interaction and the activation energy of the system as well as the rest of the kinetic parameters. A cumulative mean activation energy of 100.7 kJ/mol was determined for the catalysts. The metallic morphologies, dispersion and distribution of NiO on the surface of the LHA support were analyzed considering a theoretical simulation of the reduction profiles, obtaining an average growth factor of 1.4, which indicates that the metallic phase is growing in one and two dimensions. The NiO/LHA catalysts synthesized were found to be active and very stable in the DRM reaction after 20 h of reaction with an average selectivity H-2/CO upper than 0.90. The differences observed can be related to the textural properties developed during the optimized nitrate decomposition method. The characterization analysis by simulation, TPR, XRD, TEM, SEM allowed us to establish the effect of the textural properties, the metal interaction, the growth of the nickel grains and their distribution in the support on the catalytic performance in DRM. The better performance was obtained with the catalysts with higher porosity and greater support metal interaction, which allowed obtaining a better distribution of the metallic phase, thus generating less harmful carbonaceous species for the activity of the catalyst and therefore showing the best values of catalytic stability and conversion. Finally, three types of coke were identified from HR-TEM and EDS analysis: graphitic, filamentous and CNT, showing different effects on the catalytic behavior deactivation being the presence of graphitic more aggressive than the other two species.
Open Access
Bimetallic (Pt-Ni) La-hexaaluminate catalysts obtained from aluminum saline slags for the dry reforming of methane
(Elsevier, 2021) Torrez Herrera, Jonathan Josué; Korili, Sophia A.; Gil Bravo, Antonio; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Ciencias; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
This work describes the synthesis of platinum-nickel/lanthanum hexaaluminates (PtNi/LHA) and their performance in terms of stability and catalytic activity in the dry reforming of methane (DRM) at 973 K. An Al solution (9.40 g/L) obtained from an Al saline slag waste by acid extraction was used to synthesize the hexaaluminate by mixing with a stoichiometric amount of lanthanum nitrate and methanol/Peg400/PegMn400 under hydrothermal conditions at 493 K for 16 h. After calcination at 1473 K for 2 h, the presence of LHA was confirmed. Wet impregnation of the synthesized support was used to obtain an initial Ni/LHA catalyst (10 wt% NiO) and the modified PtNi/LHA catalysts (0.2–1 wt% Pt). The support and catalysts were characterized by X-ray diffraction (XRD), N2 adsorption at 77 K, temperature- programmed reduction (TPR), scanning electron microscopy (SEM) and transmission electron microscopy (HR- TEM). The analysis of the TPR patterns for the catalysts allowed the type of metal support interaction and NiO species to be determined, with a weak interaction with the support being observed in all cases. The presence of Pt promoted NiO reducibility. The PtNi/LHA catalysts synthesized were found to be active and very stable in the DRM reaction after reaction for 50 h. The catalytic behavior was evaluated from the CO2 and CH4 conversions, as well as the H2/CO selectivity, with values of between 89% and 92% in almost all the time range evaluated. The presence of Pt improved the stability and catalytic performance of Ni/LHA thus improving resistance to coke formation.
Open Access
Layered double hydroxides for CO2 adsorption at moderate temperatures: synthesis and amelioration strategies
(Elsevier, 2023) Santamaría Arana, Leticia; Korili, Sophia A.; Gil Bravo, Antonio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Curving the CO2 atmospheric levels is one of the challenges of this century, given its direct impact on climate change. Of the several strategies of CO2 capture and storage, sorption-enhanced water–gas shift (SEWGS) process, a combination of CO2 adsorption and the water–gas shift reaction, has been appointed as one of the most promising techniques due to is low energy consumption and high efficiency. SEWGS operating settings at both moderate temperature (200–450 ◦C) and high pressure (more than 10 bar) bring the need to find an adsorbent capable of working at these conditions. Calcined layered double hydroxides (LDH) have been proven to give the best results in this range of pressure/temperatures even though its performance can be greatly improved. Herein, a state-of-art of the research accomplished up until now is presented. Several strategies can be followed to improve the adsorbents performance: the synthesis method, LDH composition, modifications employed to promote their adsorption capacity or how the adsorption conditions can affect their efficiency
Embargo
Surface tuning of a highly crystalline Ni/LaAlO3 perovskite catalyst obtained from aluminum saline slags using various synthesis methods for the dry reforming of methane
(Elsevier, 2025-03-01) Muñoz Alvear, Helir Joseph; Korili, Sophia A.; Gil Bravo, Antonio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
This research presents the first synthesis of nickel-modified lanthanum aluminate (Ni/LaAlO3) perovskite from aluminum (Al) saline slag waste involving acid extraction. Two methods were employed to extract Al: a 2 M HCl aqueous solution (AH) and various citric acid (CA) aqueous solutions (0.5, 1.0, or 2.0 M). Three preparation methods (Pechini, modified citrate, and metal–organic gel) were evaluated to obtain the pure lanthanum aluminate (LaAlO3) phase. This study also investigated the effects of several factors, with some variations being observed depending on the methodology used. The factors analyzed were: (i) preparation method; (ii) type of Al precursor solution (either extracted using HCl or CA); (iii) ligand/cations molar ratio (La3 + + Al3+), ranging from 0.3 to 3.0; (iv) CA concentration; (v) molar ratio (La/Al), between 0.5 and 1.0; (vi) calcination temperature; and (vii) acid etching of the final materials with aqueous dilute nitric acid (HNO3). The results indicated that it is possible to obtain LaAlO3 perovskite using all three methodologies and the Al extracted from saline slags. For the Pechini and metal–organic gel methods, ligand/cations molar ratios (La3+ + Al3+) of 3.0 and between 0.3 (with CA) and 1.5 (with AH), respectively, were obtained, while a CA concentration of 1.0 M was used for the modified citrate method. The optimal molar ratio (La/Al) for obtaining the perovskite was 1.0 in all three methods. The perovskite was synthesized at low temperatures, starting from 650 °C, and was obtained in a completely pure form at between 950 and 1050 °C. Treatment with aqueous dilute acid had a marked effect, especially on the materials obtained when using the initial solution extracted with 2.0 M HCl. This treatment was particularly beneficial for the material prepared using the Pechini method, which induced a 2.5-fold increase in the specific surface area and total pore volume without affecting the crystalline structure, and allowed the specificity of the nickel (Ni) active sites incorporated to be directed, particularly towards a higher proportion of β1 reducible species. This result improved the catalytic performance in the dry reforming of methane (DRM) reaction, achieving conversions of up to 73 % in CO2 and up to 70 % in CH4, with average selectivity of 0.93 after 20 h of reaction. These outcomes even surpassed the reference catalyst, which was entirely prepared using commercial-grade reagents. Factors such as the presence of other metals in the slag and the versatility of cationic substitution contributed to enhancing the physicochemical properties of the catalysts. Ultimately, all of this led to suppression of the formation of double-walled filamentous carbon deposits, which tend to deactivate the catalyst due to sintering and deformation of the active phase.

Gil Bravo, Antonio

Email Address

person.page.identifierURI

Birth Date

Job Title

Last Name

First Name

person.page.departamento

person.page.instituteName

ORCID

person.page.observainves

person.page.upna

Name

Filters

Author

Subject

Date

Has files

Item Type

Type

Settings

Sort By

Results per page

Search Results