Open Access
Outstanding performance of rehydrated Mg-Al hydrotalcites as heterogeneous methanolysis catalysts for the synthesis of biodiesel
(Elsevier, 2018) Navajas León, Alberto; Campo Aranguren, Idoia; Moral Larrasoaña, Ainara; Echave, Javier; Sanz, Oihane; Montes, Mario; Odriozola, José A.; Arzamendi Manterola, Gurutze; Gandía Pascual, Luis; Química Aplicada; Kimika Aplikatua; Institute for Advanced Materials and Mathematics - INAMAT2
There is still a need for active, selective and stable heterogeneous catalysts for the synthesis of biodiesel. In this work, magnesium-aluminium hydrotalcites with Mg/Al molar ratios within the 1.5–5 range were synthesized by coprecipitation and used as transesterification catalysts for the synthesis of biodiesel. The mixed oxides obtained after calcination recovered the hydrotalcite structure in the form of meixnerite after rehydration in boiling water. The solids were characterized by XRD, TGA, N2 adsorption-desorption, and SEM. Basic properties were assessed by means of Hammett indicators and CO2-TPD. Rehydrated materials with the highest Mg/Al ratios showed some distinctive features: low surface area, well defined flake-like crystals, high basicity and strong basic sites with H_ values above 11. They were also the most active catalysts allowing to achieve 51–75% sunflower oil methanolysis conversion after 8 h of reaction under mild conditions (60 °C, 1 atm), methanol/oil molar ratio of 12 using between 2 and 6 wt% of catalyst. The conversion increased up to 96% (92% fatty acid methyl esters yield) using 2 wt% catalyst and methanol/oil molar ratio of 48. Catalyst leaching was not a serious problem with these solids that could be reutilized maintaining very good activities. A general accordance between solids basic properties and their catalytic performance has been observed. These results are among the best reported in the literature for heterogeneous methanolysis catalysts and have been attributed to the high basicity of the rehydrated solids and the presence of strong and accessible basic sites probably consisting in interlayer hydroxide anions at the edges of the crystals.
Open Access
Experimental study of the performance and emission characteristics of an adapted commercial four-cylinder spark ignition engine running on hydrogen-methane mixtures
(Elsevier, 2014) Diéguez Elizondo, Pedro; Urroz Unzueta, José Carlos; Marcelino Sádaba, Sara; Pérez Ezcurdia, Amaya; Benito Amurrio, Marta; Sáinz Casas, David; Gandía Pascual, Luis; Ingeniería; Ingeniaritza
The use of hydrogen/methane mixtures with low methane contents as fuels for internal combustion engines (ICEs) may help to speed up the development of the hydrogen energy market and contribute to the decarbonization of the transportation sector. In this work, a commercial 1.4 L four-cylinder Volkswagen spark-ignition engine previously adapted to operate on pure hydrogen has been fueled with hydrogen/methane mixtures with 5–20 vol.% methane (29.6–66.7 wt.%). An experimental program has been executed by varying the fuel composition, air-to-fuel ratio (λ), spark advance and engine speed. A discussion of the results regarding the engine performance (brake torque, brake mean effective pressure, thermal efficiency) and emissions (nitrogen oxides, CO and unburned hydrocarbons) is presented. The results reveal that λ is the most influential variable on the engine behavior due to its marked effect on the combustion temperature. As far as relatively high values of λ have to be used to prevent knock, the effect on the engine performance is negative. In contrast, the specific emissions of nitrogen oxides decrease due to a reduced formation of thermal NOx. A clear positive effect of reducing the spark advance on the specific NOx emissions has been observed as well. As concerns CO and unburned hydrocarbons (HCs), their specific emissions increase with the methane content of the fuel mixture, as expected. However, they also increase as λ increases in spite of the lower fuel concentration due to a proportionally higher reduction of the power. Finally, the effect of the increase of the engine speed is positive on the CO and HCs emissions but negative on that of NOx due to improved mixing and higher temperature associated to intensified turbulence in the cylinders.
Open Access
Oak wood extracts applied to the grapevine. An alternative to obtain quality Garnacha wines
(Elsevier, 2018) Jiménez Moreno, Nerea; Moler Cuiral, José Antonio; Urmeneta Martín-Calero, Henar; Suberviola Ripa, Julián; Cibriain Sabalza, Félix; Gandía Pascual, Luis; Ancín Azpilicueta, Carmen; Química Aplicada; Kimika Aplikatua; Institute for Advanced Materials and Mathematics - INAMAT2; Estadística e Investigación Operativa; Estatistika eta Ikerketa Operatiboa
Open Access
Comparative performance of coke oven gas, hydrogen and methane in a spark ignition engine
(Elsevier, 2020) Ortiz Imedio, Rafael; Ortiz, A.; Urroz Unzueta, José Carlos; Diéguez Elizondo, Pedro; Gorri, D.; Gandía Pascual, Luis; Ortiz, I.; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería
In this study, coke oven gas (COG), a by-product of coke manufacture with a high volumetric percentage of H2 and CH4, has been identified as auxiliary support and promising energy source in stationary internal combustion engines. Engine performance (power and thermal efficiency) and emissions (NOx, CO, CO2 and unburned hydrocarbons) of COG, pure H2 and pure CH4 have been studied on a Volkswagen Polo 1.4 L port-fuel injection spark ignition engine. Experiments have been done at optimal spark advance and wide open throttle, at different speeds (2000–5000 rpm) and various air-fuel ratios (λ) between 1 and 2. The obtained data revealed that COG combines the advantages of pure H2 and pure CH4, widening the λ range of operation from 1 to 2, with very good performance and emissions results comparable to pure gases. Furthermore, it should be highlighted that this approach facilitates the recovery of an industrial waste gas.
Open Access
Kinetic analysis and CFD simulations of the photocatalytic production of hydrogen in silicone microreactors from water-ethanol mixtures
(Elsevier, 2017) Castedo, Alejandra; Uriz Doray, Irantzu; Soler, Lluís; Gandía Pascual, Luis; Llorca Piqué, Jordi; Kimika Aplikatua; Institute for Advanced Materials and Mathematics - INAMAT2; Química Aplicada
Silicone microreactors containing microchannels of 500 μm width in a single or triple stack configuration have been manufactured, coated with an Au/TiO2 photocatalyst and tested for the photocatalytic production of hydrogen from water-ethanol gaseous mixtures under UV irradiation. Computational fluid dynamics (CFD) simulations have revealed that the design of the distributing headers allowed for a homogeneous distribution of the gaseous stream within the channels of the microreactors. A rate equation for the photocatalytic reaction has been developed from the experimental results obtained with the single stack operated under different ethanol partial pressures, light irradiation intensities and contact times. The hydrogen photoproduction rate has been expressed in terms of a Langmuir-Hinshelwood-type equation that accurately describes the process considering that hydrogen is produced through the dehydrogenation of ethanol to acetaldehyde. This equation incorporates an apparent rate constant (kapp) that has been found to be proportional to the intrinsic kinetic rate constant (k), and that depends on the light intensity (I) as follows: kapp = k·I0.65. A three-dimensional isothermal CFD model has been developed in which the previously obtained kinetic equation has been implemented. The model adequately describes the production of hydrogen of both the single and triple stacks. Moreover, the specific hydrogen productions (i.e. per gram of catalyst) are very close for both stacks thus suggesting that the scaling-up of the process could be accomplished by simply numbering-up. However, small deviations between the experimental and predicted hydrogen production suggest that a fraction of the radiation is absorbed by the microreactor components which should be taken into account for scaling-up purposes.
Open Access
Functionalization of 3D printed ABS filters with MOF for toxic gas removal
(Elsevier, 2020) Pellejero, Ismael; Almazán, Fernando; Lafuente, María; Urbiztondo, Miguel A.; Dobrek, Martin; Bechelany, Mikhael; Julbe, Anne; Gandía Pascual, Luis; Institute for Advanced Materials and Mathematics - INAMAT2; Gobierno de Navarra / Nafarroako Gobernua, PC052-23; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Acrylonitrile butadiene styrene (ABS) is one of the most extensively used polymer in 3D printing manufacturing due to its competitive thermal and mechanical properties. Recently, a special attention has been devoted to novel ABS composites featuring extra functionalities e.g. in the area of VOC removal. Herein, we report on a facile protocol for the functionalization of 3D printed ABS filters with a MOF (Metal- Organic Framework) material (ZIF-8) targeting the conception of attractive gas filters. The proposed synthesis strategy consists in low temperature ALD (Atomic Layer Deposition) of ZnO on the ABS grid followed by the hydrothermal conversion of ZnO to ZIF-8, both steps being conducted at 60 °C. In such way, the method enables an effective growth of ZIF-8 without altering the stability of the polymeric ABS support. The as-fabricated ABS/ZIF-8 filters offer a promising adsorption behaviour for dimethyl methylphosphonate (~20.4 mg of DMMP per gram of ZIF-8), thus proving their potential for toxic gas capture applications.
Open Access
In situ synthesis of SERS-active Au@POM nanostructures in a microfluidic device for real-time detection of water pollutants
(American Chemical Society, 2020) Lafuente Adiego, Marta; Pellejero, Ismael; Clemente, Alberto; Urbiztondo, Miguel A.; Mallada, Reyes; Reinoso, Santiago; Pina, María del Pilar; Gandía Pascual, Luis; Institute for Advanced Materials and Mathematics - INAMAT2; Gobierno de Navarra / Nafarroako Gobernua; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
We present a simple, versatile and low-cost approach for the preparation of SERS-active regions within a microfluidic channel 50 cm in length. The approach involves the UV-light-driven formation of polyoxometalate-decorated gold nanostructures, Au@POM (POM: H3PW12O40 (PW) and H3PMo12O40 (PMo)), that self-assemble in situ on the surface of the PDMS microchannels without any extra functionalization procedure. The fabricated LoCs were characterized by SEM, UV-Vis, Raman, XRD and XPS techniques. The SERS activity of the resulting Au@POM–coated lab-on-a-chip (LoC) devices was evaluated in both static and flow conditions using Rhodamine R6G. The SERS response of Au@PW–based LoCs was found superior to Au@PMo counterparts and outstanding when compared to reported data on metal@POM nanocomposites. We demonstrate the potentialities of both Au@POM–coated LoCs as analytical platforms for real time detection of the organophosphorous pesticide Paraoxon-methyl at 10-6 M concentration level.
Open Access
Gold supported on CuOₓ/CeO₂ catalyst for the purification of hydrogen by the CO preferential oxidation reaction (PROX)
(Elsevier, 2014) Arzamendi Manterola, Gurutze; Gandía Pascual, Luis; Química Aplicada; Kimika Aplikatua
Hydrogen produced from the conversion of hydrocarbons or alcohols contains variable amounts of CO that should be removed for some applications such as feeding low-temperature polymer electrolyte membrane fuel cells (PEMFCs). The CO preferential oxidation reaction (PROX) is particularly well-suited for hydrogen purification for portable and on-board applications. In this work, the synthesis and characterization by XRF, BET, XRD, Raman spectroscopy and H2-TPR of a gold catalyst supported on a coppercerium mixed oxide (AuCeCu) for the PROX reaction are presented. The comparison of this catalyst with the copper–cerium mixed oxide (CeCu) revealed that the experimental procedure used for the deposition of gold gave rise to the loss of reducible material by copper lixiviation. However, the AuCeCu solid was more active for CO oxidation at low temperature. A kinetic study has been carried over the AuCeCu catalyst for the PROX reaction and compared with that of the CeCu catalyst. The main difference between the models affected the contribution of the CO adsorption term. This fact may be related to the surface electronic activity produced by the interaction of the cationic species in the AuCeCu solid, able to create more active sites for the CO adsorption and activation in the presence of gold.
Open Access
Effect of oxygen addition, reaction temperature and thermal treatments on syngas production from biogas combined reforming using Rh/alumina catalysts
(Elsevier, 2019) Navarro Puyuelo, Andrea; Reyero Zaragoza, Inés; Moral Larrasoaña, Ainara; Bimbela Serrano, Fernando; Bañares, Miguel A.; Gandía Pascual, Luis; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
Dry reforming and partial oxidation of biogas were studied using 0.5 wt.% Rh/Al2O3 catalysts, both inhouse prepared and commercial. The effects of O2 addition on syngas yield and biogas conversion were studied at 700 C using different O2/CH4 ratios in the gas feeding stream: 0 (dry reforming), 0.12, 0.25, 0.45 and 0.50. The highest CH4 conversion, H2 yield and H2/CO molar ratio were obtained with an O2/CH4 ratio of 0.45, even though simultaneous valorization of both CH4 and CO2 could be best attained when the O2/CH4 ratio was 0.12. Increased biogas conversions and syngas yields were obtained by increasing reaction temperatures between 650 and 750 C. A detrimental influence on catalytic activity could be observed when the catalyst was subjected to calcination. Increasing the hold time of the thermal conditioning of the catalyst under inert flow altered Rh dispersion, though had no significant impact on catalyst performance in the dry reforming of methane at 700 C and 150 N L CH4/(gcat h). Characterization of spent samples after reaction by Raman spectroscopy revealed the presence of carbonaceous deposits of different nature, especially on the commercial(named as Rh com) and calcined (Rh calc) catalysts, though oxygen addition in the biogas feed significantly reduced the amount of these deposits. The Rh catalysts that had not been calcined after impregnation (Rh prep) did not present any noticeable characteristic peaks in the G and D bands. In particular, scanning transmission electron microscopy (STEM) images of the spent Rh prep sample revealed the presence of very highly dispersed Rh nanoparticles after reaction, of particle sizes of about 1 nm, and no noticeable C deposits. Combined oxy-CO2 reforming of biogas using highly dispersed and low metal-loading Rh/Al2O3 catalysts with low O2 dosage in the reactor feed can be used to effectively transform biogas into syngas.
Open Access
Characterization of combustion anomalies in a hydrogen-fueled 1.4 L commercial spark-ignition engine by means of in-cylinder pressure, block-engine vibration, and acoustic measurements
(Elsevier, 2018) Diéguez Elizondo, Pedro; Urroz Unzueta, José Carlos; Sáinz Casas, David; Machín Mindán, Jorge; Arana Burgui, Miguel; Gandía Pascual, Luis; Institute for Advanced Materials and Mathematics - INAMAT2
Abnormal combustion phenomena are among the main hurdles for the introduction of hydrogen in the transportation sector through the use of internal combustion engines (ICEs). For that reason the challenge is to guarantee operation free from combustion anomalies at conditions close to the ones giving the best engine output (maximum brake torque and power). To this end, an early and accurate detection of abnormal combustion events is decisive in order to allow the electronic control unit deciding suitable correcting actions. In this work, an automotive size 4-cylinder 1.4 L naturally aspirated port-fuel injection spark ignition Volkswagen engine adapted to run on hydrogen has been investigated. Three distinct methods (in-cylinder pressure, block-engine vibration and acoustic measurements) have been employed to detect abnormal combustion phenomena provoked through the enrichment of the hydrogen-air mixture fed to the cylinders under a wide range of engine speeds (1000–5000 rpm). It has been found that the high-frequency components of the in-cylinder pressure and block engine acceleration signals obtained after a Fourier transform analysis can be used for very sensitive detection of knocking combustion cycles. In the case of the ambient noise measurements, a spectral analysis in terms of third octave bands of the signal recorded by a microphone allowed an accurate characterization. Combustion anomalies could be detected through more intense octave bands at frequencies between 250 Hz and 4 kHz in the case of backfire and between 8 kHz and 20 kHz for knock. Computational fluid dynamics simulations performed indicated that some characteristics of the engine used such as the cylinder valves dimensions and the hydrogen flow rate delivered by the injectors play important roles conditioning the likelihood of suffering backfire events.