Open Access
Revisión sobre la corrosión de tubos sobrecalentadores en plantas de biomasa
(CENIM, 2006) Berlanga Labari, Carlos; Fernández Carrasquilla, Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
En el diseño de plantas de biomasa es muy importante tener en cuenta la temperatura del vapor para no tener problemas de corrosión. Esto, es debido al alto contenido de potasio y cloro que tienen la mayoría de los biocombustibles y, en especial, la paja de cereal. El objetivo de esta revisión es condensar el conocimiento actual sobre la corrosión de los sobrecalentadores a altas temperaturas provocada por compuestos clorados en plantas de biomasa. El cloro puede causar corrosión acelerada debido a la pérdida de metal del sobrecalentador, ataque interno y formación de capas de óxidos no adherentes. Los problemas de corrosión más severos en una caldera de biomasa se producen en los depósitos formados sobre los tubos sobrecalentadores. En la primera parte de esta revisión, se describen los mecanismos de corrosión propuestos en función de las condiciones de trabajo predominantes en la caldera. La segunda parte, se centra en revisar los estudios realizados para comprobar el comportamiento de los materiales mediante ensayos realizados en la caldera y en el laboratorio. En primer lugar, se describen las investigaciones realizadas sobre aleaciones convencionales y después las realizadas sobre las aleaciones desarrolladas en los últimos años y recubrimientos.
Open Access
Using the multi-response method with desirability functions to optimize the zinc electroplating of steel screws
(MDPI, 2018) Lostado Lorza, Rubén; Martínez Calvo, María Ángeles; Berlanga Labari, Carlos; Rivero Fuente, Pedro J.; Institute for Advanced Materials and Mathematics - INAMAT2
Zinc electroplating is a coating process controlled by several input process parameters. However, the commonly used input parameters for setting the process of zinc deposition are current density, temperature of the coating solution, zinc concentration, deposition time, and concentration of additives (conditioner and brightener). The power consumed in the zinc plating process, coating thickness, increase in coating mass, and corrosion resistance are considered to be outputs or zinc coating parameters. They are widely used when the zinc coating requirements are based on the coating process cost, coating process speed, corrosion resistance, and coating thickness. This paper seeks to determine regression models by the response surface method (RSM) that relate the zinc coating parameters to the input parameters in steel screws. When considering the coating requirements of cost, coating process speed, corrosion resistance, and coating thickness, the optimal input parameters were found by using a multi-response surface (MRS). Input parameters of 0.3 amps/dm(2), 20.0 degrees C, 13.9 g/L, 45 min, 28.5 mL/L, and 2.8 mL/L, respectively (relative to the commonly used input parameters detailed above), were obtained when considering the cost. Considering minimization of the deposition time, the input parameters obtained were 0.5 amps/dm(2), 24.6 degrees C, 13.9 g/L, 45 min, 26.9 mL/L, and 1.1 mL/L, respectively. The optimal inputs to maximize the corrosion resistance were 0.6 amps/dm(2), 32.4 degrees C, 14.0 g/L, 45 min, 28.7 mL/L, and 2.5 mL/L, respectively. Finally, when maximizing the coating thickness, the inputs were 0.7 amps/dm(2), 38.4 degrees C, 12.2 g/L, 45 min, 26.5 mL/L, and 1.5 mL/L, respectively.
Open Access
Functionalized electrospun fibers for the design of novel hydrophobic and anticorrosive surfaces
(MDPI, 2018) Rivero Fuente, Pedro J.; Yurrita Silanes, David; Berlanga Labari, Carlos; Rodríguez Trías, Rafael; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, Navarre-PRO-UPNA18 (6107)
In this work, a novel coating was deposited on aluminum alloy samples by using a combination of electrospinning and chemical vapor deposition (CVD-silanization) techniques in order to create a functionalized film with an enhancement of both corrosion resistance and hydrophobicity. The electrospinning technique makes the fabrication of highly crosslinked electrospun fibers possible by the combination of both poly(acrylic acid) and beta-cyclodextrin, respectively, which can be easily functionalized in a further step by using the CVD-silanization process due to the evaporation of a hydrophobic molecule such as 1H,1H,2H,2H-Perflurodecyltriethoxysilane. In addition, the resultant electrospun fibers with a high degree of insolubility have been successfully fabricated and metal oxide nanoparticles (TiO(2)NPs) have been incorporated into the electrospun polymeric solution in order to improve the corrosion protection. The surface morphology has been determined by using light optical microscopy, atomic force microscopy, scanning electron microscopy, and water contact angle (WCA) measurements. The corrosion resistance has been evaluated by using both potentiodynamic polarization and pitting corrosion tests. Finally, the results related to WCA measurements after CVD-silanization corroborate that the surfaces have been successfully functionalized with a hydrophobic behavior in comparison with the electrospinning process, showing a considerable difference in the roughness.
Open Access
Revisión y estado del arte de la corrosividad del etanol y sus mezclas con gasolina
(CENIM, 2011) Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Fernández Carrasquilla, Javier; Universidad Pública de Navarra. Departamento de Ingeniería Mecánica, Energética y de Materiales; Nafarroako Unibertsitate Publikoa. Mekanika, Energetika eta Materialen Ingeniaritza Saila
Actualmente, el etanol se presenta como una fuente importante de combustible renovable para el sector de la automoción. Se sabe que los carburantes tradicionales, como la gasolina, no han causado problemas de corrosión, debido principalmente a su baja miscibilidad en el agua. En cambio, los biocarburantes en base alcohol pueden contener una considerable cantidad de agua y, además, se puede producir la oxidación parcial de sus componentes por su exposición a la atmósfera. Estas reacciones pueden ocasionar corrosión y posterior fallo, de cualquier componente metálico en contacto con las mezclas etanol-gasolina. En consecuencia, todos los sectores relacionados con la industria que emplean este combustible, empresas productoras, logística, dispensadores y fabricantes de vehículos, pueden estar afectados por esta problemática. Esto hace que este tema sea muy interesante, tanto desde un punto de vista científico como industrial. En este trabajo se revisa sistemáticamente todos los aspectos relacionados con la corrosión que produce el etanol y sus mezclas con gasolina, con el objetivo de conocer en profundidad el estado actual de las investigaciones, así como para orientar trabajos futuros que estén afectados, tanto de forma directa o indirecta con esta temática.
Open Access
Study of corrosion in a biomass boiler
(Hindawi, 2013) Berlanga Labari, Carlos; Ruiz Bermejo, José Antonio; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Biomass plants, apart from producing energy, help to reduce CO2(g) emissions. One of the biggest problems for their development is superheater corrosion due to fuel corrosivity, especially of the straw. This limits both the temperature of the vapour and also the effectiveness of the plant. In order to know more about the reactions which happen inside the boiler of biomass, thermodynamic calculations using software (HSC Chemistry) have been carried out. Field tests have been carried out in the Sang¨uesa Biomass Plant in Navarra (Spain): determination of the types of oxides and the deposits formed on the superheaters tubes as well as a program to measure temperatures. Finally, the global results are discussed.
Open Access
Effect of the temperature in the mechanical properties of austenite, ferrite and sigma phases of duplex stainless steels using hardness, microhardness and nanoindentation techniques
(MDPI, 2017) Argandoña Salinas, Gorka; Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Rivero Fuente, Pedro J.; Peña, Julio; Rodríguez Trías, Rafael; Mekanika, Energetika eta Materialen Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Mecánica, Energética y de Materiales
The aim of this work is to study the hardness of the ferrite, austenite and sigma phases of a UNS S32760 superduplex stainless steel submitted to different thermal treatments, thus leading to different percentages of the mentioned phases. A comparative study has been performed in order to evaluate the resulting mechanical properties of these phases by using hardness, microhardness and nanoindentation techniques. In addition, optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD) have been also used to identify their presence and distribution. Finally, the experimental results have shown that the resulting hardness values were increased as a function of a longer heat treatment duration which it is associated to the formation of a higher percentage of the sigma phase. However, nanoindentation hardness measurements of this sigma phase showed lower values than expected, being a combination of two main factors, namely the complexity of the sigma phase structure as well as the surface finish (roughness).
Open Access
Relationship between microstructure and fracture types in a UNS S32205 duplex stainless steel
(ABM, ABC, ABPol, 2013) Biezma Moraleda, María Victoria; Berlanga Labari, Carlos; Argandoña Salinas, Gorka; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Duplex stainless steels are susceptible to the formation of sigma phase at high temperature which could potentially be responsible for catastrophic service failure of components. Thermal treatments were applied to duplex stainless steels in order to promote the precipitation of different fractions of sigma phase into a ferrite-austenite microstructure. Quantitative image analysis was employed to characterize the microstructure and Charpy impact tests were used in order to evaluate the mechanical degradation caused by sigma phase presence. The fracture morphology of the Charpy test specimens were thoroughly observed in SEM, looking for a correlation between the microstructure and the fracture types in UNS S32205 duplex stainless steel. The main conclusion is the strong embrittlement effect of sigma phase since it is possible to observe a transition from transgranular fracture to intergranular fracture as increases the percentage of sigma phase. Thus, the mixed modes of fracture are predominant in the present study with high dependence on sigma phase percentages obtained by different thermal treatments.
Open Access
Hydrophobic and corrosion behavior of sol-gel hybrid coatings based on the combination of TiO2 NPs and fluorinated chains for aluminum alloys protection
(MDPI, 2018) Rivero Fuente, Pedro J.; Maeztu Redin, Juan Deyo; Berlanga Labari, Carlos; Miguel, Adrián; Rodríguez Trías, Rafael; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, Navarre-PRO-UPNA18-6107-FRRRIO
In this work, layers of a sol-gel hybrid matrix doped with metal oxide nanoparticles (TiO2 NPs) have been deposited on flat samples of AA6061-T6 aluminum alloy using the dip-coating technique, with the aim of obtaining coatings with better anti-corrosive and hydrophobic properties. Two different organic modified silica alkoxides, namely 3-(glycidyloxypropyl)trimethoxysilane (GPTMS) and methyltriethoxysilane (MTEOS), have been used for an adequate entrapment of the metal oxide nanoparticles. In addition, a fluorinated metal-alkoxide precursor has also been added to the hybrid matrix in order to improve the hydrophobic behavior. The experimental results corroborate that the presence of these TiO2 NPs play an important role in the development of the sol-gel hybrid coatings. The water contact angle (WCA) measurements, as well as pencil hardness tests indicate that TiO2 NPs make a considerable increase in the resultant hydrophobicity possible, with better mechanical properties of the coatings. The coating thickness has been measured by cross-section scanning electron microscopy (SEM). In addition, a glow discharge optical emission spectroscopy (GD-OES) analysis has been carried out in order to corroborate the adequate entrapment of the TiO2 NPs into the sol-gel coatings. Finally, potentiodynamic polarization tests and electrochemical impedance spectroscopy (EIS) have been performed in order to evaluate the corrosion resistance of the coatings. All the results provide insights into the efficacy of the developed sol-gel hybrid coatings for anticorrosive purposes with good mechanical properties.
Open Access
Characterization of two iron bullets from the royal ammunition factory of Eugi (Spain)
(Technical Faculty, University of Belgrade, 2018) Zalakain Iriazabal, Iñaki; Berlanga Labari, Carlos; Álvarez Vega, Lucas; Rivero Fuente, Pedro J.; Valencia Monreal, Javier; Rodríguez Trías, Rafael; Mekanika, Energetika eta Materialen Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Mecánica, Energética y de Materiales
In this work, a comparative analysis of two iron bullets found in The Royal Ammunition Factory of Eugi in Navarra (Spain) was performed. Both bullets presented a spherical shape with a relatively good state of preservation, belonging to the last years of the factory production (1766-1850). Several techniques such as microhardness, X-ray fluorescence (XRF), light (LM) and scanning electron microscopy (SEM), optical mission spectroscopy (OES) and energy dispersive X-ray spectroscopy (EDX) analysis were used in order to identify the manufacturing process of the two bullets. The analyses of the microstructures carried out by LM and SEM showed that one bullet was composed of white cast iron with a pearlitic matrix, steadite and graphite; while the other was composed of grey cast iron with a pearlitic matrix, graphite and a low amount of steadite. The chemical analysis of the bullets carried out by OES indicated significant differences in the amount of silicon and phosphorous. The variation in silicon content could suggest that the foundry temperature under oxidizing environment varied during the casting. The SEM and EDX analyses showed both bullets had manganese sulphide inclusions but only one of the bullets exhibited titanium and vanadium inclusions. The microhardness analyses carried out revealed Vickers hardness differences along the diameter. This variation could be explained by the differences in cooling rate along the diameter. Based on the physical characteristics of the bullets and on the obtained results, it can be concluded that one of the bullets could have been used as a grapeshot projectile and the other one as a bullet for ribauldequins. In addition, calcined ore and slag found in this factory were also analysed. The variation found in their chemical composition corroborated that the foundry temperature employed during the manufacturing process was low, the slag being enriched in Si, Al and Mn elements.
Open Access
Estudio de la oxidación a elevada temperatura de ocho aleaciones en atmósferas de combustión de biomasa
(CENIM, 2008) Berlanga Labari, Carlos; Fernández Carrasquilla, Javier; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
La combustión de biomasa, especialmente de paja de cereal, genera un ambiente muy corrosivo, particularmente, cerca de los tubos sobrecalentadores. El cloro es el principal agente corrosivo en las plantas de biomasa. Este trabajo se centra en comprobar el comportamiento de ocho aleaciones comerciales en una ambiente de combustión de biomasa. Los materiales estudiados han sido las siguientes: AISI 347 CG (1.4550), AISI 347 FG (1.4550), AISI 316LN (1.4910), ESSHETE 1250 (1.4982), AC 66 (1.4877), X20CrMoV12:1 (1.4922) y AISI 347 recubiertos con Inconel 625 e Inconel 686. Los ensayos se han realizado en la caldera de la planta de biomasa de Sangüesa (Navarra, España) durante 8.000 y 15.000 h a una temperatura de 500-550 °C. Los resultados indican un buen comportamiento de los aceros inoxidables austeníticos y de las aleaciones de Inconel, mientras que el del acero martensítico no ha sido aceptable. Se ha propuesto el mecanismo conocido como “oxidación activa” para interpretar el comportamiento a la corrosión de estos materiales en estos medios.