Open Access
Effect of Ti on microstructure, mechanical properties and corrosion behavior of a nickel-aluminum bronze alloy
(ABM, ABC, ABPol, 2021-04-12) Rivero Fuente, Pedro J.; Berlanga Labari, Carlos; Palacio, José F.; Biezma Moraleda, María Victoria; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
Nickel-aluminum bronze (NAB) alloys are suitable, in cast condition, to be used in marine propellers due to its excellent behavior avoiding erosion and cavitation as well as corrosion. A complex microstructure, intrinsic to this copper base system, is the result of a well-controlled chemical composition. There are few works related to the effect of adding small quantities of specific chemical elements on NAB alloys properties. The aim of this paper is to study the effect of Ti on the microstructure, mechanical properties, and corrosion behavior of a particular NAB alloy, CuAl10Fe5Ni5 (C95500), and the comparison to the Ti-free NAB alloy. Although the as- cast microstructure is very similar for both materials, the addition of only 120 ppm Ti leads to a significant grain refinement that plays a key role on the mechanical properties. It has been observed an increase in both microhardness and nanohardness as well as in the resultant Young moduli values, meanwhile no significant impact on the corrosion susceptibility has been observed.
Open Access
Revisión y estado del arte de la corrosividad del etanol y sus mezclas con gasolina
(CENIM, 2011) Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Fernández Carrasquilla, Javier; Universidad Pública de Navarra. Departamento de Ingeniería Mecánica, Energética y de Materiales; Nafarroako Unibertsitate Publikoa. Mekanika, Energetika eta Materialen Ingeniaritza Saila
Actualmente, el etanol se presenta como una fuente importante de combustible renovable para el sector de la automoción. Se sabe que los carburantes tradicionales, como la gasolina, no han causado problemas de corrosión, debido principalmente a su baja miscibilidad en el agua. En cambio, los biocarburantes en base alcohol pueden contener una considerable cantidad de agua y, además, se puede producir la oxidación parcial de sus componentes por su exposición a la atmósfera. Estas reacciones pueden ocasionar corrosión y posterior fallo, de cualquier componente metálico en contacto con las mezclas etanol-gasolina. En consecuencia, todos los sectores relacionados con la industria que emplean este combustible, empresas productoras, logística, dispensadores y fabricantes de vehículos, pueden estar afectados por esta problemática. Esto hace que este tema sea muy interesante, tanto desde un punto de vista científico como industrial. En este trabajo se revisa sistemáticamente todos los aspectos relacionados con la corrosión que produce el etanol y sus mezclas con gasolina, con el objetivo de conocer en profundidad el estado actual de las investigaciones, así como para orientar trabajos futuros que estén afectados, tanto de forma directa o indirecta con esta temática.
Open Access
Study of the degradation of heat exchanger materials in the acidic environment of Teide National Park
(2019) Catalán Ros, Leyre; Pérez Artieda, Miren Gurutze; Berlanga Labari, Carlos; Garacochea Sáenz, Amaia; Rodríguez García, Antonio; Domínguez, Vidal; Montañez, Ana Carolina; Padilla, Germán D.; Pérez, Nemesio M.; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Ingeniería
Supplying power to volcanic monitoring stations constitutes a challenge due to both the access difficulties and the acidic environment associated with volcanoes. ELECTROVOLCAN project is developing thermoelectric generators that make use of the temperature of the available fumaroles to directly supply electricity to the stations in a robust, compact and reliable way. The main element of thermoelectric generators are the thermoelectric modules, based on Seebeck effect. Nonetheless, since the efficiency of these modules increases with the temperature difference between their sides, the introduction of heat exchangers becomes essential. The present study analyses the behavior of different materials used in the construction of the heat exchangers in the acidic environment of Teide National Park.
Open Access
Relationship between microstructure and fracture types in a UNS S32205 duplex stainless steel
(ABM, ABC, ABPol, 2013) Biezma Moraleda, María Victoria; Berlanga Labari, Carlos; Argandoña Salinas, Gorka; Ingeniería Mecánica, Energética y de Materiales; Mekanika, Energetika eta Materialen Ingeniaritza
Duplex stainless steels are susceptible to the formation of sigma phase at high temperature which could potentially be responsible for catastrophic service failure of components. Thermal treatments were applied to duplex stainless steels in order to promote the precipitation of different fractions of sigma phase into a ferrite-austenite microstructure. Quantitative image analysis was employed to characterize the microstructure and Charpy impact tests were used in order to evaluate the mechanical degradation caused by sigma phase presence. The fracture morphology of the Charpy test specimens were thoroughly observed in SEM, looking for a correlation between the microstructure and the fracture types in UNS S32205 duplex stainless steel. The main conclusion is the strong embrittlement effect of sigma phase since it is possible to observe a transition from transgranular fracture to intergranular fracture as increases the percentage of sigma phase. Thus, the mixed modes of fracture are predominant in the present study with high dependence on sigma phase percentages obtained by different thermal treatments.
Open Access
Corrosion behavior in volcanic soils: in search of candidate materials for thermoelectric devices
(MDPI, 2021-12-21) Berlanga Labari, Carlos; Catalán Ros, Leyre; Palacio, José F.; Pérez Artieda, Miren Gurutze; Astrain Ulibarrena, David; Ingeniaritza; Institute of Smart Cities - ISC; Ingeniería; Institute for Advanced Materials and Mathematics - INAMAT2
Thermoelectric generators have emerged as an excellent solution for the energy supply of volcanic monitoring stations due to their compactness and continuous power generation. Nevertheless, in order to become a completely viable solution, it is necessary to ensure that their materials are able to resist in the acidic environment characteristic of volcanoes. Hence, the main objective of this work is to study the resistance to corrosion of six different metallic materials that are candidates for use in the heat exchangers. For this purpose, the metal probes have been buried for one year in the soil of the Teide volcano (Spain) and their corrosion behavior has been evaluated by using different techniques (OM, SEM, and XRD). The results have shown excessive corrosion damage to the copper, brass, and galvanized steel tubes. After evaluating the corrosion behavior and thermoelectric performance, AISI 304 and AISI 316 stainless steels are proposed for use as heat exchangers in thermoelectric devices in volcanic environments.
Open Access
Effect of the temperature in the mechanical properties of austenite, ferrite and sigma phases of duplex stainless steels using hardness, microhardness and nanoindentation techniques
(MDPI, 2017) Argandoña Salinas, Gorka; Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Rivero Fuente, Pedro J.; Peña, Julio; Rodríguez Trías, Rafael; Mekanika, Energetika eta Materialen Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería Mecánica, Energética y de Materiales
The aim of this work is to study the hardness of the ferrite, austenite and sigma phases of a UNS S32760 superduplex stainless steel submitted to different thermal treatments, thus leading to different percentages of the mentioned phases. A comparative study has been performed in order to evaluate the resulting mechanical properties of these phases by using hardness, microhardness and nanoindentation techniques. In addition, optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD) have been also used to identify their presence and distribution. Finally, the experimental results have shown that the resulting hardness values were increased as a function of a longer heat treatment duration which it is associated to the formation of a higher percentage of the sigma phase. However, nanoindentation hardness measurements of this sigma phase showed lower values than expected, being a combination of two main factors, namely the complexity of the sigma phase structure as well as the surface finish (roughness).
Open Access
Corrosion of cast aluminum alloys: a review
(MDPI, 2020-10-16) Berlanga Labari, Carlos; Biezma Moraleda, María Victoria; Rivero Fuente, Pedro J.; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
Research on corrosion resistance of cast aluminum alloys is reviewed in this article. The effect of the main microstructural features of cast aluminum alloys such as secondary dendrite arm spacing (SDAS), eutectic silicon morphology, grain size, macrosegregation, microsegregation, and intermetallic compounds is discussed. Moreover, the corrosion resistance of cast aluminum alloys obtained by modern manufacturing processes such as semi-solid and additive manufacturing are analyzed. Finally, the protective effects provided by different coatings on the aluminum cast alloys—such as anodized, plasma electrolytic oxidation (PEO), and laser—is reviewed. Some conclusions and future guidelines for future works are proposed.
Open Access
Functionalized electrospun fibers for the design of novel hydrophobic and anticorrosive surfaces
(MDPI, 2018) Rivero Fuente, Pedro J.; Yurrita Silanes, David; Berlanga Labari, Carlos; Rodríguez Trías, Rafael; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, Navarre-PRO-UPNA18 (6107)
In this work, a novel coating was deposited on aluminum alloy samples by using a combination of electrospinning and chemical vapor deposition (CVD-silanization) techniques in order to create a functionalized film with an enhancement of both corrosion resistance and hydrophobicity. The electrospinning technique makes the fabrication of highly crosslinked electrospun fibers possible by the combination of both poly(acrylic acid) and beta-cyclodextrin, respectively, which can be easily functionalized in a further step by using the CVD-silanization process due to the evaporation of a hydrophobic molecule such as 1H,1H,2H,2H-Perflurodecyltriethoxysilane. In addition, the resultant electrospun fibers with a high degree of insolubility have been successfully fabricated and metal oxide nanoparticles (TiO(2)NPs) have been incorporated into the electrospun polymeric solution in order to improve the corrosion protection. The surface morphology has been determined by using light optical microscopy, atomic force microscopy, scanning electron microscopy, and water contact angle (WCA) measurements. The corrosion resistance has been evaluated by using both potentiodynamic polarization and pitting corrosion tests. Finally, the results related to WCA measurements after CVD-silanization corroborate that the surfaces have been successfully functionalized with a hydrophobic behavior in comparison with the electrospinning process, showing a considerable difference in the roughness.
Open Access
A comprehensive review of fatigue strength in pure copper metals (DHP, OF, ETP)
(MDPI, 2024) Jiménez Ruiz, Eduardo; Lostado Lorza, Rubén; Berlanga Labari, Carlos; Ingeniería; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2
Due to their exceptional electrical and thermal conductivity properties, high-purity copper (Cu-DHP) and copper alloys of similar composition, such as electrolytic tough-pitch (ETP), oxygen-free electronic (OFE) and oxygen-free (OF), have often been used in the manufacture of essential components for the electrical, electronic and power generation industries. Since these components are subject to cyclic loads in service, they can suffer progressive structural damage that causes failure due to fatigue. The purpose of this review is to examine the most relevant aspects of mechanical fatigue in Cu-DHP, ETP, OFE and OF. The impact of many factors on fatigue strength (Se), including the frequency, temperature, chemical environment, grain size, metallurgical condition and load type, were analyzed and discussed. Stress–life (S-N) curves under zero mean stress (σm = 0) were found for high-cycle fatigue (HCF). For non-zero mean stress (σm ≠ 0), stress curves were based on a combination of Gerber, Soderberg and ASME elliptic failure criteria. Stress–life (S-N) curves were also developed to correlate fatigue strength (Se) with stress amplitude (σa), yield strength (Syp) and ultimate strength (Sut). Finally, for low-cycle fatigue (LCF), strain–life (ε-N) curves that establish a relationship between the number of cycles to failure (N) and total strain amplitude (εplastic) were determined. Hence, this review, as well as the proposed curves, provide valuable information to understand fatigue failure for these types of materials.
Open Access
Comparative study of the metallurgical quality of primary and secondary AlSI10MnMg aluminium alloys
(MDPI, 2021) Bakedano, Asier; Niklas, Andrea; Fernández‐Calvo, Ana Isabel; Plata, Gorka; Lozares, Jokin; Berlanga Labari, Carlos; Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Ingeniería
The use of secondary aluminium is increasingly being promoted in the automotive industry for environmental reasons. The purpose of this study was to demonstrate that it is possible to obtain a recycled AlSi10MnMg(Fe) aluminium alloy with equal metallurgical quality to that of a primary AlSi10MnMg alloy when an adequate melt treatment is applied. The melt treatment consisted of deoxidation, degassing and skimming in accordance with the detailed procedure described in this article. The metallurgical qualities of one primary and two secondary alloys were assessed using thermal analysis, the density index test, the macroinclusion test and the microinclusion level test before and after melt treatment. The thermal analysis allowed us to compare the variables of the solidification cooling curve (Al primary temperature and its undercooling; Al‐Si eutectic temperature and its predictive modification rate). The density index test was used to evaluate the hydrogen gas content in the melt. The macroinclusion test was used to evaluate the melt cleanliness, while the microinclusion level test was used to perform the inclusion identification and quantification analyses. This study showed the feasibility of manufacturing structural components using 100% recycled secondary aluminium alloy through V‐ HPDC technology.