Open Access
Temperature indicators and overtemperature detection in lithium-ion batteries based on electrochemical impedance spectroscopy
(IEEE, 2023) Lalinde Sainz, Iñaki; Berrueta Irigoyen, Alberto; Soto Cabria, Adrián; Arza, Joseba; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lithium-ion batteries are the leading technology for energy storage systems due to their attractive advantages. However, the safety of lithium-ion batteries is a major concern, as their operating conditions are limited in terms of temperature, voltage and state of charge. Therefore, it is important to monitor the conditions of lithium-ion batteries to guarantee safe operation. To this end, in the present work, we analyze electrochemical impedance spectroscopy (EIS) as a tool to estimate the temperature of batteries. Overtemperature abuse tests from 25 °C to 140 °C are performed at various states of charge, and EIS measurements are obtained during the tests. The influence of temperature on cell impedance at different frequencies is analyzed and new findings are revealed. The real part of the impedance is identified to be the best indicator for cell temperature estimation by EIS. In addition, the best frequency to achieve accurate temperature monitoring, avoiding disturbances produced by state of charge variations, is proposed based on experimental results. Finally, EIS is proven to be a reliable technique for overtemperature and thermal runaway detection.
Open Access
Methodology for comparative assessment of battery technologies: experimental design, modeling, performance indicators and validation with four technologies
(Elsevier, 2025-01-15) Irujo Izcue, Elisa; Berrueta Irigoyen, Alberto; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, PJUPNA2023-11380; Gobierno de Navarra / Nafarroako Gobernua
An increasing number of applications with diverse requirements incorporate various battery technologies. Selecting the most suitable battery technology becomes a tedious task as several aspects need to be taken into account. Two of the key aspects are the battery characteristics under temperature variations and their degradation. While numerous contributions using tailored assessment methods to evaluate both aspects for a particular application exist in the literature, a general methodology for analysis is necessary to enable a quantitative comparison between different technologies. We propose in this paper a novel methodology, based on performance indicators, to quantify the potential and limitations of a battery technology for diverse applications sharing a similar operational profile. A quantification of phenomena such as the influence of high and low temperatures on the battery, or the effect of cycling and state of charge on battery aging is obtained. In pursuit of these indicators, an experimental procedure and the fitting of aging model parameters that allow their calculation are proposed. As an additional outcome of this work, a general aging model that allows comprehensive analysis of aging behavior is developed and the trade-off between experimental time and accuracy is analyzed to find an optimal experimental time between 2 and 4 months, depending on the studied battery technology. Finally, the proposed methodology is applied to four battery technologies in order to show its potential in a real case-study.
Open Access
Influence of renewable power fluctuations on the lifetime prediction of lithium-ion batteries in a microgrid environment
(IEEE, 2019) Soto Cabria, Adrián; Berrueta Irigoyen, Alberto; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Gobierno de Navarra / Nafarroako Gobernua
This contribution analyses lifetime estimation errors due to the effect of power fluctuations in lithium-ion batteries connected to microgrids when different time steps are used for the calculations. Usually, not every second data are available or the computational cost is excessively high. Those facts result in the use of larger time steps. However, the increase of the time steps may turn out in too optimistic predictions. Data from a real microgrid make it possible to optimize calculation times while keeping low errors. The results show that when 1 minute time step is set, the computation time is reduced by 14.4 times while the lifetime overstatement is only 3.5-5.2% higher, depending on the aging model.
Open Access
Energy storage systems based on lithium-ion batteries and supercapacitors: characterization, modelling and integration with renewable energies
(2017) Berrueta Irigoyen, Alberto; Ursúa Rubio, Alfredo; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa; Gobierno de Navarra / Nafarroako Gobernua
Los inconvenientes medioambientales, sociales y económicos que presentan los combustibles fósiles y nucleares están propiciando un uso cada vez mayor de fuentes de energía renovables. El fuerte desarrollo tecnológico de los sistemas de generación basados en estas fuentes de energía, especialmente de los sistemas eólicos y fotovoltaicos, ha abaratado enormemente sus costes de producción, resultando ya tecnologías competitivas en relación con las plantas convencionales. Actualmente, el principal obstáculo que limita su integración masiva en la red eléctrica es su gestionabilidad, dada la naturaleza intermitente del recurso renovable. Los sistemas de almacenamiento energético distribuidos, y en particular las baterías de litio y los supercondensadores, surgen como una de las mejores alternativas para mejorar la gestión de esta energía y facilitar la operación de una red el ectrica cada vez más basada en sistemas renovables. Esta tesis analiza en profundidad ambas tecnologías de almacenamiento, especialmente cuando funcionan en entornos de generación renovable. Las principales líneas de trabajo de la tesis son: Análisis del estado actual de las tecnologías; Estudio de la influencia de los fenómenos termodinámicos, electroquímicos y térmicos en el funcionamiento de estos sistemas de almacenamiento; Modelado electroquímico y térmico de ambas tecnologías de almacenamiento; Estimación del estado de carga y del envejecimiento en baterías de litio; Validación experimental de los modelos propuestos ante diferentes condiciones de funcionamiento; Desarrollo de metodologías para el diseño y funcionamiento óptimo de sistemas de almacenamiento basados en baterías de litio en entornos renovables y particularización para centrales fotovoltaicas.
Open Access
New design alternatives for a hybrid photovoltaic and doubly-fed induction wind plant to augment grid penetration of renewable energy
(IEEE, 2021) Goñi, Naiara; Sacristán Sillero, Javier; Berrueta Irigoyen, Alberto; Rodríguez Rabadan, José Luis; Ursúa Rubio, Alfredo; Sanchis Gúrpide, Pablo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Reducing carbon emissions is essential to stop climate change. The grid-share of renewable generation plants is increasing, being wind and photovoltaic plants the most common ones, whereas conventional plants are the only ones that provide the necessary services to maintain the grid stability and keep the generation-demand balance. However, with the aim of achieving carbon-neutral generation, conventional plants are being dismantled. This leads to the imminent need of providing these services with renewable plants. Due to this challenge, this proposal analyses a hybrid plant composed by wind and photovoltaic generation with two types of storage, lithium-ion batteries and a thermal storage system based on volcanic stones. In order to compare both strategies, a technoeconomic methodology is explained that allows to optimally size the plant, using the current prices of each technology. The most cost-competitive proposal turns to be the hybrid plant with thermal storage, composed by 623.9 MW installed power and 21.9 GWh of storage, which could replace a 100 MW, 24/7 conventional power plant, with an LCOHS (levelized cost of hybrid system) of 118.38 €/MWh, providing identical grid services and an equivalent inertia in a way committed with the environment. This is in turn a zero-carbon emissions solution perfectly matched to a second life plan for a conventional power plant.
Open Access
Identification of critical parameters for the design of energy management algorithms for Li-ion batteries operating in PV power plants
(IEEE, 2020) Berrueta Irigoyen, Alberto; Soto Cabria, Adrián; Marcos Álvarez, Javier; Parra Laita, Íñigo de la; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa, ReBMS PJUPNA1904; Gobierno de Navarra / Nafarroako Gobernua, 0011-1411-2018-000029 GERA
Lithium-ion batteries are gaining importance for a variety of applications due to their price decrease and characteristics improvement. For a proper use of such storage systems, an energy management algorithm (EMA) is required. A number of EMAs, with various characteristics, have been published recently, given the diverse nature of battery problems. The EMA of deterministic battery problems is usually based on an optimization algorithm. The selection of such an algorithm depends on a few problem characteristics, which need to be identified and closely analyzed. The aim of this article is to identify the critical optimization problem parameters that determine the most suitable EMA for a Li-ion battery. With this purpose, the starting point is a detailed model of a Li-ion battery. Three EMAs based on the algorithms used to face deterministic problems, namely dynamic, linear, and quadratic programming, are designed to optimize the energy dispatch of such a battery. Using real irradiation and power price data, the results of these EMAs are compared for various case studies. Given that none of the EMAs achieves the best results for all analyzed cases, the problem parameters that determine the most suitable algorithm are identified to be four, i.e., desired computation intensity, characteristics of the battery aging model, battery energy and power capabilities, and the number of optimization variables, which are determined by the number of energy storage systems, the length of the optimization problem, and the desired time step.
Open Access
Applied method to model the thermal runaway of lithium-ion batteries
(IEEE, 2021) Lalinde Sainz, Iñaki; Berrueta Irigoyen, Alberto; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The thermal runaway (TR) is one of the most dangerous phenomena related to lithium-ion batteries. For this reason, there are different proposals in the literature for its modelling. Most of these proposed models take into account the decomposition reactions between the internal components of the cell, and base the adjustment of the parameters on numerous abuse tests that lead to the appearance of TR. However, these tests are destructive, require specific equipment, present a high economic cost and are very time consuming. This paper proposes a modelling method which enables the development of TR models with the use of fewer resources. This method is based on chemical kinetics, which allow a simplification of the general modelling process published in the literature. At the same time it maintains good accuracy and makes it possible to define the TR behavior of any type of cell, regardless of its chemistry, shape or size. Furthermore, the proposed method allows the use of the experimental results most commonly presented in the specialized literature, which significantly reduces the need for destructive testing. The presented modelling method achieves a good compromise between accuracy and applicability in the validations shown in the paper.
Open Access
Onset of irreversible reactions in overcharging lithium-ion cells: an experimental and modeling approach
(IEEE, 2023) Irujo Izcue, Elisa; Berrueta Irigoyen, Alberto; Lalinde Sainz, Iñaki; Arza, Joseba; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Lithium-ion batteries are energy storage systems used in an increasing number of applications. Due to their flammable materials, their use entails risks of fire and explosion. The study of the abuse operation of these batteries before reaching the thermal runaway is a relevant research topic to prevent safety issues. There are various studies in the bibliography providing exhaustive thermal studies of the safe operating area, as well as concerning the thermal runaway. However, the onset irreversible reactions, that take place at a SOC around 110%, have not been properly analyzed. We present in this contribution an experimental study of this onset reaction measured in pouch Li-ion cells under various conditions of charge current and temperature. We also propose a lumped-parameter thermal model for the cell, which allows a detailed characterization of this exothermic reaction. The results achieved in this contributions can be a key tool to prevent overcharge accidents that may arise due to malfunctioning of the battery charger or battery management system.
Open Access
Hydrogen-based energy storage for a distributed generation system
(Spanish Hydrogen Association, 2016) San Martín Biurrun, Idoia; Berrueta Irigoyen, Alberto; Ursúa Rubio, Alfredo; Sanchis Gúrpide, Pablo; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute of Smart Cities - ISC
One of the most typical distributed generation systems are electrical microgrid, which consist on small electrical grids, generally connected to the main grid, with a decentralized management structure. Electrical microgrids allow higher renewable energy integration in the grid, achieving a cost decrease and improving the grid quality [1]. These mi- crogrids incorporate renewable generation systems and energy consumers. Moreover, they have storage systems to balance generation and consumption as well as the exchanged power with the main grid. Traditionally, lead-acid batter- ies have been used in microgrids. However, these batteries have some drawbacks, being the most important its poor performance in partial state of charge, which is critical for a microgrid. A suitable option for the storage system is hy- drogen technology. These systems have high energy density, which makes the storage system able to assume seasonal variability of renewable resources. This paper proposes a sizing methodology for storage systems based on hydrogen for grid-tied electrical microgrids. This methodology optimizes the relationship between the storage system size and the consumption of grid power.
Open Access
Impact of micro-cycles on the lifetime of lithium-ion batteries: an experimental study
(Elsevier, 2022) Soto Cabria, Adrián; Berrueta Irigoyen, Alberto; Mateos Inza, Miren; Sanchis Gúrpide, Pablo; Ursúa Rubio, Alfredo; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa Gobierno de Navarra / Nafarroako Gobernua
Experimental aging studies are commonly conducted on lithium-ion batteries by full charge and discharge cycles. However, such profiles may differ from the actual operation of batteries in electric vehicles and stationary applications, where they are subjected to different partial charges and discharges. These partial cycles, which take place during a main charge or discharge process, are called micro-cycles if their depth of discharge is <2 %. A number of authors have pointed out the relevance of the time resolution to estimate the energy throughput of a battery due to these micro-cycles in applications such as renewable microgrids. However, to the best of our knowledge, there are no experimental studies in the literature that assess the impact of these micro-cycles on battery degradation. In this article, the impact of micro-cycles on the loss of performance of a lithium-ion battery is experimentally studied. The results show that micro-cycles have a negligible, or even positive effect on the aging of lithium-ion cells compared to the aging caused by full cycles. In fact, if charge throughput or equivalent full cycles are used to measure the use of a battery, then cells subjected to micro-cycles exhibit a 50 % extended lifetime compared to cells only subjected to full cycles. More precisely, cells including micro-cycles with depth of discharge of 0.5 % lasted for nearly 3000 equivalent full cycles, whereas cells aged under standard deep cycles lasted for no >1500. Nevertheless, if the number of deep cycles, disregarding micro-cycles, is the unit to measure battery use, then the degradation of cells with and without micro-cycles is similar. Based on this result, the number of cycles can be identified as a more accurate variable to measure the use of a cell, in comparison to charge throughput.