Open Access
Magnetically activated 3D printable polylactic acid/polycaprolactone/magnetite composites for magnetic induction heating generation
(Springer, 2023) Galarreta Rodríguez, Itziar; López Ortega, Alberto; Garayo Urabayen, Eneko; Beato López, Juan Jesús; La Roca, Paulo Matías; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
Additive manufacturing technology has attracted the attention of industrial and technological sectors due to the versatility of the design and the easy manufacture of structural and functional elements based on composite materials. The embedding of magnetic nanoparticles in the polymeric matrix enables the development of an easy manufacturing process of low-cost magnetically active novel polymeric composites. In this work, we report a series of magnetic composites prepared by solution casting method combining 5 to 60 wt.% of 140 ± 50 nm commercial Fe3O4 nanoparticles, with a semi-crystalline, biocompatible, and biodegradable polymeric blend made of polylactic acid (PLA) and polycaprolactone (PCL). The composites were extruded, obtaining 1.5 ± 0.2 mm diameter continuous and flexible filaments for fused deposition modelling 3D printing. The chemical, magnetic, and calorimetric properties of the obtained filaments were investigated by differential scanning calorimetry, thermogravimetric analysis, magnetometry, and scanning electron microscopy. Furthermore, taking advantage of the magnetic character of the filaments, their capability to generate heat under the application of low-frequency alternating magnetic fields (magnetic induction heating) was analyzed. The obtained results expose the versatility of these easy manufacturing and low-cost filaments, where selecting a desired composition, the heating capacity can be properly adjusted for those applications where magnetic induction plays a key role (i.e., magnetic hyperthermia, drug release, heterogeneous catalysis, water electrolysis, gas capture, or materials synthesis).
Open Access
Fast calculation methods for the magnetic field of particle lattices
(AIP Publishing, 2025-02-14) Royo Silvestre, Isaac; Gandía Aguado, David; Beato López, Juan Jesús; Garayo Urabayen, Eneko; Gómez Polo, Cristina; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika
With the rise of 3D printing and composite materials, components comprising dispersed magnetic particles have become more interesting due to the possibility to design magnetic elements of any shape with varying amounts of the actual magnetic material. However, quick and easy calculation methods are needed to design these components enabling the selection of the optimum required percentage of magnetic particles (millimeter parts contain billions of micro-sized particles). This work proposes a semi-analytical iterative method for the estimation of the magnetic field generated by magnetic composites formed by embedded magnetic particles. The model is compared in terms of accuracy and calculation speed with finite element analysis and the average magnetization model of the magnetic composite. The results are finally supported by the comparison with experimental measurements of the weak magnetic field generated by a magnetic particle lattice.
Open Access
U-shape magnetostrictive harvester: design and experimental validation
(IEEE, 2024-07-05) Gandía Aguado, David; Garayo Urabayen, Eneko; Beato López, Juan Jesús; Royo Silvestre, Isaac; Gómez Polo, Cristina; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
Electromagnetic vibrational harvesters stand out due to their high-power density, long-life robust structure and low-cost design. Moreover, they can be designed using magnetostrictive materials. The mechanical vibrations cause stress on the magnetostrictive material, leading to variations in its magnetization. This, in turn, induces an electromotive force (EMF) in a well-designed pick-up coil system, thereby transforming mechanical energy into electrical energy. In spite of the potentiality of these electromagnetic harvesters, their practical implementation is limited due to the difficulties in the design optimization in terms of the device dimensions, effective stresses on the magnetostrive material, distribution and magnetic field strength of the permanent magnets and pick-up coil characteristics. Finite Element Methods (FEM) enable the estimation of the induced voltage and thus the output power as a function of harvester design parameters, allowing us to experiment with different configurations and identify optimal parameters.
Open Access
Modulating photocatalytic activity of nitrogen doped TiO2 nanoparticles via magnetic field
(Elsevier, 2024-07-30) Gómez Polo, Cristina; Cervera Gabalda, Laura María; Garayo Urabayen, Eneko; Beato López, Juan Jesús; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The effect of the magnetic field on the photocatalytic activity of TiO2-based nanoparticles is analyzed using a magnetically-assisted photoreactor with permanent magnets to generate a controlled uniform magnetic field, B (¿82 mT). Nitrogen doped TiO2 nanoparticles (sizes around 10 nm) were synthesized through a solvothermal method employing Ti(IV) butoxide and HNO3 (x = 0, 0.5, 1, 1.5 and 2 mL) as precursors and their structural, optical and magnetic properties were analyzed. Specifically, nitrogen doping is confirmed through Hard X-ray Photoelectron Spectroscopy (HAXPES) in those samples synthesized with low HNO3 concentrations (x = 0.5, 1). The correlation between spin polarization (magnetic susceptibility) and visible photocatalytic activity (methyl orange as a model organic pollutant) is particularly analyzed. Surprisingly, opposite effects of the magnetic field on the photocatalytic performance are found in the visible range (above 400 nm) or under UV-Vis irradiation (decrease and increase in the photocatalytic activity, respectively, under magnetic field). The Langmuir-Hinshelwood model allows us to conclude that the strong decrease in adsorption under the magnetic field (around 42 % for x = 0.5) masks the increase in the kinetic constant (close to 58 % for x = 0.5) related mainly to the effect of Lorentz forces on the reduction of the electron-hole recombination.
Open Access
Magnetic-field-assisted photocatalysis of N-TiO2 nanoparticles
(IEEE, 2023-09-04) Cervera Gabalda, Laura María; Garayo Urabayen, Eneko; Beato López, Juan Jesús; Pérez de Landazábal Berganzo, José Ignacio; Gómez Polo, Cristina; Ciencias; Zientziak; Institute for Advanced Materials and Mathematics - INAMAT2
Nitrogen doped TiO2 nanoparticles were synthesized through solvothermal method employing Ti (IV) butoxide and HNO3 as precursors. Structural and optical characterizations confirm their nanometer nature (sizes around 10 nm) and the band-gap energy values in the UV range (3.2 eV). Nitrogen doping enhances the occurrence of optical Urbach tails extending towards the visible region. Visible photocatalytic performance (degradation of methyl orange) is correlated with maximum values in the magnetic susceptibility linked to a magnetic polarization of the anatase structure via defects (oxygen vacancies). The application of magnetic field provides a positive effect (acceleration in reaction kinetics) within the UV-Vis range.
Open Access
Electromagnetic vibrational harvester based on U-shaped ferromagnetic cantilever: a novel two-magnet configuration
(Elsevier, 2024-09-07) Gandía Aguado, David; Garayo Urabayen, Eneko; Beato López, Juan Jesús; Royo Silvestre, Isaac; Cruz Blas, Carlos Aristóteles de la; Tainta Ausejo, Santiago; Gómez Polo, Cristina; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Estadística, Informática y Matemáticas; Estatistika, Informatika eta Matematika; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC
Electromagnetic vibrational harvesters are low-cost devices featuring high-power densities and robust structures, often used for capturing the energy of environmental vibrations (civil infrastructures, transportation, human motion, etc.,). Based on Faraday's law, energy generation relies on the modification of the magnetic field distribution within a magnetic element caused by mechanical vibrations inducing an electromotive force (EMF) in a pick-up coil. However, the practical implementation of this type of vibrational harvester is currently limited due to the reduced generated power under low-frequency vibrations. In this work, an electromagnetic vibrational harvester is experimentally characterized and analyzed employing magnetic circuit analysis. The harvester consists of a ferromagnetic U-shaped cantilever, a NdFeB magnet and a ferrite magnet used as ¿magnetic tip mass¿ to enhance the magnetic flux changes under vibrations of frequency < 100 Hz. For this configuration, an experimental voltage of ¿ 1.2 V peak-to-peak (open circuit) was obtained at a resonant frequency of 77 Hz, enabling the subsequent electronic rectification stage. Additionally, Finite Element Method (FEM) is used to explore different design possibilities including the modeling of complex geometries, mechanical properties and non-linear magnetic materials, enabling the tuning of the resonance frequency from 51 to 77 Hz, keeping constant the induced voltage.
Open Access
Monitoring structural transformations in metamagnetic shape memory alloys by non-contact GMI technology
(IOP Publishing, 2023) Beato López, Juan Jesús; La Roca, Paulo Matías; Algueta-Miguel, Jose M.; Garayo Urabayen, Eneko; Sánchez-Alarcos Gómez, Vicente; Recarte Callado, Vicente; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Different applications based on metamagnetic shape memory alloy (MSMA) require monitoring the evolution of the martensitic transformation (MT) to optimize the actuation mechanism. To avoid interaction with the active material, a non-contact technique would be ideal. Nevertheless, non-contact detection involves complex methods like diffraction, optical analysis, or electromagnetic technology. The present work demonstrates that the MT can be monitored without interaction with the active material using a low-cost technology based on the Giant Magnetoimpedance (GMI) effect. The GMI sensor is based on a (CoFe)SiB soft magnetic wire submitted to an alternating current and whose second harmonic voltage variation allows to detect changes in the strength of the stray magnetic fields linked to the metamagnetic phase transition. The sensor has been tested using the MT of a NiMnInCo MSMA. A specific application for environmental temperature control using the non-contact GMI sensor is proposed.
Open Access
Magnetic binary encoding system based on 3D printing and GMI detection prototype
(Elsevier, 2022) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; López Ortega, Alberto; Garayo Urabayen, Eneko; Gómez Polo, Cristina; Aresti Bartolomé, Maite; Soria Picón, Eneko; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Zientziak; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoa eta Telekomunikazio Ingeniaritza; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Gobierno de Navarra / Nafarroako Gobernua; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
In this work, the feasibility of a magnetic binary encoding system using 3D printing technology is analyzed. The study has a double interest, that is, the possibility of printing a 3D piece that contains the codified information and the development of a system for its decoding. For this purpose, magnetic nanoparticles (magnetite Fe3O4) were embedded in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL). Similar to a conventional barcode, a rectangular piece with an alternating pattern of strips with absence (only polymer) and a 5 wt% of embedded magnetic nanoparticles was 3D printed employing the Fused Deposition Modelling tech- nique (FDM). The information was decoded by means of a Giant Magnetoimpedance (GMI) sensor-based pro- totype, by scanning the surface of the piece and measuring the changes in the magnetic field. As sensor nucleus, an amorphous soft magnetic wire of nominal composition (Co0.94 Fe0.06)72.5 Si12.5 B15 was employed. The decoding prototype incorporates a homemade electronic sensor interface that permits, at the time, the GMI sensor excitation and the subsequent signal conditioning to optimize its response. The output signal enables the detection of the magnetite nanoparticles and the magnetic decoding of the encoded information (“1” and “0”, presence or absence of the magnetic nanoparticles, respectively).
Open Access
Non-linear GMI decoding in 3D printed magnetic encoded systems
(Elsevier, 2023) Beato López, Juan Jesús; Algueta-Miguel, Jose M.; Galarreta Rodríguez, Itziar; Garayo Urabayen, Eneko; López Ortega, Alberto; Gómez Polo, Cristina; Pérez de Landazábal Berganzo, José Ignacio; Ciencias; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute for Advanced Materials and Mathematics - INAMAT2; Institute of Smart Cities - ISC; Zientziak; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Universidad Pública de Navarra / Nafarroako Unibertsitate Publikoa
The nonlinear giant magnetoimpedance (GMI) effect was explored as a highly sensitive sensing technology in 3D-printed magnetic encoded systems. Magnetic nanoparticles with low (magnetite, Fe3O4) and high (Co ferrite, Co0.7Fe2.3O4) magnetic remanence were embedded (10 wt%) in a polymeric matrix of Polylactic Acid (PLA) and Poly-ε-caprolactone (PCL) and extruded in magnetic filaments to be 3D printed by the Fused Deposition Modelling technique (FDM). Two different geometries were constructed namely, individual magnetic strips and fixed barcoded pieces. The stray magnetic fields generated by the magnetic nanoparticles were detected through the non-linear (second harmonic) GMI voltage using a soft magnetic CoFeSiB wire as the nucleus sensor. The decoding response was analyzed as a function of the magnetization remanence of the nanoparticles, the distance between the individual magnetic strips, and the position (height) of the GMI decoding sensor. It has been shown that modification of the net magnetization direction of each individual fixed strip within the barcode geometry is possible through the application of local external magnetic fields. This possibility improves the versatility of the 3D binary encoding system by adding an additional state (0 without nanoparticles, 1 or −1 depending on the relative orientation of the net magnetization along the strips) during the codifying procedure.