Open Access
Impact of graphene monolayer on the performance of non-conventional silicon heterojunction solar cells with moox hole-selective contact
(MDPI, 2023) Ros, Eloi; Fernández, Susana; Ortega, Pablo; Taboada, Elena; Arnedo Gil, Israel; Gandía, José Javier; Voz, Cristóbal; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this work, a new design of transparent conductive electrode based on a graphene monolayer is evaluated. This hybrid electrode is incorporated into non-standard, high-efficiency crystalline silicon solar cells, where the conventional emitter is replaced by a MoOx selective contact. The device characterization reveals a clear electrical improvement when the graphene monolayer is placed as part of the electrode. The current–voltage characteristic of the solar cell with graphene shows an improved FF and Voc provided by the front electrode modification. Improved conductance values up to 5.5 mS are achieved for the graphene-based electrode, in comparison with 3 mS for bare ITO. In addition, the device efficiency improves by around 1.6% when graphene is incorporated on top. These results so far open the possibility of noticeably improving the contact technology of non-conventional photovoltaic technologies and further enhancing their performance.
Open Access
Integrating multiple stubs in stepped-impedance filter aiming for high selectivity
(IET, 2022) Sami, Abdul; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Arnedo Gil, Israel; Calero Fernández, Ibai; Teberio Berdún, Fernando; Martín Iglesias, Petronilo; Benito Pertusa, David; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
A design technique to include multiple and fully-controlled transmission zeros (TZs) in the frequency response of rectangular waveguide commensurate-line stepped-impedance filters is presented in this letter. These bandpass filters (BPFs) are known for having reduced sensitivities against manufacturing inaccuracies and are composed of multiple waveguide sections. In order to improve their selectivity, 3λg/4 and λg/4-stubs are included to create multiple TZs around the passband. The proposed technique allows us to add multiple stubs in a single section and, therefore, only minor adjustments in the affected part of the filter are required, which simplifies the overall design process. The technique has been verified with a design example with four TZs (two on each side) near the passband.
Open Access
Synthesis of one dimensional electromagnetic bandgap structures with fully controlled parameters
(IEEE, 2017) Arnedo Gil, Israel; Chudzik, Magdalena; Percaz Ciriza, Jon Mikel; Arregui Padilla, Iván; Teberio Berdún, Fernando; Benito Pertusa, David; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, we propose a novel synthesis strategy for the design of one dimensional electromagnetic bandgap (1- D-EBG) structures where all the performance parameters of these devices can fully be controlled, i.e., the central frequency of the forbidden band, its attenuation level and bandwidth, and the ripple level at the passbands. The novel synthesis strategy employs a new inverse-scattering technique to accurately synthesize the 1-D-EBG structure, targeting a properly interpolated version of a classical periodic filter fulfilling the required frequency specifications. The new inverse-scattering technique follows a continuous layer peeling approach and relies on the coupled-mode theory to precisely model the microwave structures. Telecommunication and radar systems, as well as material characterization devices, will be profited by this proposal with which enhanced filters, sensors, power dividers, couplers, mixers, oscillators, and amplifiers can be designed in many different technologies. As a proof of concept, a 1-D-EBG structure in microstrip technology with a single forbidden band (free of spurious stopband replicas), with attenuation level of 30 dB, fractional bandwidth larger than 100%, and return loss level at the passbands of 20 dB, has been designed and fabricated. The measurements obtained are in very good agreement with the simulations and target specifications, being free of spurious replicas up to the 15th harmonic, showing the robustness and very good performance of the novel design strategy proposed.
Open Access
Passive microwave component design using inverse scattering: theory and applications
(Hindawi, 2013) Arnedo Gil, Israel; Arregui Padilla, Iván; Chudzik, Magdalena; Teberio Berdún, Fernando; Lujambio Genua, Aintzane; Benito Pertusa, David; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
We briefly review different synthesis techniques for the design of passive microwave components with arbitrary frequency response, developed by our group during the last decade. We provide the theoretical foundations based on inverse scattering and coupledmode theory as well as several applications where the devices designed following those techniques have been successfully tested. The main characteristics of these synthesis methods are as follows. (a) They are direct, because it is not necessary to use lumpedelement circuit models; just the target frequency response is the starting point. (b)They are exact, as there is neither spurious bands nor degradation in the frequency response; hence, there is no bandwidth limitation. (c) They are flexible, because they are valid for any causal, stable, and passive transfer function; only inviolable physical principles must be guaranteed. A myriad of examples has been presented by our group in many different technologies for very relevant applications such as harmonic control of amplifiers, directional couplerwith enhanced directivity and coupling, transmission-type dispersive delay lines for phase engineering, compact design of high-power spurious free low-pass waveguide filters for satellite payloads, pulse shapers for advanced UWB radar and communications and for novel breast cancer detection systems, transmission-type Nth-order differentiators for tunable pulse generation, and a robust filter design tool.
Open Access
Multipactor breakdown analysis of Ku-band meandered low-pass filter
(2022) Sami, Abdul; Teberio Berdún, Fernando; Arnedo Gil, Israel; Martín Iglesias, Petronilo; Lopetegui Beregaña, José María; Gómez Laso, Miguel Ángel; Arregui Padilla, Iván; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren; Institute of Smart Cities - ISC; Ingeniería Eléctrica, Electrónica y de Comunicación
In this work, a very compact rectangular waveguide low-pass filter with meandered topology based on commensurate lines for Ku-band satellite applications is analysed for high-power handling capabilities. The device consists of rectangular waveguide sections properly cascaded to form a meandered topology to obtain the desired value of the local reflection coefficients. which are essential to achieve the target frequency response and also to keep large mechanical gaps. Hence, this technique allows us not only to design a filter with compact size but a filter geometry which is suitable for high power applications. In the paper, the low-pass filter based on commensurate lines is first designed by cascading E-plane mitered bends (±90° EMBs) in CST Microwave Studio (MWS) and then the values of the electromagnetic fields at the passband frequencies are exported to Spark3D to perform a multipactor analysis. The critical areas inside the device where the multipactor discharge occurs will also be identified in the high-power analysis. https://doi.org/10.5281/zenodo.7343236
Open Access
Mapping the conductivity of graphene with electrical resistance tomography
(Nature Research, 2019) Cultrera, Alessandro; Serazio, Danilo; Zurutuza, Amaia; Centeno, Alba; Txoperena, Ohiana; Etayo Salinas, David; Cordón, Álvaro; Redo Sánchez, Albert; Arnedo Gil, Israel; Ortolano, Massimo; Callegaro, Luca; Ingeniería Eléctrica, Electrónica y de Comunicación; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
Electronic applications of large-area graphene films require rapid and accurate methods to map their electrical properties. Here we present the first electrical resistance tomography (ERT) measurements on large-area graphene samples, obtained with a dedicated measurement setup and reconstruction software. The outcome of an ERT measurement is a map of the graphene electrical conductivity. The same setup allows to perform van der Pauw (vdP) measurements of the average conductivity. We characterised the electrical conductivity of chemical-vapour deposited graphene samples by performing ERT, vdP and scanning terahertz time-domain spectroscopy (TDS), the last one by means of a commercial instrument. The measurement results are compared and discussed, showing the potential of ERT as an accurate and reliable technique for the electrical characterization of graphene samples.
Open Access
Improvement of corona breakdown threshold (peak power handling) in smooth-profiled microstrip filters
(2022) Ahmad, Jamil; Hussain, Jabir; Arregui Padilla, Iván; Martín Iglesias, Petronilo; Arnedo Gil, Israel; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, the PPHCs of two filter design techniques, stepped-impedance (SI) and smooth-profile (SP), are presented for four design prototypes. Smooth-profiled filters feature smooth variations in the characteristic impedance profile, avoiding sharp edges, which accumulate electric fields. The absence of sharp edges in SP reduces the voltage magnification factor, which in turn improves the PPHC of the filter. The phenomenon of electric fields accumulation at the sharp corners of the SI filters is presented and compared with smooth transitions in SP filters. Furthermore, 1D graphs of electric field intensity are presented along the strip contour of the microstrip lines. Finally, SPARK3D results clearly demonstrate that SP filters can handle higher peak powers than their SI counterparts between critical pressure and ambient pressure, for all the studied designs.
Open Access
Synthesis of rectangular waveguide filters with smooth profile oriented to direct metal additive manufacturing
(IEEE, 2023) Percaz Ciriza, Jon Mikel; Hussain, Jabir; Arregui Padilla, Iván; Teberio Berdún, Fernando; Benito Pertusa, David; Martín Iglesias, Petronilo; Arnedo Gil, Israel; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica, Electrónica y de Comunicación; Institute of Smart Cities - ISC; Ingeniaritza Elektrikoa, Elektronikoaren eta Telekomunikazio Ingeniaritzaren
In this paper, a novel design method for rectangular waveguide filters intended for fabrication using direct metal additive manufacturing is proposed. The synthesized filters will feature a smooth profile that allows us to fabricate them orienting the filter propagation axis in the vertical building direction, achieving an optimum configuration for direct metal additive manufacturing fabrication. The novel design method is valid for any all-pole transfer function, which is initially implemented with a commensurate-line distributed unit element prototype. The impulse response of that initial prototype is then properly interpolated to obtain the target response for a smooth-profiled filter with similar length and profile excursion. Finally, the target impulse response just generated is implemented in rectangular waveguide technology employing a novel inverse scattering synthesis technique that relies on the coupled-mode theory to model the electromagnetic behavior of the waveguide filter. The novel inverse scattering synthesis technique is general and also valid for the case of filters with very high rejection levels, which is of great relevance in rectangular waveguide technology. A Ku-band low-pass filter with stringent satellite specifications is designed using the proposed method, fabricated by means of a direct metal additive manufacturing technique, and measured with a vector network analyzer. A very good agreement is achieved between the simulated and measured results, fulfilling the required specifications and demonstrating the feasibility and performance of the novel design method.
Open Access
Optimized pattern design of a light guide using 2D ray-tracing simulation
(SPIE, 2023) Medrano Gurrea, Mario; Jiménez Martínez, Unai; Tainta Ausejo, Santiago; Erro Betrán, María José; Arnedo Gil, Israel; Beato López, Juan Jesús; Izura, J.; Zabala, Silvia; Institute of Smart Cities - ISC
We propose the use of a simplified model for the analysis of the scattering elements used in edge-lit systems. By modelling their behaviour as lambertian light sources whose properties depend on the size and geometry of the scatterer and LGP, it is possible to simulate the illuminance map of the edge-lit structure using only 2D ray-traced simulation. This reduces the computational complexity in the optimisation process used to calculate the scatterers distribution to achieve maximum uniformity in light extraction. The results obtained by comparison between the proposed algorithm and a commercial software demonstrate the validity of the proposal.
Open Access
Producing and exploiting simultaneously the forward and backward coupling in EBG-assisted microstrip coupled lines
(IEEE, 2016) Percaz Ciriza, Jon Mikel; Chudzik, Magdalena; Arnedo Gil, Israel; Arregui Padilla, Iván; Teberio Berdún, Fernando; Gómez Laso, Miguel Ángel; Lopetegui Beregaña, José María; Ingeniería Eléctrica y Electrónica; Ingeniaritza Elektrikoa eta Elektronikoa
In this paper, a methodology is proposed for the design of EBG-assisted coupled line structures in microstrip technology, controlling independently the forward and backward coupling. It is based on the use of a single-frequency-tuned electromagnetic bandgap (EBG) structure to produce a single backward-coupled frequency band, in combination with the forward-coupled frequency bands produced by the difference between the even and odd mode propagation constants present in microstrip technology. Thus, the central frequency of the backward-coupled band is controlled by the period of the EBG structure, while the frequencies of the forward coupled bands are fixed by the length of the device. The rest of the frequencies go to the direct port giving rise to a device with the input port matched at all the frequencies and where the coupled bands are easily controllable by adjusting the corresponding design parameter. The novel methodology proposed has been successfully demonstrated by designing a triplexer intended for the GSM (900 MHz) and WLAN (2.4 GHz and 5.5 GHz) telecommunication bands.