Listar Dpto. Ingeniería Mecánica, Energética y de Materiales - Mekanika, Energetika eta Materialen Ingeniaritza Saila por título
Mostrando ítems 1-20 de 98
-
Adaptación de un motor de combustión interna alternativo de gasolina para su funcionamiento con hidrógeno como combustible. Aplicaciones energética y de automoción
En esta tesis doctoral se presentan los trabajos de investigación realizados recientemente en la Universidad Pública de Navarra sobre la conversión de motores de gasolina para su funcionamiento con hidrógeno, así como el ... -
Análisis de la influencia de las condiciones de proceso sobre el acabado superficial de materiales cerámicos fabricados por electroerosión
El mecanizado por electroerosión (en inglés, Electrical Discharge Machining, EDM) constituye una alternativa emergente frente a otros procesos de fabricación de materiales cerámicos conductores, tales como: mecanizado por ... -
Análisis de la influencia del tratamiento térmico de envejecimiento en la modificación de las propiedades mecánicas de la aleación AA6060 procesada por ECAE
En el presente trabajo se ha realizado un estudio de la modificación de las propiedades mecánicas de la aleación de aluminio AA6060 F, al ser deformada mediante deformación plástica severa empleando el proceso de extrusión ... -
Análisis y modelización de los parámetros de influencia en la electroerosión por penetración de materiales de baja mecanizabilidad
En la presente tesis doctoral se realiza un análisis y una modelización de los parámetros de mayor influencia en la electroerosión por penetración de tres materiales de baja mecanizabilidad. En concreto, el estudio se ... -
Análisis y modelización del daño en elementos mecánicos obtenidos a partir de material nanoestructurado
En la presente tesis doctoral se aborda el diseño de un componente mecánico con estructura submicrométrica, obtenido a partir de material previamente procesado mediante Deformación Plástica Severa (SPD) por Extrusión en ... -
Analysis of fatigue and wear behaviour in ultrafine grained connecting rods
Over the last few years there has been an increasing interest in the study and development of processes that make it possible to obtain ultra-fine grained materials. Although there exists a large number of published works ... -
Analysis on the manufacturing of an AA5083 straight blade previously ECAE processed
Over these past few years, there have been a large number of technical papers published related to the problem of improving the mechanical properties of materials obtained through severe plastic deformation. Nevertheless, ... -
Analytical modelling of energy density and optimization of the EDM machining parameters of Inconel 600
In this present research work, a new modelling of energy density in EDM (Electrical Discharge Machining) is proposed. Energy density can be defined as the amount of energy needed to get a unit volume of material removed, ... -
Auxiliary consumption: a necessary energy that affects thermoelectric generation
Waste heat recovery can apply to a wide range of applications, from transportation, or industries to domestic appliances. Thermoelectric generation technology applied to those cases could produce electrical energy and thus ... -
Caracterización de escorias metalúrgicas procedentes de yacimientos arqueológicos de Navarra (siglos II a.C.- IV d.C.)
Desde la Sección de Arqueología del Gobierno de Navarra llegó la propuesta de caracterizar una serie de piezas comprendidas entre el siglo II a.C. y el siglo IV d.C. procedentes de yacimientos arqueológicos de esta provincia ... -
Caracterización de fundiciones de grafito esferoidal y matriz ferrítica, resistentes al impacto a baja temperatura
El material elegido por los diseñadores de las turbinas eólicas para varios de sus componentes de gran tamaño es la fundición de grafito esferoidal denominada EN-GJS-400- 18-LT. Este tipo específico de fundición pertenece ... -
Caracterización de la microestructura de piezas de fundición compacta (CGI) mediante métodos no destructivos
(Asociación Española de Ingeniería Mecánica, 2004) Contribución a congreso / Biltzarrerako ekarpenaEl desarrollo de los sistemas de inyección directa ha logrado reducir las emisiones contaminantes, y mejorar las prestaciones de los motores diesel. Pero para lograrlo se ha aumentado la presión máxima de trabajo y la ... -
Characterization of two iron bullets from the royal ammunition factory of Eugi (Spain)
In this work, a comparative analysis of two iron bullets found in The Royal Ammunition Factory of Eugi in Navarra (Spain) was performed. Both bullets presented a spherical shape with a relatively good state of preservation, ... -
CO2 emissions reduction and energy efficiency improvements in paper making drying process control by sensors
The drying process of paper has many production parameters that can influence both the energy consumed and the characteristics of paper produced. It was found that most of the previous studies conducted on this process ... -
Comparative study of the damage attained with different specimens by FEM
This present research work deals with the analysis of the design of different specimen geometries so that by finite volume simulations, the appearance of cracks may be predicted in the case of forging processes. To this ... -
Compound Petri nets and alternatives aggregation Petri nets: two formalisms for decision-making support
Decision-making in technological systems, such as communication networks, manufacturing facilities and supply chains, constitutes a common requirement able to lead companies galore to success or failure. This article ... -
Computational and experimental study of a complete heat dissipation system using water as heat carrier placed on a thermoelectric generator
The heat dissipation systems which have liquids as heat carriers outperform conventional dissipation systems at thermoelectric generators (TEGs). However, new elements need to be introduced such as pumps, secondary heat ... -
Computational simulation of scleral buckling surgery for rhegmatogenous retinal detachment: on the effect of the band size on the myopization
A finite element model (FE) of the eye including cornea, sclera, crystalline lens, and ciliary body was created to analyze the influence of the silicone encircling bandwidth and the tightness degree on the myopia induced ... -
Computational study on the thermal influence of the components of a thermoelectric ice maker on the ice production
The main objective of this paper is to study the thermal resistances of two components of a thermoelectric ice maker installed in a no-frost refrigerator, in order to optimize the ice production. This study is conducted ... -
Control of discrete event systems by means of discrete optimization and disjunctive colored PNs: application to manufacturing facilities
Artificial intelligence methodologies, as the core of discrete control and decision support systems, have been extensively applied in the industrial production sector. The resulting tools produce excellent results in ...